GE APM04 Training manual

Iu
se and Care&Installation Guide
Air Conditioner
Conten@
Adapter Plug Model and Serial Numbers
Air Direction
:
Moisture Removal
;
Air Filter
5
Problem Solver 10
Apphance Registration
2
Safe~ Instructions
2
Care and Cleaning
5 User Maintenance Instructions 5
Condenser Coils 5 Warran~
Back Cover
Consumer Services 11
Control Settings 4
Electrical Requirements
3
Ener~-Saving Tips
6
Extension Cords 3
Grille and Cabinet 5
Grounding
GE Answer Center
a
Installation Instructions
7-;
800.626.2000
Portable Models
APM04
APM05
GE Appliances

Help us
help you...
Before using your
air conditioner, read
this book carefully.
It is intended to help you operate
and maintain
your new air
conditioner properly.
Keep it handy for answers to your
questions.
If you don’t understand something
or need more help, write (include
your phone number):
Consumer Affairs
GE Appliances
Appliance Park
Louisville, KY 40225
Write down the model
and serial numbers.
You’ll find them on a label on the
frame of the air conditioner behind
the air filter.
These numbers are also on the
Consumer Product Ownership
Registration Card that came with
your air conditioner. Before sending
in this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any
correspondence or service calls
concerning your air conditioner.
If you received a damaged
air conditioner...
Immediately contact the dealer
(or builder) that sold you the air
conditioner.
Save time and money.
Before you request
service...
Check the Problem Solver. It
lists causes of the minor
operating problems that you
can correct yourself.
2
hpo*t Stiety
Wtmctions
Read all instructions before
using this appliance.
When using this appliance,
always exercise basic safety
precautions, including the
following:
● Use this appliance only for
its intended purpose as
described in this Use and Care
Book.
● This air conditioner must be
properly installed in
accordance with the
Installation Instructions
before it is used. See grounding
instructions on page 3.
c Never unplug your air
conditioner by pulling on the
power cord. Always grip plug
firmly and pull straight out from
the receptacle.
● Repair or replace
immediately all electric
service cords that have
become frayed or otherwise
damaged. Do not use a cord
that shows cracks or abrasion
damage along its length or at
either the
plug or connector end,
● Unplug your air conditioner
before making any repairs.
Note: We strongly recommend
that any servicing be performed
by a qualified individual.
● For your safety. . . do not
store or use combustible
materials, gasoline or other
flammable vapors or liquids in
the vicinity of this or any other
appliance.
SAVE THESE
INSTRUCTIONS
tiYou Need Sertice
To obtain service, see the Consumer
Services page in the back of this
book.
We’re proud of our service and
want you to be pleased. If for some
reason you are not happy with the
service you receive, here are three
steps to follow for further help.
FIRST, contact the people who
serviced your appliance. Explain
why you are not pleased. In most
cases, this will solve the problem,
NEXT, if you are still not pleased,
write
dl tie details—including your
phone number—to:
Manager, Consumer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
FINALLY, if your problem is still
not resolved, write:
Major Appliance Consumer
Action Panel
20 North
Wacker Drive
Chicago, IL 60606

Electrical Safety—WORTANT...PleaSe Read Careftily.
For personal safety, this Use of adapter plug Use of extension cords
appliance must be
(115-volt units)
not recommended
properly grounded.
Because of potential safety Because of potential safety
The Dower cord of this a~~liance is
hmards under certain conditions, we hazards under certain conditions, we
,.,.
,. --
equipped with a three-prong
strongly recommend against use of strongly recommend against the use
(grounding) plug which mates with
an adapter plug. However, if you still of an extension cord. However, if
a standard three-prong (grounding)
elect to use an adapter, where local
wall outlet (Fig. 1 ) to minimize the
codes permit, a TEMPORARY
possibility of electric shock hazard
CONNECTION may be made to a
from this appliance.
Have the wall outlet and circuit
checked by a qualified electrician
to make sure the outlet is properly
grounded.
Where a standard two-prong wall
outIet is encountered, it is your
personal responsibility and
obligation to have it replaced with
a properly grounded three-prong
wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWER CORD.
properly grounded two-prong wdl
outlet by use of a UL listed adapter
(Fig. 2) available at most Iocd
hardware stores.
PR
ER
u
FIRMCONNECTION
Fig. 2
BEFORE USE
The larger slot in the adapter must
be aligned with the larger slot in
the wall outlet to provide proper
polarity in the connection of the
power cord.
CAUTION: Attaching an adapter
ground terminal to wall outlet
cover screw does not ground
appliance unless cover screw is
metal, and not insulated, and wall
outlet is grounded through house
wiring. You should have circuit
checked by a qualified electrician
to make sure the outlet is properly
grounded.
you still elect to use an extension
cord, it is absolutely necessary that it
be a UL listed 3-wire grounding type
appliance extension cord having a
grounding type plug and outlet and
that the electrical rating of the cord
be 15 amperes (minimum) and 120
volts.
When disconnecting the power
cord from the adapter,
always
hold the adapter with one hand. If
this is not done, the adapter ground
terminal is very likely to break
with repeated use.
Should the adapter ground
terminal break, DO NOT USE the
appliance until a proper ground
has again been established.
3
I

Operating Your Air Conditioner Controls
,\
Coo[
~*Gt/ 5
‘6, Fe
2’/4
:; 0 81
*2
5\
41
/
@
74
\
0 ,/
THERMOSTAT
OFF
SELECTOR
Thermostat Control
When you turn the Thermostat
Control to the desired setting, the
thermostat will automatically control
the temperature of the indoor air.
The higher the number selected, the
cooler the room air will become.
The Save Energy Range (on some
models) is a visual reminder that
you can save energy by turning the
control to a lower number. While
the room temperature will be a
little warmer, it will still be coc}ler
and less humid than outside.
Selector Switch
(Appearance may vary slightly)
OFF turns air conditioner
off.
HI FAN provides high fan speed
operation without cooling.
Caution: If air conditioner is shut LO FAN provides low fan speed
of~ wait at least two minutes
operation without cooling.
before restarting it.
HI COOL provides cooling with
high fan speed operation.
LO COOL provides cooling with
low fan speed operation.
For normal cooling For matimum cooling
1. Set the Selector at HI COOL. temperature is not satisfactory
1. Set the Selector at HI COOL.
2. Set the Thermostat at desired
tifter a reasonable time, set the
number (usually the midpoint is a Thermostat Control at a higher 2. Set the Thermostat
at 10.
good starting position).
If room number for a cooler room or at a
lower number for
a warmer room.
For air circulation and
filtering without cooling
Set the Selector at LO FAN or
HI FAN.
For quieter operation
1. Set the Selector at LO COOL.
2. Set the Thermostat at desired
number.
Freezing up
Inside
air hot
and
humid
Outside air
temperature
dropping
on the cooling coils. The ice blocks
air flow and stops the unit from
cooling the room. This “freezing up”
is a temporary condition that most
often occurs at night when the
Thermostat is set on 9 or 10 and the
Selector is set on LO COOL.
To correct the condition, set the
Selector at HI FAN or HI COOL
with the Thermostat at
1 or 2.
If you notice that your air
conditioner is not cooling as it
should, it
may be that ice has formed

Air direction
Air direction on the indoor side is
through the front grille
and out the
top. Air
flow out the top should not
be obstructed by curtains or drapes.
Upward tilted
air discharge vanes
help cool the room evenly.
Cool air
is directed straight up.
Moisture removal
The moisture that your air
conditioner removes from the air
drains to the rear of the cabinet
where it is picked up by a
fan and
dispersed against the condenser.
Occasionally, more
likely during
start-up, a “pinging” noise may be
heard. This is normal for a short
time in less humid areas and longer
in very humid areas. This method
of moisture removal improves the
operational efficiency of your air
conditioner.
Note: Before moving your air
conditioner to another location, turn
it off and wait 5 or 10 minutes. This
will allow the condensate to drain
from the coil into the base pan.
Then, keeping a firm grip on the air
conditioner, carefully raise the
window and tilt the air conditioner
to the outside to drain the water
from the base pan.
Care and Cleating
USER MAINTENANCE
INSTRUCTIONS
Turn air conditioner off and
remove plug from wall receptacle
before cleaning.
Air Filter
The air filter behind the inlet grille
should be washed at least every
two weeks or as often as it needs
cleaning.
On the APM04 model the air filter
fits into a slot at the front of the air
discharge louvers. Remove
the
filter by grasping its top corners
and pulling up and out.
On the APM05 model the air filter
fits in a slot behind an access door
located on the front top of the air
conditioner. Remove the
t’ilter by
opening
the access door, grasping
the filter and pulling up and out.
ir Filter
Use a vacuum cleaner to clean the
filter on its dusty side or wash
gently with running water. Apply
the water from the cleaner side of
the filter to wash out the dust and
lint. Mild detergent may be used to
clean the
filter if it is very dirty.
When the air
filter is washed in
water, it must be dried before
reusing. It may be dried by gently
shaking or pressing between towels.
Replace the filter, with the filter’s
front facing you.
Note: Failure to keep the air
filter clean will result in poor
air circulation. DO NOT operate
the air conditioner without a
filter. Dirt and lint will clog the
evaporator surface, reduce air
flow, possibly cause ice to form
and reduce cooling ability.
Grilles & Cabinet
Wipe grilles with a clean cl~~th
lightly dampened with mild liquid
dishwashing detergent. Wash
cabinet with mild soap or detergent
and lukewarm water.
Condenser Coils
The coils on the weather side
of the unit should be checked
periodically and cleaned if
clogged with dirt or soot from
the atmosphere. If extremely
soiled, they may need to be
steam cleaned, a service
available through your General
Electric service outlet.
5

Ener~-sating tips
● Keep the air filter clean.
● Don’ t let the room get too hot.
Whenever possible, turn the unit
on
before the room heats up.
When heat is “stored up” in walls,
furniture, rugs and draperies, your
air conditioner takes longer to
produce the desired comfort
condition.
● Keep windows and doors
closed. Cool, dry air escapes when
they’re open.
● Keep furnace floor registers and
cold air returns closed. Cold air
can easily escape through them.
● Don’t let drapes or furniture block
the front of the unit and restrict air
flow when it is operating.
● It’s best to operate your air
conditioner at high speed during
extremely hot weather.
● Keep outdoor condenser coil
clean.
● Turn air conditioner off before
vacations or extended absences
from home.
6

~LATlON INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
lMPORTANT–Observe all governing codes and
ordinances.
lNSTALLER—Be sure to leave these instructions
with the Consumer.
CO
NSUMER–l<eep these instructions for future
reference.
ELECTRICAL REQUIREMENTS
FOR PERSONAL SAFETY:
● This appliance must be properly grounded
See page 3.
● DO not, under any circumstances, cut or
remove the third grounding prong from the
power cord.
● we recommend that you do not use an
extension cord or an adapter plug with this
appliance.
● DO not change the plug on the power cord of
this appliance.
● FOIIOW national electrical codes or local
codes and ordinances.
● This appliance must be supplied with 115V,
60Hz and connected to a properly grounded
branch circuit, protected by a 15 or 20 amp
circuit breaker or time-delay fuse.
● If the electric supply provided does not meet the
above specifications, call a licensed electrician.
● Aluminum house wiring may pose special
problems–consult a qualified electrician.
SAVE THE CARTON
For convenient storage of air conditioner during
winter months or when not in use.
TOOLS NEEDED
Phillips screwdriver
I{nife or Scissors
Flat Blade screwdriver Ruler
WINDOW REQUIREMENTS
● Standard double-hung window with actual
opening width of 22
‘~” to 36!
● Clear vertical opening of 14~z” minimum from
bottom of sash to stool.
● Install the air conditioner in a window where
there will be enough clearance around the cabinet
to allow ample circulation of air through the unit.
p’
m
1
Sash
t
22 ‘/2” to 36”
> 4
14’/2”
min.
stool
Note: All supporting parts should be
secured to firm wood, masonry or metal.
INSTALLATION OF LOCATOR
Raise the window sash and remove the handle.
Measure the window sill, side-to-side, and mark
a center line. Secure the locator on the center of
the window sill with the edge against the stool,
using two 1” long screws.
Center Line
Exterior
Wall
(continued next page)
7

INSTALLATION INSTRUCTIONS (cont,nue,,
S~RM WINDOWINTERFERENCE
To overcome storm window interference, securely
attach 2“ wide wood strips to the window stool
and sill (both places), with either nails or screws.
Strips should be as long as
wrndow opening width
and flush with back side of the window stool.
Thickness of strips should be determined by
amount of interference.
Air Aluminum
Storm
Window
Wood
Filler
Strips
L
lNS~LLATION/N WINDOW
1. Center the unit in the window opening.
Keeping a firm grip on the air conditioner,
carefully put the bottom rail between the window
stool and the locator. If the locator is too short to
hold the unit in position, insert a filler strip to raise it.
Bottom tor
Rail Strip
ed)
2. Lower the window sash tight against the
sliding panels and the rear of the grille.
Grille
J
3. Extend sliding panels out from sides of air
conditioner against window frame. Fasten each
to sash and window stool with screws.
Window
Frame J II
.
I
II
P
Sliding Panel
~~
.1
I
I
I
I
8

lNS~LLATIONOFGASKET
Cut the foam sashgap gasket to the window
width and ‘stuff” between the top of the lower
sash and glass panes of the upper sash for a seal.
\ Sash Gasket ,
REMOML FROM WINDOW
1. Turn the air conditioner off and
disconnect power cord.
2. Remove foam sash-gap gasket from
between windows.
3. Remove screws securing the sliding
panels to the lower sash and window stool.
Close sliding panels.
4. Keeping a firm grip on the air conditioner,
raise sash and carefully “rock” air conditioner
backward to drain the major portion of any
condensate water in the base of the unit. Carefully
lift the unit from the window to avoid spilling
any remaining water. Store parts for re-use with
the air conditioner.
9

~ Questions?
~ Use Ttis Problem Solver
PROBLEM
AIR CONDITIONER
DOES NOT OPERATE
AIR CONDITIONER
“DOES NOT COOL
AS IT SHOULD”
OPERATING SOUNDS
WATER DRIPPING
OUTSIDE
WATER DRIPPING
INSIDE
WATER IN BASE PAN
(ON OUTDOOR SIDE)
POSSIBLE CAUSE
● Not plugged in. Plug may have been bumped loose by vacuum cleaner
or furniture.
● If plugged in, fuse could have blown or circuit breaker may have tripped.
● Curtain, blinds or furniture blocking the front of the air conditioner will restrict air flow.
● Thermostat Control may not be set high enough. Turn knob to a higher number.
Highest setting should provide maximum cooling.
● Air filter dirty, should be cleaned at least every 2 weeks.
● Room may have been very hot when air conditioner was first turned on.
Allow time for it to cool down.
● Cold air may be escaping through open furnace
floor registers and cold air returns.
● Cooling coils have iced up. To melt ice, set the Selector Switch to HI FAN
or HI COOL with the Thermostat Control to 1 or 2.
● Thermostat click, a metallic sound, may be heard when compressor cycles
on and off. This is normal.
● Fan runs continuously when Selector Switch is in COOL or FAN position.
This is normal.
● Excess water may overflow in excessively hot and humid weather.
This is normal.
● Air conditioner must be installed level for proper water disposal.
● This is normal for a short period in areas with little humidity; normal
for a longer period in very humid areas. Moisture removed from
indoor air drains to rear of cabinet where it is picked up by a fan
and thrown
against the outdoor condenser coil.
If you need more help. ..call, toll free:
GE Answer Center
(
”
)
800.626.2000
consumer information service
10