Gazer H521 User manual

Contents

Contents
3
ENG

Gazer H521
Congratulations on your purchase of Gazer
mobile video recorder.
Please read this manual carefully, before using the device.
Warnings
•Do not expose the device to direct sunlight.
•Do not apply any chemicals when cleaning the device. Only use
soft cloth to clean the frame and the lens.
•Prevent the device from falling or being damaged by other objects.
•Do not use or store the device in cold or hot places.
- Storage temperature: -20°C to +40°C
- Operation temperature: from +5°C to +40°C
•Make sure the device warms up before starting, if it was exposed
to the low temperature for too long.
•Do not attempt to repair the appliance yourself. In case of
damage, contact your dealer or service center.
•The manufacturer is not responsible for any losses or missed
opportunities due to use of videos and data obtained with the help
of this MVR.
Important information
Warning!
•Do not insert or remove the SD card when the device is on - this
can lead to MVR malfunction. Wait for 30 seconds after the MVR
shutdown, make sure that all the lights are off for at least 10
seconds, and only then safely remove the memory card.
•Set the correct time and date before using the device. The MVR
may not record in case these settings were entered incorrectly.
•Use at least 0.5 seconds time interval while pressing control
buttons, otherwise you may need to unplug the MVR power supply
cable in order to reboot the system.
•Carefully connect the power supply cable to the device. MVR power
supply cable should not be confused with the radar detector or
navigator power supply cables (those may have voltage of +12 V).
A wrong connection may cause MVR failure.
•Do not turn off the power for at least 20 seconds after the power
supply cable is connected. This is necessary to help the built-in
battery function correctly.
•If after you have started the car (when the power supply cable is
connected to the MVR), the device failed to switch to the recording
mode automatically, simply unplug the power supply cable for ten
seconds and then try again.
•Use the restart option (by removing the battery from the MVR,
when the power supply cable is disconnected) in the following
cases:
• Power indicator is not on, when the power supply cable is
connected;
• The device does not switch from the standby to the recording
or control mode;
• The device fails to function properly.
•To restart the MVR, turn the power off, remove the battery cover
(p. 7, c. 9) and carefully remove the battery from the slot for at
least 5 seconds. Then put the battery back, close the cover and
reconnect the power supply cable.
ENG
4

Gazer H521
Congratulations on your purchase of Gazer
mobile video recorder.
Please read this manual carefully, before using the device.
Warnings
•Do not expose the device to direct sunlight.
•Do not apply any chemicals when cleaning the device. Only use
soft cloth to clean the frame and the lens.
•Prevent the device from falling or being damaged by other objects.
•Do not use or store the device in cold or hot places.
- Storage temperature: -20°C to +40°C
- Operation temperature: from +5°C to +40°C
•Make sure the device warms up before starting, if it was exposed
to the low temperature for too long.
•Do not attempt to repair the appliance yourself. In case of
damage, contact your dealer or service center.
•The manufacturer is not responsible for any losses or missed
opportunities due to use of videos and data obtained with the help
of this MVR.
Important information
Warning!
•Do not insert or remove the SD card when the device is on - this
can lead to MVR malfunction. Wait for 30 seconds after the MVR
shutdown, make sure that all the lights are off for at least 10
seconds, and only then safely remove the memory card.
•Set the correct time and date before using the device. The MVR
may not record in case these settings were entered incorrectly.
•Use at least 0.5 seconds time interval while pressing control
buttons, otherwise you may need to unplug the MVR power supply
cable in order to reboot the system.
•Carefully connect the power supply cable to the device. MVR power
supply cable should not be confused with the radar detector or
navigator power supply cables (those may have voltage of +12 V).
A wrong connection may cause MVR failure.
•Do not turn off the power for at least 20 seconds after the power
supply cable is connected. This is necessary to help the built-in
battery function correctly.
•If after you have started the car (when the power supply cable is
connected to the MVR), the device failed to switch to the recording
mode automatically, simply unplug the power supply cable for ten
seconds and then try again.
•Use the restart option (by removing the battery from the MVR,
when the power supply cable is disconnected) in the following
cases:
• Power indicator is not on, when the power supply cable is
connected;
• The device does not switch from the standby to the recording
or control mode;
• The device fails to function properly.
•To restart the MVR, turn the power off, remove the battery cover
(p. 7, c. 9) and carefully remove the battery from the slot for at
least 5 seconds. Then put the battery back, close the cover and
reconnect the power supply cable.
5
ENG

ENG
6
Package contents
Gazer H521 MVR Warranty Card User Manual
Battery 40C
3,7V 500mAh
Vacuum windshield
mount
3M scotch tape mount
USB-cable
for PC connection
Memory Card
Gazer micro SDHC
+ adapter
Cigarette lighter
socket power unit
(with an integrated
+ 5V converter)
Controls
1. IR diodes.
2. Lens.
3. Status indicator
(blue – operation mode,
red – charging mode).
4. Microphone.
5. Speaker.
6. ON/OFF –switching
the device on and off
(red – status indicator).
7. MENU –
Settings menu.
8. REC/SNAP –control
the recording mode /
features selection when
navigating the menu.
9. Battery slot cover
10. DOWN – down (navigating
(navigating
different menus, reducing
exposure settings EV).
11. UP – up
different menus, increasing
exposure settings EV).
12. MODE – mode selection
(«video», «photo»,
«archive mode»).
13. Mounting hole.
14. Power socket.
15. USB – PC connection.
16. HDMI – HDMI video output.
17. 2.5" rotatable display.
270º
(SD Slot - located under
the battery slot cover).
Do not insert or remove
your SD memory card
when the power or
indicator lights are on.

7
ENG
Package contents
Gazer H521 MVR Warranty Card User Manual
Battery 40C
3,7V 500mAh
Vacuum windshield
mount
3M scotch tape mount
USB-cable
for PC connection
Memory Card
Gazer micro SDHC
+ adapter
Cigarette lighter
socket power unit
(with an integrated
+ 5V converter)
Controls
1. IR diodes.
2. Lens.
3. Status indicator
(blue – operation mode,
red – charging mode).
4. Microphone.
5. Speaker.
6. ON/OFF –switching
the device on and off
(red – status indicator).
7. MENU –
Settings menu.
8. REC/SNAP –control
the recording mode /
features selection when
navigating the menu.
9. Battery slot cover
10. DOWN – down (navigating
(navigating
different menus, reducing
exposure settings EV).
11. UP – up
different menus, increasing
exposure settings EV).
12. MODE – mode selection
(«video», «photo»,
«archive mode»).
13. Mounting hole.
14. Power socket.
15. USB – PC connection.
16. HDMI – HDMI video output.
17. 2.5" rotatable display.
270º
(SD Slot - located under
the battery slot cover).
Do not insert or remove
your SD memory card
when the power or
indicator lights are on.

ENG
8
Usage
.
•
Note:
•When the power is on, the status indicator (3) stays blue and
starts flashing when the recording mode is activated. When the
MVR is charging, the status indicator flashes red (3). In case the
device is fully charged or no power is supplied, the indicator (3)
stays off. To determine the status of the device you can either use
the status indicator or check the display icons.
•The MVR starts recording automatically when the power is on,
there is no need to press REC/SNAP button manually (8).
•The MVR automatically shuts down, saves the video and switches
off when no power is supplied. Manual shutdown (before you
turn off the ignition) is not required. If necessary, you can
manually turn off the MVR by long pressing the ON/OFF button
(6). Use the same button to turn it back on.
You can change the camera exposure in the recording mode by
pressing the UP/DOWN button.
Do not turn off the recorder manually if it is in the recording
mode (this may damage the last recording). First stop the recording
and then turn off the device.
The MVR can operate independently for a certain period of time.
The offline operation time depends on the status and charge of
the removable battery.
Recommendation: Use the recording mode with a minimum video
length (2 minutes). In this case, the pauses between videos will be
minimal. The longer the videos are, the longer are the pauses
between them.
Preparing Memory Card
Before using the MVR, it is important to format your memory card
using specialized tools. We recommend using a free SD Formatter
utility. Use a search engine to find and download it from one of many
Internet resources or from the web portal http://www.sdcard.org.
Formatting is necessary to optimize the memory card access
speed. The system formats the card in accordance with SD Memory
Card Format Specification what allows the MVR to access the card
faster. This cannot be done with regular Windows formatting tools.
SD Formatter also (by selecting option of Format Size Adjustment
= ON) creates an optimal file system structure (cluster size, etc.).
If you use an unformatted memory card, the MVR may fail to record
or record incorrectly (long pauses between videos). Formatting
with SD Formatter reduces the duration of pauses to a minimum.

9
ENG
Usage
.
•
Note:
•When the power is on, the status indicator (3) stays blue and
starts flashing when the recording mode is activated. When the
MVR is charging, the status indicator flashes red (3). In case the
device is fully charged or no power is supplied, the indicator (3)
stays off. To determine the status of the device you can either use
the status indicator or check the display icons.
•The MVR starts recording automatically when the power is on,
there is no need to press REC/SNAP button manually (8).
•The MVR automatically shuts down, saves the video and switches
off when no power is supplied. Manual shutdown (before you
turn off the ignition) is not required. If necessary, you can
manually turn off the MVR by long pressing the ON/OFF button
(6). Use the same button to turn it back on.
You can change the camera exposure in the recording mode by
pressing the UP/DOWN button.
Do not turn off the recorder manually if it is in the recording
mode (this may damage the last recording). First stop the recording
and then turn off the device.
The MVR can operate independently for a certain period of time.
The offline operation time depends on the status and charge of
the removable battery.
Recommendation: Use the recording mode with a minimum video
length (2 minutes). In this case, the pauses between videos will be
minimal. The longer the videos are, the longer are the pauses
between them.
Preparing Memory Card
Before using the MVR, it is important to format your memory card
using specialized tools. We recommend using a free SD Formatter
utility. Use a search engine to find and download it from one of many
Internet resources or from the web portal http://www.sdcard.org.
Formatting is necessary to optimize the memory card access
speed. The system formats the card in accordance with SD Memory
Card Format Specification what allows the MVR to access the card
faster. This cannot be done with regular Windows formatting tools.
SD Formatter also (by selecting option of Format Size Adjustment
= ON) creates an optimal file system structure (cluster size, etc.).
If you use an unformatted memory card, the MVR may fail to record
or record incorrectly (long pauses between videos). Formatting
with SD Formatter reduces the duration of pauses to a minimum.

ENG
10
Preparing MVR
18:54:122012/01/08
EV +0
Loop
recording
Recording time
00:24:19
1080Р
Memory card
is inserted
Battery charge
indicator
Recording quality
Mode
Exposure
Date and time captions
(shown in the video)
Recording
mode indicator
One must adjust the MVR settings before using the device. The main
settings are optimal by default (factory settings) but in any case,
you must set the exact time and date. This is necessary for correct
functioning in the recording mode and further analysis of recorded
video sequences.
1. Do not connect the MVR to the power supply yet. First make sure
that all the indicators are off and then insert the memory card.
The memory card is inserted with connectors towards the
display.
2. Connect the recorders’ power unit to the car’s cigarette lighter
socket and supply the power. When you turn on the MVR, it
automatically switches to the recording mode. That is why you
will see the real time camera image at once (loop-through
channel) and the recording mode indicator will light up.
3. Press the REC/SNAP button to stop the recording first, if you
want to go to the setup menu (the recording mode will take some
time to shut down as it is closing and saving the current file) and
then press the MENU button.
4. Use UP and DOWN buttons to navigate through the menu,
REC/SNAP to go to the submenu, and MENU button to go back.
Preparing MVR
Main window icons definition
Settings menu
Following icons can be found in the settings menu.
18:54:122012/01/08
EV +0
Loop
recording
Recording time
00:24:19
1080Р
Memory card
is inserted
Battery charge
indicator
Recording quality
Motion
detection
Mode
Exposure
Date and time captions
(shown in the video)
1/4
Date StampResolution
2/4
3/4
Lamp setting
4/4
Video settingsVideo settings
SettingsSettings
Loop recording
Motion Detection
Record Audio
Format
Default Setting
Software version
Date/Time
Beep Sound
Language
Frequency

11
ENG
Preparing MVR
18:54:122012/01/08
EV +0
Loop
recording
Recording time
00:24:19
1080Р
Memory card
is inserted
Battery charge
indicator
Recording quality
Mode
Exposure
Date and time captions
(shown in the video)
Recording
mode indicator
One must adjust the MVR settings before using the device. The main
settings are optimal by default (factory settings) but in any case,
you must set the exact time and date. This is necessary for correct
functioning in the recording mode and further analysis of recorded
video sequences.
1. Do not connect the MVR to the power supply yet. First make sure
that all the indicators are off and then insert the memory card.
The memory card is inserted with connectors towards the
display.
2. Connect the recorders’ power unit to the car’s cigarette lighter
socket and supply the power. When you turn on the MVR, it
automatically switches to the recording mode. That is why you
will see the real time camera image at once (loop-through
channel) and the recording mode indicator will light up.
3. Press the REC/SNAP button to stop the recording first, if you
want to go to the setup menu (the recording mode will take some
time to shut down as it is closing and saving the current file) and
then press the MENU button.
4. Use UP and DOWN buttons to navigate through the menu,
REC/SNAP to go to the submenu, and MENU button to go back.
Preparing MVR
Main window icons definition
Settings menu
Following icons can be found in the settings menu.
18:54:122012/01/08
EV +0
Loop
recording
Recording time
00:24:19
1080Р
Memory card
is inserted
Battery charge
indicator
Recording quality
Motion
detection
Mode
Exposure
Date and time captions
(shown in the video)
1/4
Date StampResolution
2/4
3/4
Lamp setting
4/4
Video settingsVideo settings
SettingsSettings
Loop recording
Motion Detection
Record Audio
Format
Default Setting
Software version
Date/Time
Beep Sound
Language
Frequency

ENG
12
Settings menu
Resolution
VGA 640x480 HD 1280x720 FHD 1920x1080 int.
Specifies the resolution of recorded videos.
Loop recording
2 MIN 5 MIN 10 MIN OFF
Motion Detection
OFF ON
OFF ON
OFF ON
Record Audio
Date/Time
Sets date and time.
Beep Sound
Language Selects the menu language.
Frequency
50 Hz 60 Hz
It is recommended record 1280x720, 30 fps mode if
you use 8-32Gb memory cards.
Built-in video camera setting.
The recommended frequency for USA is 60 HZ.
The recommended frequency for Europe is 50 HZ.
Setting the length of recorded videos.
We recommend using the recording mode with a
minimum video length (2 minutes). In this case, the
pauses between videos will be minimal.
Uses motion detection to turn the recording mode
on and off.
We recommend against enabling this mode when the
vehicle is in motion. You can use the motion detector
when the car is parked for a long time.
Turns the built-in microphone on/off.
We recommend keeping the sound recording mode
enabled at all times. In case of a controversial traffic
situation, it will provide additional information.
We recommend that you use accurate date and time
settings and check them periodically.
We recommend that you use accurate date and time
settings and check them periodically. Date format
used: DD / MM / YYYY (day / month / year), MM / DD /
YYYY, YYYY / MM / DD. Time format used: 24 hours.
Settings menu/Viewing records
Lamp setting
Auto OFF
Infrared lights mode settings.
Format
Execute
Formatting the memory card.
Default Setting Execute
Restart the system with factory settings.
Display the MVR firmware version.Software version
Viewing records
MVR viewing
In the «Auto» mode, the lights turn ON/OFF
automatically, depending on the lighting conditions.
You can turn off the infrared lights completely by
pressing «OFF» button. We recommend keeping
these lights off when driving. You can enable this
option when the vehicle is parked.
Formatting the memory card.
5. After the settings have been adjusted, do not forget to resume
the recording by pressing the REC/SNAP button.
6. Mount the MVR on the windshield and connect it to a power
supply.
You can view the records directly from the MVR. Other options are:
connect the MVR to your personal computer with the USB cable that
comes in the package or remove the memory card and insert it
directly into your PC.
Stop the current recording by pressing the REC/SNAP button, then
switch to the «View» mode using the MODE button (double-click).
To navigate through your videos use UP and DOWN buttons.
The REC/SNAP button will start and pause playback.
In the «View» mode, one can use the MENU button to access the
deletion, video file protection and slideshow submenu.
Use MODE button to exit from the viewing mode. When you finish
viewing, do not forget to resume the recording by pressing the
REC/SNAP button.

13
ENG
Settings menu
Resolution
VGA 640x480 HD 1280x720 FHD 1920x1080 int.
Specifies the resolution of recorded videos.
Loop recording
2 MIN 5 MIN 10 MIN OFF
Motion Detection
OFF ON
OFF ON
OFF ON
Record Audio
Date/Time
Sets date and time.
Beep Sound
Language Selects the menu language.
Frequency
50 Hz 60 Hz
It is recommended record 1280x720, 30 fps mode if
you use 8-32Gb memory cards.
Built-in video camera setting.
The recommended frequency for USA is 60 HZ.
The recommended frequency for Europe is 50 HZ.
Setting the length of recorded videos.
We recommend using the recording mode with a
minimum video length (2 minutes). In this case, the
pauses between videos will be minimal.
Uses motion detection to turn the recording mode
on and off.
We recommend against enabling this mode when the
vehicle is in motion. You can use the motion detector
when the car is parked for a long time.
Turns the built-in microphone on/off.
We recommend keeping the sound recording mode
enabled at all times. In case of a controversial traffic
situation, it will provide additional information.
We recommend that you use accurate date and time
settings and check them periodically.
We recommend that you use accurate date and time
settings and check them periodically. Date format
used: DD / MM / YYYY (day / month / year), MM / DD /
YYYY, YYYY / MM / DD. Time format used: 24 hours.
Settings menu/Viewing records
Lamp setting
Auto OFF
Infrared lights mode settings.
Format
Execute
Formatting the memory card.
Default Setting Execute
Restart the system with factory settings.
Display the MVR firmware version.Software version
Viewing records
MVR viewing
In the «Auto» mode, the lights turn ON/OFF
automatically, depending on the lighting conditions.
You can turn off the infrared lights completely by
pressing «OFF» button. We recommend keeping
these lights off when driving. You can enable this
option when the vehicle is parked.
Formatting the memory card.
5. After the settings have been adjusted, do not forget to resume
the recording by pressing the REC/SNAP button.
6. Mount the MVR on the windshield and connect it to a power
supply.
You can view the records directly from the MVR. Other options are:
connect the MVR to your personal computer with the USB cable that
comes in the package or remove the memory card and insert it
directly into your PC.
Stop the current recording by pressing the REC/SNAP button, then
switch to the «View» mode using the MODE button (double-click).
To navigate through your videos use UP and DOWN buttons.
The REC/SNAP button will start and pause playback.
In the «View» mode, one can use the MENU button to access the
deletion, video file protection and slideshow submenu.
Use MODE button to exit from the viewing mode. When you finish
viewing, do not forget to resume the recording by pressing the
REC/SNAP button.

ENG
14
Viewing records
Settings menu in the photo shooting mode
Capture Mode
Resolution
Sequence
Quality
Sharpness
White Balance
Color
ISO
Face Detection
Anti-Shaking
Quick Review
Date Stamp
Use the MODE button to switch to the photo shooting mode and
take a snapshot by pressing the REC/SNAP button. Use the MODE
button to exit from the viewing menu.
Vacuum mount installation
Disengaging the frame
from the mount
Press on
the tab
Disconnect
the recorder
from the moun
You can rotate the recorder
in any direction around its axis.
To remove the MVR from
the mount, follow the steps
shown in the drawing.
Connect the frame of the device
with the mount.
Install the MVR and fix
the power supply cable as shown
in the drawing.
Until click
1
3 4
360 ° rotation
2
Recommendation: Install your MVR as high as possible (MVR
frame right next to the rear view mirror or behind it) in the
position in which the lens is titled slightly downward at an angle
of about 15°. If the MVR is mounted too low (on the dashboard
or a bit higher), the recorded videos will not provide full informa-
tion about the road situation because it is impossible to see the
front of your vehicle, therefore there is no «reference point».
Recordings will be significantly dimmed if the device is mounted
in parallel with the road or at an upward angle.

15
ENG
Viewing records
Settings menu in the photo shooting mode
Capture Mode
Resolution
Sequence
Quality
Sharpness
White Balance
Color
ISO
Face Detection
Anti-Shaking
Quick Review
Date Stamp
Use the MODE button to switch to the photo shooting mode and
take a snapshot by pressing the REC/SNAP button. Use the MODE
button to exit from the viewing menu.
Vacuum mount installation
Disengaging the frame
from the mount
Press on
the tab
Disconnect
the recorder
from the moun
You can rotate the recorder
in any direction around its axis.
To remove the MVR from
the mount, follow the steps
shown in the drawing.
Connect the frame of the device
with the mount.
Install the MVR and fix
the power supply cable as shown
in the drawing.
Until click
1
3 4
360 ° rotation
2
Recommendation: Install your MVR as high as possible (MVR
frame right next to the rear view mirror or behind it) in the
position in which the lens is titled slightly downward at an angle
of about 15°. If the MVR is mounted too low (on the dashboard
or a bit higher), the recorded videos will not provide full informa-
tion about the road situation because it is impossible to see the
front of your vehicle, therefore there is no «reference point».
Recordings will be significantly dimmed if the device is mounted
in parallel with the road or at an upward angle.

ENG
16
3M scotch tape mount installation
Warning!
1 2
3 4
5
Unscrew the nut of the
vacuum mount and detach the lower
and upper parts.
Use the screw and the nut from
package to securely attach
both parts.
Connect the bottom of the vacuum
mounting with 3M scotch tape.
Attach the frame of the recorder
to the 3M scotch tape mounting.
Wipe the surface of the windshield before installing.
Make sure the place is dry and clean. Do not install the mount on
3M scotch tape at temperature below +5°C. Because of such low
temperature and the difference between the temperature inside
the car and outdoors, the 3M scotch will lose its adhesive proper-
ties and will not be able to fix the mount properly.
Prior to installing, determine the exact
MVR position on the windshield. Mark
the installation place. Remember that
once the mount is installed on the car
windshield, you cannot change the
horizontal position of the device (side
to side), only vertical position (up and
down) can be changed afterwards.
Should your package include a single wide strip of 3M
scotch tape instead of 4 narrow ones, please follow the
installation instructions provided above.
Note:
3M scotch tape mount installation
Make sure that the device is installed
in a position from which hit can
be conveniently removed later.
Fix the mount so that other objects
do not prevent you from easily
removing your recorder.
Attach the 3M tape on the mount
by removing the protective film
on one side of 3M tape.
Double check that you have chosen
the best location to install the mount.
Remove the second protective film
from the 3M tape.
Attach the 3M mount to the recorder
on the windshield.
To remove the 3M tape mounting
from the windshield, take a ruler
or a credit card and push it gently
between the mount and the windshield.

17
ENG
3M scotch tape mount installation
Warning!
1 2
3 4
5
Unscrew the nut of the
vacuum mount and detach the lower
and upper parts.
Use the screw and the nut from
package to securely attach
both parts.
Connect the bottom of the vacuum
mounting with 3M scotch tape.
Attach the frame of the recorder
to the 3M scotch tape mounting.
Wipe the surface of the windshield before installing.
Make sure the place is dry and clean. Do not install the mount on
3M scotch tape at temperature below +5°C. Because of such low
temperature and the difference between the temperature inside
the car and outdoors, the 3M scotch will lose its adhesive proper-
ties and will not be able to fix the mount properly.
Prior to installing, determine the exact
MVR position on the windshield. Mark
the installation place. Remember that
once the mount is installed on the car
windshield, you cannot change the
horizontal position of the device (side
to side), only vertical position (up and
down) can be changed afterwards.
Should your package include a single wide strip of 3M
scotch tape instead of 4 narrow ones, please follow the
installation instructions provided above.
Note:
3M scotch tape mount installation
Make sure that the device is installed
in a position from which hit can
be conveniently removed later.
Fix the mount so that other objects
do not prevent you from easily
removing your recorder.
Attach the 3M tape on the mount
by removing the protective film
on one side of 3M tape.
Double check that you have chosen
the best location to install the mount.
Remove the second protective film
from the 3M tape.
Attach the 3M mount to the recorder
on the windshield.
To remove the 3M tape mounting
from the windshield, take a ruler
or a credit card and push it gently
between the mount and the windshield.

Specifications
Camera angle
120°
Recording resolution
Camera rotation ability
Device rotation ability
Video specification Video Codec: MJPEG, format: AVI
Sound recording Yes
Mute Yes, using the menu
USB interface Yes
HDMI video output Yes
Display 2,5" rotatable
Memory card support SDHC up to 32 GB
Memory card included Yes, Gazer micro SDHC + adapter
Date and time display
Yes
Auto start on power up
Yes, in the recording mode
Glass mount type Vacuum, 3M scotch tape
Power 5V, PSU 12-24V connection to the car’s
cigarette lighter socket
Dimensions, mm 98x63x29
Weight, gram 102
Resolution Memory card capacity
640x480, (30 FPS) 66 min
min
min
1280x720, (30 FPS) 22
1920x1080i, (30 FPS) 9
1GB memory recording time
VGA 640x480, 30 fps. HD 1280x720,
30 fps. (FHD mode 1920x1080, 30 fps
achieved by software interpolation)
Содержание
1. Меры предосторожности .................................................20
2. Важная информация .......................................................21
3. Комплектация ................................................................22
4. Элементы управления ..................................................... 23
5. Особенности использования модели ................................. 24
6. Подготовка карты памяти ................................................25
7. Подготовка видеорегистратора . ....................................... 26
• Обозначение пиктограмм основного окна . ..................... 27
• Меню настроек ............................................................27
8. Меню настроек . .............................................................. 28
9. Просмотр записей ...........................................................29
• Просмотр из меню регистратора ...................................29
• Режим фотосъемки . ..................................................... 30
10. Установка вакуумного крепления ...................................31
11. Установка крепления на 3М скотче ................................. 32
12. Технические характеристики .........................................33
• Время записи на 1GB памяти ........................................ 34
ENG
18

Specifications
Camera angle
120°
Recording resolution
Camera rotation ability
Device rotation ability
Video specification Video Codec: MJPEG, format: AVI
Sound recording Yes
Mute Yes, using the menu
USB interface Yes
HDMI video output Yes
Display 2,5" rotatable
Memory card support SDHC up to 32 GB
Memory card included Yes, Gazer micro SDHC + adapter
Date and time display
Yes
Auto start on power up
Yes, in the recording mode
Glass mount type Vacuum, 3M scotch tape
Power 5V, PSU 12-24V connection to the car’s
cigarette lighter socket
Dimensions, mm 98x63x29
Weight, gram 102
Resolution Memory card capacity
640x480, (30 FPS) 66 min
min
min
1280x720, (30 FPS) 22
1920x1080i, (30 FPS) 9
1GB memory recording time
VGA 640x480, 30 fps. HD 1280x720,
30 fps. (FHD mode 1920x1080, 30 fps
achieved by software interpolation)
Содержание
1. Меры предосторожности .................................................20
2. Важная информация .......................................................21
3. Комплектация ................................................................22
4. Элементы управления ..................................................... 23
5. Особенности использования модели ................................. 24
6. Подготовка карты памяти ................................................25
7. Подготовка видеорегистратора . ....................................... 26
• Обозначение пиктограмм основного окна . ..................... 27
• Меню настроек ............................................................27
8. Меню настроек . .............................................................. 28
9. Просмотр записей ...........................................................29
• Просмотр из меню регистратора ...................................29
• Режим фотосъемки . ..................................................... 30
10. Установка вакуумного крепления ...................................31
11. Установка крепления на 3М скотче ................................. 32
12. Технические характеристики .........................................33
• Время записи на 1GB памяти ........................................ 34
19
RU

Gazer H521
Поздравляем Вас с приобретением автомобильного
видеорегистратора Gazer.
Перед использованием прибора, пожалуйста,
внимательно ознакомьтесь с данным руководством.
Меры предосторожности
• Избегайте воздействия н а видеорегистратор прямых солнечных
лучей.
• Не используйте химические средства для чистки устройства.
Пожалуйста, используйте мягкую ткань для очистки корпуса
и линзы.
• Избегайте ударов, падений и механических повреждений
прибора.
• Не используйте и не храните прибор в слишком холодных или
горячих местах.
- Температура хранения: от -20°С до +40°С
- Температура использования: от +5°С до +40°С
• В случае, если оборудование в течение продолжительного
времени находилось в условиях низкой температуры, перед
подключением и запуском обязательно прогрейте его до
температуры эксплуатации.
• Не пытайтесь ремонтировать видеорегистратор самостоятельно.
В случае возникновения каких-либо поломок, обратитесь к
продавцу или в сервисный центр.
• Завод-изготовитель и продавец не несут ответственности
за убытки, возникшие в результате использования
видеозаписей и данных, полученных при помощи настоящего
видеорегистратора.
Важная информация
• Не вставляйте и не вынимайте SD-карту памяти при
подключенном питании либо при работе прибора от съемного
аккумулятора. Это может привести к нарушениям в работе
видеорегистратора. Перед установкой либо изъятием карты
памяти убедитесь, что питание прибора было отключено не
менее 30 секунд назад, а все индикаторы регистратора погасли
не менее 10 секунд назад.
• Перед началом эксплуатации обязательно проведите точную
настройку даты и времени, так как в случае некорректных
установок даты и времени видеорегистратор может не
производить запись.
• Интервал времени между нажатиями кнопок управления
должен быть не менее 0,5 секунды. В противном случае
видеорегистратор может потребовать перезагрузки с помощью
извлечения аккумулятора из видеорегистратора.
• Внимательно подключайте кабель питания к устройству. Не
перепутайте кабель питания видеорегистратора с кабелем
питания радар - детектора или навигатора, которые могут
иметь напряжение питания +12В. В случае такого подключения
устройство может выйти из строя.
• После подключения кабеля питания прибора, не отключайте
питание как минимум 20 секунд. Это необходимо для корректной
работы схемы заряда аккумуляторов.
• Если после запуска двигателя при подключенном кабеле
питания регистратор не перешел в режим записи, отключите
кабель питания на 10 секунд , затем подключите его снова.
• Используйте перезагрузку с помощью извлечения аккумулятора
при отключенном кабеле питания в следующих случаях:
• при подключении кабеля питания не загорается индикатор
питания;
• устройство не переходит из режима ожидания в режим записи
или управления;
• поведение устройства не соответствует заданным режимам.
• Для перезагрузки видеорегистратора отключите подачу питания
на видеорегистратор, снимите крышку отсека аккумулятора
(стр. 23, п. 9) и аккуратно извлеките аккумулятор из отсека не
менее чем на 5 секунд. После этого установите аккумулятор на
место, закройте крышку и подайте на регистратор питание.
Внимание!
RU
20