Gator G42V User manual

Connects2Vision
- Resolution 720 x 480 (Wide Angle View)
- Picture Mode NTSC
- CMOS Chipset: 1/3”
- Lens FOV: 210 Degrees (H) x 140 Degrees (V)
- Viewing Angles: Birds-Eye, Wide Angle, Reversing Left/Right Blind Spot, Driving
- Waterproof Rating: IP67
- Parking Guidelines Yes (Removable/Dynamic)
Prior to Installation
Read the manual prior to installation. Technical knowledge is necessary for installation. Please ensure you use
the correct tools to avoid damage to the vehicle or product.
Aerpro can not be held responsible for the installation of this product.
Technical Support
TDJ want to provide a fast and suitable resolution should you encounter any technical issues. With this in mind,
when contacting TDJ, try to provide as much information as possible. This will speed up the process and help us
to help you.
Please visit gatordriverassist.com/contact
Wide Angle Universal Brake Light Camera
2-in-1 Reversing Camera/Brake Light Solution
with Wireless Controller
PRODUCT FEATURES:
User Manual
G42V
V1-10-19

gatordriverassist.com
2
Connects2Vision
CAM-42
Extension Cable
Power Adapter
Cable
Make Connections to Vehicle/Unit
Camera replaces OEM brake light
Control Unit
Wireless Controller (Mount on dashboard)
Control Unit
Extension Cable
Power Adapter
Cable
Vehicle Connection Overview
Wiring Diagram
INSTALLATION
1 Red Acc 12V Connect to vehicle 12V Accessory feed
2 Black Ground Connect to ground
3 Green Reverse Trigger Connect to vehicle reverse trigger output
4 Blue CAN + Connect to rear of OBD connector (see diagram on Page 3)
White CAN - Connect to rear of OBD connector (see diagram on Page 3)

gatordriverassist.com
3
Connects2Vision
Extension Cable
USING THE WIRELESS CONTROLLER
The wireless controller included in the kit can be used to change the viewing mode of the camera, as
well as adjust key parameters for each viewing mode.
To bring up the HUD menu, put
the vehicle into reverse gear and
press A.
Note: The HUD menu will time-out
after 3 seconds to allow an unin-
hibited view of the camera image.
Press the A button to bring the HUD
menu back onto the screen
The currently selected viewing mode is displayed by the icon in the centre of the HUD menu. This will
default to Driving/Rear-View mode, or to Reversing mode when in reverse gear.
To change the camera mode, whilst the vehicle is in reverse gear, press B or C to cycle through the
Reversing, Wide Angle and Birds-Eye viewing modes.
Start-Up
HUD Menu
Switch to
Wide Angle
Switch to
Birds-eye
Go to Settings
Currently selected view
Viewing Modes
Reversing (Select from HUD Menu) Driving/Rear-View (Default view when not in reverse)
A
BC
Connecting CAN-Bus Wiring
FRONT OF OBD CONNECTOR
FRONT OF OBD CONNECTOR
Locate the vehicle’s OBD port and unscrew/
remove the female connector.
On the reverse of the connector (the side
where wiring enters it), connect the CAN
+ (blue) and CAN - (white) wires from the
harness to the locations specied in the
diagram (Pins 1 and 9).
12345678
10111213141516 9

gatordriverassist.com
4
Connects2Vision
Adjusting Settings
To adjust settings for all viewing modes, press A from the HUD menu to enter the settings menu.
Once in the settings menu, short press A to cycle through the various settings screens available. Screens
include camera angle and position for each mode, and guideline width for parking lines.
Once in a settings screen, the selected setting is indicated by the icon in the centre of the display. The
parameters can be adjusted with B and C.
To return to the previous screen, Press and hold A.
Activating/Deactivating Blind Spot View (BSV) Mode
When in any of the settings screens, a long press of B will activate or deactivate BSV (Blind Spot View).
When active, this will trigger the blind spot camera image when an indicator is activated and the vehicle
is moving at a speed of over 40km/h.
When inactive, using the indicators will not trigger the blind spot view and the camera will remain in
Driving/Rear-View mode.
Note: this function will only work if the CAN-Bus wiring is connected.
Move to next setting
(Short Press)
Return to previous
(Long Press)
Adjust parameter
Adjust paramater
(Short Press)
Activate/Deactivate BSV
(Long Press)
Currently selected
setting
A
C
B
Birds-Eye (Select from HUD Menu) Left Blind Spot (Triggered by Indicator - See Page 4)
Wide Angle (Select from HUD Menu) Right Blind Spot (Triggered by Indicator - See Page 4)