Gazer F715 User manual

USER MANUAL

DASHBOARD CAMERA

GAZER F715

User manual �� 4-17

Руководство пользователя �� 18-32

Посібник користувача �� 33-46

ENG

1. Precautions ..........................................................................5

2. Important information.............................................................6

3. Package contents ...................................................................7

4. Controls ...............................................................................8

5. Connecting the dash cam ........................................................9

6. Using the dash cam .............................................................. 10

7. Installing the dash cam ........................................................ 11

8. Description of indicators........................................................ 12

9. Button functions .................................................................. 13

10. Preparing the memory card ................................................... 14

11. Preparing the dash cam ........................................................ 15

12. Menu settings ...................................................................... 16

13. Product specications .......................................................... 17

Contents

ENG

Gazer F715

Congratulations! You are now the owner of a Gazer dash cam.

Make sure that you read this manual carefully before using the product.

Precautions

•Never use chemicals to clean the product.

•Please, use a soft cloth to clean the dash cam body and lens.

•Avoid hitting, dropping, and damaging the product mechanically.

•Do not use and store the product in extremely cold or hot environments.

- Storage temperature range: from -20 °С to +40 °С

- Operating temperature range: from +5 °С to +40 °С

•Should the equipment be exposed to low temperatures for a long time,

make sure that you warm it up to an operating temperature rst before

proceeding with connection and startup.

•Do not attempt to repair the dash cam yourself. In case of malfunctions,

contact the vendor or the service center.

•Neither the manufacturer nor the vendor shall be responsible for any

damages or lost prot due to the use of video footage and data obtained

with this dash cam.

ENG

Important information

Caution!

•Do not insert or remove the SD card when the power is on – this can lead

to dash cam malfunction. Prior to inserting or removing the memory card,

make sure that the dash cam is switched o or that its power has been

turned o for at least 30 seconds and its indicators went dark at least

10 seconds ago.

•Set the correct time and date before using the product.

•Observe at least half a second time interval while pressing control buttons.

Otherwise you may need to reboot the dash cam by unplugging the power

cable.

• Do not turn o the power for at least 20 seconds after the power cable is

connected. This is necessary to ensure the dash cam’s normal operation.

•If after starting the engine (with the power cable connected) the dash cam

fails to switch to the recording mode automatically, turn ACC power o for

10 seconds and then turn it back on.

•To install and connect the dash cam without voiding your vehicle warranty,

please contact an authorized service station.

• Loop recording of G-sensor write-protected les is limited to 30% of the

total storage space on the memory card. Files protected from overwriting

by pressing a special button use the same storage space but cannot be

overwritten. It is recommended to format the memory card every once in

a while or backup «accident» footage to a PC so that video recording never

stops due to insucient space.

ENG

Package contents

Gazer F715 dash cam Extra 3M tape for mounting

User manual

Power, control, and composite RCA

video output cable

Memory card micro SDHC Gazer +

Adapter*

3М adhesive pad for dash cam

mounting

* Depending on the region.

ENG

Controls

1. • REC Button – start or stop

video recording.

2. LEFT button – menu navigation.

3. RIGHT button – menu

navigation.

4. ОКbutton – selecting a

parameter in the menu.

5. Microphone.

6. PWR – power indicator (red).

7. А – sound recording indicator

(yellow).

8. V – video recording indicator

(blue).

9. Memory card slot – micro SD.

Do not insert or remove your SD

memory card when the power or

indicator lights are on.

10.Mount.

11.Lens.

12.Connector – for power cable

connection and video output.

1012 11

1 6 7

You can turn o the dash cam manually. To prevent the loss of the last recorded

clips, rst stop the recording by pressing • REC and then turn the dash cam o

by holding down • REC. Use the same button to turn the dash cam back on.

All button functions and indicator operation modes are described in detail on

p. 12-13.

ENG

Connecting the dash cam

Note: Gazer F715 dash cam requires direct connection to the car’s electrical

system. To install and connect the product without voiding your vehicle

warranty, please contact an authorized service station.

Connect the black wire (GND) to the vehicle’s ground. Connect the yellow wire

(BATT +) directly to +12 V car battery terminal or DC +12 V power line. Connect

the red wire (ACC) to the car’s +12 V ACC power wire (ACC power turns on when

the car engine starts and turns o when it stops).

When connected this way, the dash cam will turn on automatically and start

recording as soon as the car engine starts. Once the engine is turned o, the

dash cam will continue recording for one hour (default setting) after which the

recording will stop and the dash cam will shut down. You can select the recording

duration and dash cam operating mode after the engine is turned o using “Auto-

o time” and “Parking vibration” settings.

ENG

Using the dash cam

You can use the dash cam for CCTV recording when the car is parked. For this

you need to set the dash cam on-time after the ignition is turned o in “Auto-o

time” setting. In this case, when ACC power is o (i.e. when the engine is turned

o) the dash cam will continue operating in the Time-Lapse mode (1 fps). “Car

battery protect” function – prevents your car’s battery from depletion. The dash

cam will shut down correctly if the battery voltage drops below the minimal value

set in this menu item.

Note: Please, consult with an authorized service station prior to

changing “Car battery protect” settings.

When ACC power is o, the dash cam can operate in two modes that can be

selected in the “Parking vibration” item of the menu.

1. Dash cam operation with Time-Lapse mode (“Auto-o time”) and

parkingmode(“Parkingvibration”)on.

When set up this way, after ACC power is turned o, the dash cam continues

recording for 1 hour (default setting) in Time-Lapse mode with recording speed

reduced to 1 frame per second to save space on the memory card. If the

G-sensor detects an impact, the dash cam will record a 2-minute long write-

protected video le at 30 frames per second.

2. Dash cam operation with Time-Lapse mode (“Auto-o time”) on and

parkingmode(“Parkingvibration”)o.

When set up this way, after ACC power is turned o, the dash cam continues

recording for 1 hour (default setting) in Time-Lapse mode with recording speed is

reduced to 1 frame per second to save space on the memory card. In this mode,

the G-sensor will neither detect any impacts nor aect the recording mode.

ENG

Installing the dash cam

Prior to installation, position the dash cam

accurately on the windshield. Use a felt-tipped

pen to mark the mounting location. Keep in

mind that once the mount is xed on the

windshield you will not be able to change the

dash cam’s horizontal position (right-left) and

only vertical position adjustment (up-down)

will be possible.

Make sure that the dash cam is installed

conveniently. Fix the mount so that other

objects would not prevent you from

monitoring indicators on the dash cam front

panel, inserting or removing the memory card,

or pressing any buttons.

Peel o the protective lm from 3M tape. Mount the dash cam on the windshield in the

intended spot using 3М adhesive pad.

Rotate the dash cam vertically to point its lens

down at about 15°.

To remove the 3M mounting pad from the

windshield, use a ruler or plastic card and

push it gently between the mount and the

windshield.

Caution! Degrease the windshield surface before mounting. Make sure

that the mounting location is dry and clean. Do not apply the 3M adhesive

mounting pad if the ambient temperature is below +5 °С. Due to low air

temperature and a signicant dierence between temperatures inside and

outside the car, 3M tape may lose its adhesive properties and make secure

mounting impossible.

ENG

Description of indicators

Power

indicator

PWR(red)

Sound

indicator A

(yellow)

Recording

indicator V

(blue)

Status description

ACC is on