Gator GRV43KT Operational manual

PAGE 1
GRV43KT INSTRUCTION MANUAL
PRODUCT USER MANUAL

PAGE 2
GRV43KT INSTRUCTION MANUAL
INTRODUCTION
WELCOME
Thank you for purchasing the Gator GRV43KT 4.3” Monitor + Reverse
Camera. Please ensure that you have read the product manual and
instructions in full, prior to installation and use. Failure to do so may result
in product failure/damage or incorrect operation and therefore impact the
product performance.
PRODUCT FEATURES
• Monitor
• 4.3” 16:9 High-resolution LCD screen
• Resolution 480*272
• 12V Compatible
• Secondary Video RCA Input
• Dimensions 88(H) x 116(W) x 34mm(L)
• Buttery Camera
• 170 Degree wide angle lens
• Parking guide lines
• IP-67 Dust and water protection
• CMOS Sensors
• 0.2 Lux
• NTSC/PAL
• 5.5M Video extension cable with trigger
PACKAGE COMPONENTS
Parts supplied include:
• Monitor
• Buttery mount camera
• 5.5M RCA extension cable
• Instruction manual
• Monitor harness
• Camera harness

PAGE 3
GRV43KT INSTRUCTION MANUAL
TABLE OF CONTENTS
INTRODUCTION.........................................................................PAGE: 2
PRODUCT FEATURES..............................................................PAGE: 2
PACKAGE COMPONENTS .........................................................PAGE: 2
TABLE OF CONTENTS..............................................................PAGE: 3
INSTALLATION OF MONITOR .................................................... PAGE: 4
INSTALLING THE CAMERA ...................................................... PAGE:5-6
TESTING THE REVERSE CAMERA FUNCTION ........................ PAGE:7
MENU FUNCTIONS ....................................................................... PAGE:7
PRODUCT SPECIFICATIONS ....................................................... PAGE:8
TECHNICAL ASSISTANCE ........................................................... PAGE:8

PAGE 4
GRV43KT INSTRUCTION MANUAL
INSTALLATION
Installation diagram
The video signal is transferred from the camera to the GRV43KT monitor
via an RCA cable that will need to be run through the boot, through the
passenger compartment to the mirror monitors wired loom run under the
dash. From there the power and video signals are sent directly to the
monitor. At the rear of the car the camera is powered directly from the
reversing tail light. Priority is the AV2 input.
(Red wires can
be used for
additional
accessories )
F
F
F
F
M
M
F
F
F
F
Moulded
splitter
Moulded
splitter
M
Powerwires
(ACC)
+
M
M
+
Camera
5.5 Metres
(Optional front camera)
Powerwires
(Reversing light)
Monitor

PAGE 5
GRV43KT INSTRUCTION MANUAL
INSTALLATION
Installing the camera
In most instances, the camera is best mounted above the vehicles license
plate as shown here.
1. Connect the RED wire of the Cameras Power Harness to the wire that
supplies power to the reversing light globe (the wire that is energized only
when the car is put into reverse). Before making the electrical connection,
temporarily disconnect the camera from the power plug whilst making
the connection to the reversing light globe. Use a suitable splicing/crimp
connector (scotch lock type) or strip connector. This connection can also
be soldered, making sure to insulate the joint with electrical insulation when
done. The camera has only one wire to connect (positive (+). There is no
need to hook up a ground earth wire as the camera gets its earth through
the RCA cable. Hooking up the ground earth may cause a ground loop. In
this case horizontal lines will appear in the image.
NOTE: CAN BUS
In the event that the cars reversing lights are driven by CAN BUS the above
wiring system may not trigger the system correctly. It may even create a
globe fault warning. In this case a CAN BUS module (sold separately) may
need to be installed. However, just because the vehicle has a CAN BUS
system does not necessarily mean that it will require such a module to
work. In fact the opposite is true. Most vehicles do not require an additional
module. If a CAN BUS module is required we recommend seeking advice
from a professional installer.

PAGE 6
GRV43KT INSTRUCTION MANUAL
INSTALLATION
Installing the camera....cont
2. After you have insulated the join you can connect the power harness to
the camera.
NOTE:
Some cars that run LED or computer controlled lighting systems may not
deliver enough voltage to run the camera. If the voltage at the reversing
wire light is less than +12 volts it may be necessary to use a relay to supply
power to the transmitter harness from the wiring in the front of the car. In
this case the reversing light only needs to trigger the relay. Make sure that
you do not drill holes in the panels that have an opposite face that is visible
outside the car for example guard panels. In fact, whenever drilling holes in
the bodywork of a vehicle, always see what is on the other side.
3. Connect one end of the supplied RCA cable to the RCA socket from the
camera, then run the RCA cable to the front under side of the driver side
dash board. This is where the monitor’s loom will be located. To do this you
will need to remove the rear seat to pass the cable into the cabin area and
you will need to remove the door scuff plates to run the wire along the side
of the vehicle. The RCA cable will be hidden when you replace the scuff
plates. When the cable is at the front of the vehicle the RCA cable needs to
be run from the scuff plate area to the underside of the dash behind the kick
trim (remove and run cable).
4. The monitor has two power wires to be connected. Connect the red
wire (accessories +12V) to a wire that is energized when the vehicles
accessories is turned on.
Connect the black wire to a ground earth wire or to the body of the car using
the steel of the cars body behind the kick trim as an earth. In this case drill
a small hole and connect the wire using a suitable ring terminal. Scrape off
the cars paint around the hole to ensure good earth.
5. Connect the RCA cable to the RCA socket from the monitors loom.

PAGE 7
GRV43KT INSTRUCTION MANUAL
MENU FUNCTIONS
Menu options and settings
1.Engage the park brake and turn the ignition key to the on position.
DO NOT start the vehicle.
2. Select reverse gear with the gear shift. The monitor will sense the video
signal from the camera automatically and will display the camera’s image of
the rear of the vehicle.
TESTING THE REVERSE CAMERA FUNCTION
1. Press the Menu button to access functions
2. Press the + or - button to conrm selection
- Brightness: Adjusts screen brightness (50 - 100)
- Contrast: Adjusts screen contrast (50 - 100)
- Saturation: Adjusts screen saturation (50 - 100)
- Tint: Adjusts screen tint (50 - 100)
- Language: Select menu language
- Mode: Changes display mode between 16:9 & 4:3 ratio
- Reset: Resets all menu setting back to factory conguration

PAGE 8
GRV43KT INSTRUCTION MANUAL
TECHNICAL ASSISTANCE
If you need assistance setting up or using your Gator product now or in the future, call
Gator Support.
Australia
TEL: 03 – 8587 8898
FAX: 03 – 8587 8866
Mon-Fri 9am – 5pm AEST
Please retain this user guide for future reference.
If you would like to download a digital copy of this manual, or other Gator manuals/
software, please visit the http://gatordriverassist.com website and click on ‘Firmware &
Manuals” for information on
where to nd the manuals/software.
This manual is considered correct at time of printing but is subject to change. For latest
manuals and updates refer to the website.
Copyright © 2017 by TDJ Australia
All rights reserved. No part of this publication may be reproduced, distributed, or
transmitted in any form or by any means, including photocopying, recording, copying
or other electronic or mechanical methods, without the prior written permission of the
author.
PRODUCT SPECIFICATIONS
Monitor
- Size: 4.3 inch colour TFT LCD Screen
- Resolution : 480*272 (500 Candela)
- Video Input : Yellow = Reverse Camera Input
- Supply Power: DC12V +/- 10%
-NTSC/PAL
Buttery Camera
- Aluminum case & waterproof for outdoor use.
-IP67 Standard
-Lense Angle 170 degree
-Low-Lux CMOS camera
-Parking guide lines
-NTSC