GCC Technologies EP-60 User manual

V.12 2014 Mar.
Expert Pro Series
User Manual
http://www.GCCworld.com

V.12 2014 Mar.
NOTICE
GCC reserves the right to modify the information contained in this user
manual at any time without prior notice; un-authorized modification, copying
distribution or display is prohibited. All comments, queries or
suggestions concerning this manual please consult with your local dealer.

Expert Pro User Manual
Important Information
I
I
Im
m
mp
p
po
o
or
r
rt
t
ta
a
an
n
nt
t
t I
I
In
n
nf
f
fo
o
or
r
rm
m
ma
a
at
t
ti
i
io
o
on
n
n
PRECAUTIONS IN USE
For safety concern, please always hold the cutter firmly from the bottom
when moving it. Do not move the cutter by clasping the depression area on
both sides.
Do not shake or drop the blade holder, a blade tip maybe fly out.
During operation, keep away from any moving parts of the cutter (such as
the carriage, drums). Also be careful that your clothing and hairs do not be
caught.
Always connect the power cable to a grounded outlet.
Always use the accessory power cable that is provided. Do not wire the
power cable so that it becomes bent or caught between objects.
Do not connect the power cable to branching outlet to which other
machines are also connected, or use an extension cable. There is danger
of overheating and of misoperation of the machine.
Keep the tools away from children where they can reach.
Always put the pinch rollers within position of the white marks.
Thanks for your purchase of GCC Expert Pro Cutting Plotter. For
your safety and to optimize the performance of the Expert Pro,
please read the user manual completely and keep it in a correct
location.

Expert Pro User Manual
Contents
C
Co on nt te en nt ts s
Important Information
1. General Information
1.1 Introduction 1-1
1.2 Package Items 1-1
1.3 Product Features 1-2
1.4 Appearance of Expert Pro 1-3
1.4.1 Front View of Expert Pro 1-4
1.4.2 Back View of Expert Pro 1-4
1.4.3 The Whole View of Expert Pro 1-4
1.4.4 The Left-hand Side of Expert Pro 1-5
1.4.5 The Right-hand Side of Expert Pro 1-5
2. Installation
2.1 Precaution 2-1
2.2 Stand & Flexible Media Support System 2-2
2.2.1 Stand Installation (for EP-60) 2-2
2.2.2 Stand & Flexible Media Support System (for EP-132S) 2-5
2.3 Desktop Support Brackets 2-10
2.4 Blade Installation 2-12
2.5 Instruction of Damper Roller 2-15
2.6 Cable Connections 2-16
2.6.1 USB Interface 2-16
2.6.2 Driver Un-installation 2-20
2.6.3 How to switch the USB mode? 2-23
2.6.4 RS-232 Interface 2-23
2.6.5 Data Transmitting 2-23
2.6.6 Printer Sever Shared Setting 2-24
3. The Control Panel
3.1 The LCD Panel 3-1
3.2 Menu in On-line Mode 3-2
3.3 Menu in Off-line Mode 3-3
3.4 Menu Items 3-4
4. Operation
4.1 Media Loading 4-1
4.1.1 Loading the Sheet Media 4-1
4.1.2 Loading the Roll Media 4-3
4.2 Tracking Performance 4-6
4.3 Cutting Force and Offset Adjustment 4-7
4.4 When Completing the Cutting Job 4-9
4.5 Expert Pro Print Driver setting 4-10
4.5.1 Option Page 4-10
4.6 Reference Parameter setting for different materials 4-12
5. Maintenance
5.1 Cleaning the cutting Plotter 5-1

Expert Pro User Manual
Contents
5.2 Cleaning the Grid Drum 5-2
5.3 Cleaning the Pinch Rollers 5-2
6. Trouble Shooting
6.1 Non-Operational Problems 6-1
6.2 Operational Problems 6-2
6.3 Communication Problems 6-3
6.4 Software Problems 6-4
6.5 Cutting Quality Problems 6-5
Appendix
A-1
Specifications of Expert Pro A-1
A-2
Blade Specification A-2
A-3
CorelDraw Instruction A-3
A-4 DirectCut A-4

Expert Pro User Manual
General Information 1-1
Chapter 1 General Information
1.1 Introduction
Expert Pro series cutting plotters have been designed to produce computer-generated images
on sheets or rolls of vinyl media.
This manual covers the following models of Expert Pro series cutting plotters:
‧EP-60 for media width: 70mm(2.76”) ~ 719mm(28.3”)
‧EP-132S for media width: 70mm(2.76”) ~ 1470mm(57.87”)
1.2 Package Items
The package of the Expert Pro model contents the items listed below, please check carefully.
If you find any item missing, please consult your local dealer for further assistance.
S
St ta an nd da ar rd d I It te em m Q Qu ua an nt ti it ty y
1. Cutting Plotter 1
2. Stand Set ( Optional for EP-60 )
1 Left side vertical stand
1 Right side vertical stand
1 Support for left side
1 Support for right side
1 Stand Beam
2 Bottom Stands with wheels
2 Sliding brackets for paper takeup
1 Hex Wrench (M5)Φ4
28 Socket flat head screws(M6*12L)
1 Installation Guide
1
2. Stand Set ( for EP-132S )
2 piece of T-shape stand
1 piece of stand beam
18 pieces of M6 screws
1 piece of M5 L-shape hexagon screw driver
1 piece of Installation Guide for Stand Set
1

Expert Pro User Manual
General Information 1-2
3. Flexible Media Support System Package
Items EP-60 EP-132S
1 set of Roll Media Flange (2 pieces) V
1 set of Roll Holder (2 pieces) V
1 set of Roll Holder Guide Bushes (4 pieces) V
1 set of Roll Holder Support (2 pieces) V
32 pieces of M6 screws V
1 piece of M6 L-shape hexagon screw driver V
1 piece of Roll Base V
1
4. Accessories
1 piece of User’s Compact Disk
1 piece of AC power Cord
1 pieces of data cable (Print cable)
1 pieces of data cable (USB cable: 1.8m)
1 set of Blade Holder Assembly (Installed in tool carriage of the cutting
plotter )
1 piece of Blade (Installed in Blade Holder)
1 piece of Safe Blade
1 piece of Cutting Pad
1 piece of Tweezers
1 piece of Promise Card
1
1.3 Product Features
The following are the main features of the Expert Pro series cutting plotters:
‧Dual-port connectivity provides you with greater flexibility.
‧Up to 400-gram cutting force.
‧Up to 600mm/per second cutting speed.
‧Guaranty 5-meter tracking.
‧User-friendly, multi-language control panel

Expert Pro User Manual
General Information 1-3
1.4 Appearance of Expert Pro
1.4.1 The Front View (Figure 1-1)
Control Panel
14 buttons and 1
LED and 1 LCM
showing messages
and menus.
Cutting Pad
provides the protection of
blade when the blade is
cutting.
Tool Carriage
performs the
cutting with the
installed blade or
pen.
Alignment Rulers
media can be aligned
with the clear guide line
marks
Grid Drums
move the media back and
forth during operation.
Slicer Groove
cuts off the extra
media easily along
this groove.
Platen
provides the surface for
supporting media while
cutting
Figure 1-1

Expert Pro User Manual
General Information 1-4
1.4.2 The Back View (Figure 1-2)
1.4.3 The Whole View (Figure 1-3)
** The Expert Pro model comes with a standard stand
Pinch Rollers
hold the media during cutting.
Lever
raises or lowers
the pinch rollers.
Figure 1-2
Figure 1-3
Roll Holder
h
olds and supplies the
roll media for cutting.
Stand Beam
stabilizes the body.
Roll Holder
Support
supports roll holders
T-Stand – supports
the cutting plotter
T-Stand – supports
the cutting plotter

Expert Pro User Manual
General Information 1-5
1.4.4 The Left-hand Side of Expert Pro (Figure 1-4)
1.4.5 The Right-hand Side of Expert Pro (Figure 1-5)
Fuse – 3 Amp.
AC Power Connector
Power Switch – On when switches to [I]; Off to [O]
Figure 1-4
Serial Interface Connector (RS232C)
used to connect the cutting plotter to a
computer through a serial interface cable.
Figure 1-5
USB Connector
used to connect the cutting plotter to a
computer through a USB cable.

Expert Pro User Manual
Installation 2-1
Chapter 2 Installation
2.1 Precaution
Notice 1
Carefully handle the cutter to prevent any injuries.
Make sure the power switch is off before installing the cutting plotter.
Notice 2 A proper place for installation the cutting plotter
Please select a proper location that meets the following conditions.
The machine can be approached easily from any direction.
Keep at least 60 cm space in front and behind the machine.
Make sure the cutter is placed on a flat, level and sturdy surface
The operation temperature should be between 15℃to 30℃(60
o
F ~ 86
o
F)
in the workshop.
The relative humidity of the working environment should be between 25% to
75%.
Protecting the machine from dust and air current.
Preventing the machine from direct sunlight.
Notice 3 Connecting the Power Supply
Check the plug of the power cord to see if it matches the wall outlet. If not,
please contact your dealer.
Insert the plug (male) into a grounded power outlet.
Insert the other end (female) of power cord into the AC connector of cutting
plotter.

Expert Pro User Manual
Installation 2-2
2.2 Stand & Flexible Media Support System
2.2.1 Stand Installation（
（（
（Optional for EP-60）
））
）
Please follow the procedures below for assembling the stand and the media
support system.
Step 1 Please examine the supplied items in the accessory box of the stand carton
before you install:
Item List：
：：
：
1 Left side vertical stand
1 Right side vertical stand
1 Support for left side
1 Support for right side
1 Stand Beam
2 Bottom Stands with wheels
2 Sliding brackets for paper takeup
1 Hex Wrench (M5)Φ4
28 Socket flat head screws(M6*12L)
1 Installation Guide
Step 2
Position the Left side vertical stand perpendicularly to part and put the
screws into the holes and tighten them to form a left side T-stand (Figure 2-1).
Repeat the same steps with the Right side vertical stand.
Figure 2-1

Bottom Stand with wheels
Left side vertical stand

Expert Pro User Manual
Installation 2-3
Step 3
Place the stand beam upright on the T-stand and put the screws into the holes
but do not tighten them at this step.
Step 4
Position both the left Support and right Support perpendicularly to the T-stand
and put the screws into the holes and tighten them as shown in Figure 2-3.
T-stand
Stand Beam
Figure 2-2
Figure 2-3
Support for left side
Support for right side

Expert Pro User Manual
Installation 2-4
Step 5
Remove the cutting plotter from the carton. Position the stand under the plotter,
and insert the screws into the holes on the bottom of the plotter but do not
tighten them up as shown in Figure 2-4.
Step 6
Tighten the screws of step 3 and step 5. Place the sliding brackets for paper
takeup onto the stand beam.
Figure 2-4
Figure 2-5
sliding brackets for paper takeup

Expert Pro User Manual
Installation 2-5
2.2.2 Stand Installation(for EP-132S)
Please follow procedure below to assemble stand and media support system.
Step 1 Please examine supplied items in the accessory box of stand carton before you
install:
Item List：
：：
：
 2 piece of T-shape stand
 1 piece of stand beam
 18 pieces of M6 screws
 1 piece of M5 L-shape hexagon screw driver
 1 piece of Installation Guide for Stand Set
Step 2
 Remove the plotter body and the accessories from the shipped carton.
 Place the stand beam upright on the T-stand and follow the number
 to assemble.
(See Figure 2-6 & 2-7)
Step 3
Position the stand beam perpendicularly to part and put the screws into the
holes and tighten them as Figure 2-7. Then the complete picture of stand will
be like Figure 2-6.

T-Stand
Stand beam
Figure 2-6
Figure 2-7

Expert Pro User Manual
Installation 2-6
Step 4
Remove the cutting plotter from the carton. Position your stand under the plotter,
and then insert the screws into the holes on plotter’s bottom and tighten them
up as shown in Figure 2-8.
Screws
Figure 2-8

Expert Pro User Manual
Installation 2-7
Step 5
Insert the roll holder support with the screws into the holes of the stand, and
then tighten them up as shown in Figure 2-9 . You could decide roll holder
support’s position by inserting into different holes.
Step 6
Place two roll holders onto the roll holder support and ensure the white
protrusion is wedged in the groove. ( Figure 2-10 )
3 screws
Roll holder
support
Figure 2-9
Roll holder support
Roll holder 1
Figure 2-10
Roll holder 2

Expert Pro User Manual
Installation 2-8
Step 7
Turn the screw counter-clockwisely for around three times after unpacking roll
holder 2
Step 8
Insert the end of the roll holder without the damper into the left roll holder
support and then insert the end of the roll holder with the damper into the right
roll holder support. Ensure the white protrusion is wedged in the groove.

Expert Pro User Manual
Installation 2-9
Step 9
Tighten the screw on the damper until it is securely attached to the right roll
holder support.
Step 10
Lastly, the complete picture will be shown like below. ( Figure 2-11 )
Figure 2-11

Expert Pro User Manual
Installation 2-10
2.3 Desktop Support Brackets
Step 1
Check three spacer supports on the back of the machine.
Step 2
Insert the left and right roll holder base into the spacer supports on the left and
right side when 2 inches roll media is used.