GCC Technologies P3-60 User manual

V.22 2016 Dec.
Puma III Series
User Manual
http://www.GCCworld.com

V.22 2016 Dec.
NOTICE
GCC reserves the right to modify the information contained in this user
manual at any time without prior notice; un-authorized modification, copying
distribution or display is prohibited. All comments, queries or
suggestions concerning this manual please consult with your local dealer.

Puma III User Manual
Important Information
Important Information
PRECAUTIONS IN USE
For safety concern, please always hold the cutter firmly from the bottom
when moving it. Do not move the cutter by clasping the depression area on
both sides.
Do not shake or drop the blade holder, a blade tip maybe fly out.
During operation, keep away from any moving parts of the cutter (such as
the carriage, drums). Also be careful that your clothing and hairs do not be
caught.
Always connect the power cable to a grounded outlet.
Always use the accessory power cable that is provided. Do not wire the
power cable so that it becomes bent or caught between objects.
Do not connect the power cable to branching outlet to which other
machines are also connected, or use an extension cable. There is danger
of overheating and of misoperation of the machine.
Keep the tools away from children where they can reach.
Always put the pinch rollers within position of the white marks.
Thanks for your purchase of GCC Puma III Cutting Plotter. For your safety
and to optimize the performance of the Puma III, please read the user
manual completely and keep it in a correct location.

Puma III User Manual
Contents
C
Co on nt te en nt ts s
Important Information
1. General Information
1.1 Introduction
1-1
1.2 Package Items
1-1
1.3Product Features
1-2
1.4 Appearance of Puma III
1-3
1.4.1 The Front View
1-3
1.4.2 The Back View
1-4
1.4.3 The Whole View
1-5
1.4.4 The Left-hand Side
1-6
1.4.5 The Right-hand Side
1-6
2. Installation
2.1 Precaution
2-1
2.2 Stand & Flexible Media Support System (for P3-132)
2-2
2.3 USB Cable Tie and Saddle
2-6
2.4Desktop Flexible Media Support System (for P3-60 only)
2-8
2.5Blade Installation
2-10
2.6Cable Connections
2-13
2.6.1 USB Interface
2-13
2.6.1.1 Connecting your GCC cutter
2-14
2.6.1.2 Installing the driver
2-14
2.6.1.3 Driver Un-installation
2-18
2.6.2 RS-232 Interface
2-21
2.6.3 Data Transmitting
2-21
2.6.4 Printer Sever Shared Setting
2-22
2.7Software Installation
2-25
2.7.1 GreatCut Installation
2-25
2.7.2 Sure Cuts A Lot Installation
2-31
2.7.2.1 Auto Installation
2-31
2.7.2.2 Manually Activate Software
2-35
2.7.2.3 Re-install Sure Cuts A Lot Software
2-36
3. The Control Panel
3.1 The LCD Panel
3-1
3.2Menu in On-line Mode
3-2
3.3 Menu in Off-line Mode
3-3
3.4 Menu Items
3-5
4. Operation
4.1 Media Loading
4-1
4.1.1 Loading the Sheet Media
4-1
4.1.2 Loading the Roll Media
4-3
4.2 Tracking Performance
4-6
4.3 Cutting Force and OffsetAdjustment
4-6
4.4 When Completing the Cutting Job
4-8
4.5 Puma III Print Driver setting
4-8
4.5.1 Puma III Print Driver setting>Option Page
4-8

Puma III User Manual
Contents
4.6 Reference Parameter setting for different materials
4-11
5. Automatic-Aligning System
5.1 Introduction
5-1
5.2 AAS Contour Cutting System
5-2
5.2.1 Notice for Registration Marks
5-2
5.2.2 AAS II on Puma III
5-3
5.3 Printer Test
5-4
5.4 Registration Mark Offset Range
5.5Contour Cutting
5-6
5-6
5.6Tips for AAS
5-8
6. Basic Maintenance
6.1 Cleaning the cutting Plotter
6-1
6.2 Cleaning the Grid Drum
6-2
6.3 Cleaning the Pinch Rollers
6-2
7. Trouble Shooting
7.1 Non-Operational Problems
7-1
7.2 Operational Problems
7-2
7.3 Communication Problems
7-3
7.4 Software Problems
7-4
7.5 Cutting Quality Problems
7-5
Appendix
A-1
Specifications of Puma III
A-1
A-2
Blade Specification
A-2
A-3
CorelDRAW Plug-In Instruction
A-3
A-4
Illustrator Plug-In Instruction
A-4
A-5
GreatCut Plug-In Instruction
A-5
A-6
SignPal 12 Instruction
A-6
A-7
Sure Cuts A Lot
A-7

Puma III User Manual
General Information 1-1
Chapter 1 General Information
1.1 Introduction
Puma III series cutting plotters have been designed to produce computer-generated images
or perform contour cutting on sheets or rolls of vinyl media.
This manual covers the following models of Puma III series cutting plotters:
‧P3-60 for media width: 70mm (2.76”) ~ 719mm (28.3”)
‧P3-132S for media width: 70mm (2.76”) ~ 1470mm (57.87”)
1.2 Package Items
The package of the Puma III model contents the items listed below, please check carefully.
If you find any item missing, please consult your local dealer for further assistance.
S
St ta an nd da ar rd d I It te em m Q Qu ua an nt ti it ty y
1. Cutting Plotter 1
2. Stand Set ( for P3-132S only, optional for P3-60)
2 piece of T-shape stand
1 piece of stand beam
20 pieces of M6 screws
1 piece of M5 L-shape hexagon screw driver
1 piece of Installation Guide for Stand Set
1
3. Flexible Media Support System Package
Items
P3-60
P3-132S
1 set of Roll Media Flange (2 pieces)
V
1 set of Roll Holder (2 pieces)
V
1 set of Roll Holder Guide Bushes (4 pieces)
V
1 set of Roll Holder Support (2 pieces)
V
32 pieces of M6 screws
V
1 piece of M6 L-shape hexagon screw driver
V
1 piece of Roll Base
V
1

Puma III User Manual
General Information 1-2
4. Accessories
1 piece of User’s Compact Disk
1 piece of AC power Cord
1 pieces of data cable (USB cable: 3m)
1 set of Blade Holder Assembly (Installed in tool carriage of the cutting
plotter )
1 piece of Blade (Installed in Blade Holder)
1 piece of Safe Blade
1 piece of Cutting Pad
1 piece of Tweezers

1 piece of Promise Card
1
1.3 Product Features
The following are the main features of the Puma III series cutting plotters:
‧Dual-port connectivity provides you with greater flexibility
‧Up to 400 gram cutting force
‧Up to 849 mm per second (33.4 ips) cutting speed (at 45° direction)
‧Guaranty 5-meter tracking
‧User-friendly and multi-language control panel
‧Enhanced Automatic-Aligning System for automatic contour cutting

Puma III User Manual
General Information 1-3
1.4 Appearance of Puma III
1.4.1 The Front View (Figure 1-1)
Control Panel
14 buttons and 1
LED and 1 LCM
showing messages
and menus.
Cutting Pad
provides the protection of
blade when the blade is
cutting.
Tool Carriage
performs the
cutting with the
installed blade or
pen with AAS
module.
Alignment Rulers
media can be aligned
with the clear guide line
marks
Grid Drums
move the media back and
forth during operation.
Slicer Groove
cuts off the extra
media easily along
this groove.
Platen
provides the surface for
supporting media while
cutting
Figure 1-1

Puma III User Manual
General Information 1-4
1.4.2 The Back View (Figure 1-2)
Pinch Rollers
hold the media during cutting.
Lever
raises or lowers
the pinch rollers.
Figure 1-2

Puma III User Manual
General Information 1-5
1.4.3 The Whole View (Figure 1-3)
**Stand for Puma III 60 is an optional item.
**Stand for Puma III 132S is a standard item.
Figure 1-3
Roll Holder – holds
and supplies the roll
media for cutting.
Roll Holder Guide
Bushes –serve to
keep the roll media in
place when media is
pulled from the roll.
T-Stand –supports
the cutting plotter
Stand Beam –
stabilizes the body.
Roll Holder
Support – supports
roll holders.
T-Stand –supports
the cutting plotter

Puma III User Manual
General Information 1-6
1.4.4 The Left-hand Side (Figure 1-4)
1.4.5 The Right-hand Side (Figure 1-5)
Fuse – 3 Amp.
AC Power Connector
Power Switch – On when switches to [I]; Off to [O]
Figure 1-4
Serial Interface Connector (RS232C)
used to connect the cutting plotter to a
computer through a serial interface cable.
Figure 1-5
USB Connector
used to connect the cutting plotter to a
computer through a USB cable.

Puma III User Manual
Installation 2-1
Chapter 2 Installation
2.1 Precaution
Notice 1
Carefully handle the cutter to prevent any injuries.
Make sure the power switch is off before installing the cutting plotter.
Notice 2 A proper place for installation the cutting plotter
Please select a proper location that meets the following conditions.
The machine can be approached easily from any direction.
Keep at least 60 cm space in front and behind the machine.
Make sure the cutter is placed on a flat, level and sturdy surface
The operation temperature should be between 15 and 30
℃
(60-86oF) in the
workshop.
Keep the relative humidity between 25% and 75% in the workshop.
Protecting the machine from dust and air current.
Preventing the machine from direct sunlight.
Notice 3 Connecting the Power Supply
Check the plug of the power cord to see if it matches the wall outlet. If not, please
contact your dealer.
Insert the plug (male) into a grounded power outlet.
Insert the other end (female) of power cord into the AC connector of cutting
plotter.

Puma III User Manual
Installation 2-2
2.2 Stand & Flexible Media Support System (for P3-132)
Please follow procedure below to assemble stand and media support system.
Step 1 Please examine supplied items in the accessory box of stand carton
before you install:
Stand is a optional item for Puma III-60, Item List
：
2 piece of T-shape stand
1 piece of stand beam
20 pieces of M6 screws
1 piece of M5 L-shape hexagon screw driver
1 piece of Installation Guide for Stand Set
Step 2
Remove the plotter body and the accessories from the shipped carton.
Place the stand beam upright on the T-stand and follow the number 
to assemble (See Figure 2-1 & 2-2).
There is hexagon socket head screws fasten on the T-stand on both side
taken as locating pins.
Step 3 Position the stand beam perpendicularly to part and put the screws into

T-Stand

Stand beam
Figure 2-1
Figure 2-2

Puma III User Manual
Installation 2-3
the holes and tighten them as Figure 2-2. Then the complete picture of
stand will be like Figure 2-1.
Step 4 Remove the cutting plotter from the carton. Position your stand under the
plotter, on the bottom of the plotter, there is one hole on each side in the
position corresponding to the locating pins, so the locating pins can be
located into the holes. Then insert the screws into the holes on the stand
to fix the plotter and tighten them up as shown in Figure 2-3.
Screws
Figure 2-3

Puma III User Manual
Installation 2-4
Step 5
Insert the roll holder support with the screws into the holes of the stand, and then
tighten them up as shown in Figure 2-4. You could decide roll holder support’s
position by inserting into different holes.
Step 6
Place two roll holders onto the roll holder support and ensure the white protrusion
is wedged in the groove. (Figure 2-5)
Roll holder
4 screws
Figure 2-4
Roll holder support
Roll holders
Figure 2-5

Puma III User Manual
Installation 2-5
Step 7
Lastly, the complete picture will be shown like below. (Figure 2-6)
Figure 2-6

Puma III User Manual
Installation 2-6
2.3 USB Cable Tie and Saddle
The USB cable tie and saddle assembly for the stands with Flexible Media Support
System only.
Step 1 Insert the cable tie into the upper hole of cable saddle from bottom to top.
This side up
Step 2 Place the USB cable into the cable tie and tighten the cable tie.
Step 3 Insert the cable tie end into the lower hole of cable saddle to finish the
job.

Puma III User Manual
Installation 2-7
Untied way: pull out the cable tiepull up the pinrelease the cable tie.
Pull out the cable tie
Pull up the pin
Release the cable tie

Puma III User Manual
Installation 2-8
2.4Desktop Flexible Media Support System (for P3-60 only)
Step 1
Check three spacer supports on the back of the machine.
Step 2
Insert the left and right roll holder base into the spacer supports on the left and
right side when 2 inches roll media is used.

Puma III User Manual
Installation 2-9
Step 3
Press the roll holder base and the installation is complete.
Note: Insert the left roll holder base into the middle spacer support and right roll
holder base into the right one when 1 inches roll media is used.