Gator GALT02 User manual

gatordriverassist.com
For more information
on the Gator range
go to our website
QUICK START GUIDE
GALT02

1
Please ensure that you have read the product quick start
guide and instructions prior to installation and use. Failure to
do so may result in the product incorrectly operating or an
installation that renders the device unusable.
Product specifications
•Pitch angle: -40° - +40°
•Roll angle: -40° +40°
•Temperature accuracy: ±1°C
•Air pressure: 300-1100hPa
•Voltage measurement range: DC 5-30V
•Voltage measurement accuracy: 0.5 V
•Speed precision: <0.36 Km/h
•GPS start time (Cold): 32s (Average)
•GPS start time (Hot): 1s (Average)
•Data refresh rate of GPS: 1s
•Operating temperature: -40°C+80°C
•Power supply: DC 10V-30V
•Ambient light modes: 24 kinds

Display
2
Elevation Altitude
Pitch
Roll
Longitude & Latitude
Barometer
Digital Compass
Speed Meter
Thermometer
Voltage Indicator
Digital Clock / Date
Fatigue Alarm
GPS Data Collection
Volume Adjustment
Auto Brightness
Ambient Light
Speaker
Ambient Light Mode Setting/
Pitch & Roll Angle Reset

Functions
3
1. Elevation
Altitude
When GPS data is collected, it will display the
elevation altitude.
2. Pitch Displays the pitch angle of the car's current
position.
3. Roll Displays the roll angle of the car's current
position.
4. Longitude
& Latitude
Displays the longitude & latitude of the vehicle's
current location when GPS data is received.
5. Barometer Displays the atmospheric pressure at the current
location of the vehicle.
7. Speed
Meter
When GPS data is collected, it will display the
vehicle speed.
6. Digital
Compass
When GPS data is collected, it will display the
east, south, west, north, southeast, southwest,
northeast, northwest directions according to the
motion track of the vehicle.
10. Electronic
Clock
Display the year, month, day, hour of the week.
After GPS data is obtained, it is automatically
calibrated according to satellite timing.
8. Indoor
Thermometer
It gets and displays the thermometer through the
temperature sensor in the concentrator.
9. Voltage
Indicator
Displays the actual voltage when the display is
connected with the power (in Volts).

11. Fatigue
Alarm
When the vehicle has been working continuously
for 4 hours, a fatigue driving icon will be
displayed on the display to remind the driver that
he needs to rest.
Functions
4
12. GPS data
Collection
When GPS data is collected, it will display GPS
icon to show that GPS data collection is in a
normal state.
13. Volume
Adjustment
Adjust device volume. Each press will cycle
up through the values (0-9/ 0 is Mute)
14. Auto
Brightness
The display will auto adjust the backlight
brightness according to the outside brightness,
so to make the display clear, soft and not
dazzling.
15. Ambient
Light
An ambient light strip is set under the display,
and there are 0-24 ambient light display modes
to choose from, and the ambient light can also
be turned off as needed.
16.
Overspeed
Alarm
The display will alarm and make a beep, when
the car speed exceeds the threshold, meanwhile
the display speed will flash accordingly.

Installation
5
1. Connect the ACC wire to the ACC power supply of the
car, then connect the GND wire to a suitable ground
point.
2. The plug of GPS module should be plugged into the
socket of the concentrator, then position the GPS module
in a suitable location on the dashboard in the vehicle to
receive optimal signal.
3. It is recommended that the display is installed on the
centre of the dashboard, close to the windscreen to
enable wires to be hidden and ensure a good view for the
driver. Install the display using 3M tape after first cleaning
the surface.
4. After turning on the device for the first time, or after
having moved the device, press and hold the reset button
(17) whilst the device is powered on for 3-5 seconds to
reset/zero the pitch and roll angle to ensure that the
values are accurate.
Concentrator
External GPS
Module

Settings
Volume:
To change the default volume of the device, press the
Volume Button(13) whilst the device is on. Each press will
cycle up through the values (0-9/ 0 is Mute)
Time Zone:
To change the default time zone of the device, press and
hold the Reset button(17) whilst the device is off (vehicle
ignition is switched off). Then switch on the vehicle ignition,
the current time zone setting will be displayed on the
Temperature/Voltage display (8)(9).
Note: The default time zone is set to GMT.
Press the Power Button(17) to cycle to the desired value and
then turn off the device. When the device is next powered on,
the time zone will be set to the chosen value.
Measurement:
To measurement readings (speed, altitude,temperature) of
the device can be adjusted from metric to imperial.
Note: The device is set to Metric by default.
To change the measurement type, Press and hold the Volume
Button(13) whilst the device is off (vehicle ignition are
switched off). Then switch on the vehicle ignition. The 'km/h
'M' 'C' (Metric) or 'mph', 'Ft, 'F' (Imperial) will be
6
Speed
Altitude
Temperature
Metric
Km/h
m
°C
Imperial
Mph
ft
°F

Settings cont...
displayed on the screen. To cycle between the options, turn
off the ignition and press and hold the Volume Button(13) to
display the next option. Once the desired option has been
set, turn on the device, the measurement will be set to the
chosen type.
Ambient Light Mode:
The system provides a total of 24 ambient light modes from
0 to 24 to choose from. Each time you press the Power
Button(17), the mode value is incremented by 1, and it is
adjusted in cycles.
The corresponding relationship between the mode value and
the ambient light mode is as follows:
0: No light
1: Colorful lights
2: Phantom lights
3-9: 7 Kinds of color static light
10-16: 7 Kinds of color breathing light
17-23: 7 Kinds of color running water light
24: Speed light
Over Speed Alarm Setting:
To change speed setting for overspeed alarm, press and hold
the Volume Button(13) while the device is powered on for 3-5
seconds, the current speed setting will be displayed on the
Speed display (5).
Note: The default speed is set to 190Km/h.
Press the Volume Button(13) to cycle to the desired value
thenzzz wait for 3-5 seconds, the speed will be set to the
chosen value.
7

Attention:
1. Due to the affect of the GPS signal, the speed may be
delayed, and at the same time, the speed, electronic
compass and elevation altitude can't be displayed
normally.
2. The GPS signal has a great influence on the elevation
altitude, so the lack of GPS signal is a little bigger when
it's obstructed by surroundings (ie buildings, forest).
3. The temperature sensor is inside the concentrator, so the
indoor temperature is dependent on its position inside the
vehicle.
Technical assistance
If you need assistance setting up or using your Gator product
now or in the future, call Gator Support Australia.
TEL: 03 – 8587 8898
FAX: 03 – 8587 8866
Mon-Fri 9am – 5pm AEST
Please retain this user guide for future reference
This manual is considered correct at time of printing but is
subject to change. For latest manuals and updates refer to
the website.
Copyright © 2022 by TDJ Australia
www.gatordriverassist.com
8