Garlando TOORX SRX500 User manual

Ed : Rev : Cod :
INSTRUCTION
09/19 GRLDTOORXSRX50001

2
EXPLOSIVE VIEW

3
PARTS LIST
PART NO.
DESCRIPTION
QTY
1
Main frame
1 PC
2
Front tube
1 PC
3
Rear tube
1 PC
4
Seat tube
1 PC
5
Handlebar post
1 PC
6
Handlebar
1 PC
7
Computer
1 PC
8
Slider
1 PC
9
Seat
1 PC
10
End cap
4 PCS
11
Hexagon nut M10
6 PC
12
Food pad
4 PCS
13
Step screw
4 PCS
14
Bearing
2 PCS
15
Flat washer φ20
3 PCS
16
Belt pulley
1 PC
17
Alex
1 PC
18
Hexagon screw
4 PCS
19
Belt
1 PC
20
Chain cover(R+L)
1 SET
21
Tapping screw
4 PCS
22
Screw
7 PCS
23
Screw M5*10L
4 PCS
24
Trim cover(R+L)
1 SET
25
Crank(R+L)
1 SET
26
Flange nut M10
4 PCS

4
27
Crank plug
2 PCS
28
Pedal (L+R)
1 SET
29
Pipe
1 PC
30
Hexagon nut
2 PCS
31
L knob
1 PC
32
Tube clamp
2 PCS
33
L knob
2 PCS
34
Flat washer φ10
2 PCS
35
Magnetic steel frame holder
1 PC
36
Magnetic steel frame
1 PC
37
Cable
1 PC
38
Limit spring
1 PC
39
Screw M5*6L
2 PCS
40
Brake limit bushing
1 PC
41
Brake nylon bushing
1 PC
42
Brake rod
1 PC
43
Hexagon nut M8
3 PCS
44
Brake trim cover
1 PC
45
Brake knob
1 PC
46
Limit bushing
2 PCS
47
Screw M4.2
2 PCS
48
Hexagon screw M8
1 PC
49
Strong magnets
10 PCS
50
Flat elliptic pipe plug
1 PC
51
Flat washer
4 PCS
52
Flywheel trim cover
1 PC
53
Cable
1 PC
54
Screw M5
11 PCS
55
Brake shrapnel
1 PC

5
56
Brake pad
1 PC
57
Screw M8
3 PCS
58
Plastic bushing
2 PCS
59
PU moving flywheel
2 PCS
60
Cable plug
1 PC
61
Nylon cap M8
3 PCS
62
Plastic bearing
4 PCS
63
Flange nut M12
2 PCS
64
Flat washer
2 PCS
65
Ring
4 PCS
66
Flywheel axle
1 PC
67
Flywheel
1 PC
68
Bearing
2 PCS
69
Corrugated gasket
3 PCS
70
Adjuster
2 PCS
71
Nylon cap M6
2 PCS
72
C clip
1 PC
73
Cable
1 PC
74
Adapter
2 PCS
75
Motor
1 PC
76
DC cable
1 PC
77
Hexagon screw
2 PCS
78
Screw
6 PCS
79
I-pad holder
1 PC
80
Knob
1 PC
81
Harpoon wrench
1 PC
82
Hexagon wrench
1 PC

6
ASSEMBLY INSTRUCTION
STEP 1
Attach the rear tube (3) to the main frame(1) using two sets of cap nut(13)by
hexagon wrench(82).
Attach the front tube (2) to the main frame same as the rear tube.

7
STEP 2
Put seat post (4) insert main frame with knob (81)adjust height.
Attach slider(8) to seat post by washer(34) and Knob(33).
Put seat (9) on the slider(8) and fix it by harpoon wrench(81).

8
STEP 3
The pedals (28L and 28R) are marked “L” and “R”-left and right.
Connect them to their appropriate crank set(25L and 25R) by harpoon
wrench(81).
The right crank set is on the right hand side of the cycle as you sit on it.
Note that the Right pedal should be threaded on clockwise and the left pedal
on anti-clockwise.

9
STEP 4
Fix the i-pad shelf(79) on the handlebar(6) using screws(78),put computer(7)
into i-pad shelf, and fix handlebar on handlebar post(5) by washer(34) and
knob(33), then put handlebar on the main frame by knob(31).
And insert the sensor plug(53) into the sensor joint of computer.
Now your spinning bike is finished for use.

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]