Gardeners CedarLast 8596680 User manual

V Rev /#
CedarLast Potting Bench
The CedarLast Potting Bench is the optimum gardening work station, providing a versatile dry sink for planting and cleaning pots.
It combines classic styling with solid cedar construction that will last for years. Its simple design complements any setting, from rustic
to modern.
Parts List Tools Required
() Potting Bench Top () Sink Drain Power drill
() Side Panels () Drain Plug Flat head screwdriver
() Front/Back Panels () Drainage Hose Rubber mallet (optional)
() Shelf Supports () " Long Screws
() Sink () ." Short Screws
() Trellis () Star Bits for your power drill
() Trellis Supports
() Shelf
() Sink Grate
Assembly
NOTE: Assembly is easiest with two people.
Step 1. Place the Side Panels upside down on a flat, protected surface. Slide the Front and
Back Panels into the slots on both Side Panels, as shown in Figure . NOTE: The platforms
on the Front and Back Panels should be closer to the top of the Potting Bench.
Step 2. Place the ends of the Shelf Supports into the openings on the Side Panels (Figure
). Make sure all pieces are fully in place and use the larger Star Bit to attach them together
by inserting Long Screws into the  predrilled holes in each Corner (Figure ).
Step 3. Remove the nut and washer from the bolt attached to the Drain Plug (Figure ).
Place the Bolt through the small hole in the corner of the Sink and reattach the
washer and nut (Figure ).
Step 4. Use your flat head screwdriver to remove the bolt and the strainer from
the Sink Drain. Line up the Drain with the bottom of the larger hole in the Sink
(Figure ). Place the strainer on top of the hole, lining it up with the rest of the
Drain and reattach the Bolt through the center. NOTE: Before tightening the bolt,
make sure the Drain's overflow is pointed in the direction you want water to
drain.
Step 5. Sit the Potting Bench upright. Place the Sink into the top of it, making
sure it is centered (Figure ).
over please
attach Drain Plug here
attach Sink
Drain here
Figure 4
Sink
Side Panel
Long
Screws
Figure 2
Sink
Drain
Drain
Plug
attached bolt with
washer & nut
strainer bolt
Figure 3
overflow
Side Panels
Shelf Supports
Front/Back
Panels
Figure 1
slot
platform
back of the Potting Bench sink
Figure 5

Phone Orders: 1-800-427-3363 • Customer Service: 1-800-876-5520
e-mail: inf[email protected]om • Web: www.gardeners.com
Step 6. Place the rectangular Potting Bench Top on a flat protected surface. Flip the Potting Bench with the Sink upside down and
place it on the Top. Important: The Top is slightly larger than the Frame. Center the Bench so the Top extends evenly along each side.
Use the other Star Bit to place Short Screws into the  holes in the bottom of the Potting Bench, attaching it to the Top (Figure ).
Step 7. Lay the Trellis face down on a flat, protected surface. Place a Trellis Support on each end of the Trellis, with the wider half of
the Support positioned against the Trellis (Figure ). NOTE: Line up the bottom edge of the Trellis with the top of the notch in the
Support (Figures  & ). Make sure the Supports are straight and place Short Screws through the top two holes in each Support,
attaching them to the Trellis.
Step 8. Stand the Trellis upright and place it along the back of the Potting Bench (Figure ). Make sure it is centered and use the Star
Bit to place Short Screws through the bottom two holes in each Trellis Support, attaching the Trellis to the Potting Bench (Figure ).
Step 9. Sit the Shelf on the Shelf Supports (Figure ) and sit the Sink Grate over the Sink. Attach the end of the Drainage Hose to Sink
Drain's overflow. Your assembly is complete!
Figure 9
Shelf
predrilled holes
Figure 6
bottom of the
Potting Bench
Trellis
Trellis Supports
Figure 7
notch
Trellis
Support
Trellis
Potting
Bench
Figure 8