GE AS0CD09 Series How to use

SPLIT SYSTEM AIR CONDITIONER
INDOOR/OUTDOOR UNITS
GE Consumer Service Training
TECHNICAL SERVICE GUIDE
MODEL SERIES:
Cooling only Models
AS0CD09 AS1CD09
AS0CD12 AS1CD12
AS0CD18 AS1CD18
Heat Pump Models
AS0RD09 AS1RD09
AS0RD12 AS1RD12
AS0RD18 AS1RD18
Pub # 31-9012    10/99

1
Table of Contents
Functions
Remote Controller
Specs-Heating/Cooling
Dimensions
Outdoor Unit Dimensions
Refrigeration Cycle Diagram
Operation Details
Auto Mode-(Electronic Models)
2
3
4
5
6
7
8
9
14
10
13
Dehumidification Mode
Defrost Control
Cooling/Heating Sleep Mode
Forced Operation 15
16
17
18
Test Mode
Display Function
Installation
Operation
Disassembly (Indoor Unit)
CycleTroubleshooting Guide
Voltage @ Connectors
Main PWB (Indoor Unit)
Main PWB (Indoor Unit)
35
36
39
48
49
50
Main PWB (Outdoor Unit)
Tech Sheets
ExplodedViews/Parts List
52
63

2
Functions
RESET
ON
TIME
a.m.
p.m.
OFF
TIME
a.m.
p.m.
Hr.
ON OFF
SET CANCEL
REMOTE
CONTROLLER
(Timer, see page 15) Unit can be set with timer, to shut off
after 1 hour up to limit.

3
Remote Controller
TEMPERATURE LOW HIGH
( )
( )
( )
( )
Cooling Operation Mode
Dehumidification Operation Mode
Auto Operation Mode
Heating Operation Mode
Cooling Heat Pump
(
H
: High: 98 F Low : 54 F)
00
Cooling Down to 64 F
0
Up to 86 F
0Heating Down to 60 F
0
Up to 86 F
0
:OFF, ON, OFF ON
: Cancel Sleep Mode, Timer ON or Timer OFF
:1,2,3,4,5,6,7,Off Timer (Hours)
:Fan Operates without cooling or heating.
C /F
00
Switch Temp
Reading C/F
(Manual Depress)
:Switches Temperature Reading from Centigrade to Fahrenheit
Remote Controller
Operation ON/OFF
Operation Mode Selection
Fan Speed Selection
Room, Temperature Display
Temperature Setting
Setting the Time or Timer
Timer Selection
Timer Setting
Timer Cancel
Sleep Operation
Airflow Direction Control
Fan Operation Mode
Reset

4
Product Specifications (Heating and Cooling)
* Design and Specifications subject to change without prior notice for product improvement
Cooling Only Heat Pumps

5
Dimensions
16"
TYPE "A" SCREW
INSTALLATION PLATE
Tubing hole cover
Tubing hole cover
DW
H
(1) Indoor Unit
SNOISNEMID
stinUroodnI sledoMK81sledoMK21sledoMK9
thgieH
"4.11"4.11"4.11
htdiW
"4.53"4.53"6.24
htpeD
"2.7"2.7"2.7

6
(2) Outdoor Unit
)sehcnI(NOISNEMIDSTINUROODTUO
:SLEDOM K9 K21 K81
H"9.12"9.12"8.52
W"6.13"6.13"3.43
D"3.01"3.01"6.21
Y"7.11"7.11"41
X"4.32"4.32"5.12
1L "4.31"4.31"6.41
2L "0.1"0.1"0.1
3L "0.12"0.12"0.52
4L "0.1"0.1"0.1
5L "4.32"4.32"5.12
6L "2.4"2.4"4.6
7L "0.4"0.4"4.6
8L "5.2"5.2"7.2
9L "0.3"0.3"2.3
01L "5.3"5.3"3.3
W
L6 L5 L7 L8
D L1
L2
L9L10
L3L4
H
3-way valve
3 way valve
Y
X

7
Refrigeration Cycle Diagram
Heat Pump Model Shown Below:
NOTE: Both gas and liquid interconnecting lines must be insulated because the capillaries are
mounted in the outdoor section.
LIQUID
SIDE
HEAT
EXCHANGER
(EVAPORATOR)
GAS
SIDE
CHECK VALVE
CAPILLARY TUBE
INDOOR UNIT OUTDOOR UNIT
HEAT
EXCHANGER
(CONDENSER)
COOLING
HEATING
COMPRESSOR
REVERSING
VALVE
For installation over the standard 25 Ft. distance, 0.4 ounces of refrigerant (R22) should be added for
each one foot addition.* As an example for 3 additional foot over standard add 1.3 oz. of R22, for 15
Ft., add 6 oz or R22.
SLEDOM )gnibut(eziSgnipiP ).D.O( htgneLgnipiP.DTS noitavelE
saGdiuqiLdetaR elbawollA xaM
K81LLA"8/5"8/3.tF52.tF04.tF62
K21,K9llA"2/1"4/1.tF52.tF04.tF62

8
• 5sec.;The indoor fan is delayed for 5 seconds, when operating initially, to prevent noises from occurring by
the vertical louver and airflow.
• 2min.;The reversing valve is delayed for 2 minutes to prevent the refrigerant-gas from making abnormal
noises when the heating opeation is OFF or switched to the other operation mode while compressor
is off. While compressor is running, it take 3-5 seconds to switch.
2. Airflow Direction Control
•This function is to swing the vertical louver up and down automatically and to set it at a fixed position.
•The procedure is:
1st; Press the ON/OFF Button ot operate the unit.
2nd;Press the Airflow Direction Control Button to swing the vertical louver up and down automatically
3rd; Repress the Airflow Direction Control Button to set the vertical louver at the desired position.
ALL MODELS
Operation Details
(1) Function of the main control
1.Time delay Safety Control
• 3min.;The compressor operation is delayed for 3 minutes to allow system pressures to equalize
(Compressor protection)
0
1
2
3
45
110
Cooling
Cooling
Cooling
Horizontal
Setting point:
Setting range for:
Heating
Heating
Heating (Close)
Approx. 28
67
7
8
Approx. 28
3. Cooling Operation Mode
• When selecting the Cooling ( ) Mode Operation, the unit will operate according to the setting by the remote
controller and per the operation diagram shown below.
INTAKE AIR TEMP.
SETTING TEMP. +1˚F
(Compressor ON)
SETTING TEMP. -1˚F
(Compressor OFF)
INDOOR FAN SPEED
COMPRESSOR
Selecting
fan speed Selecting fan speed
ON ONONOFF OFF
Low Low Selecting
fan speed
More than
3 minutes More than 3 minutes
Setting Temp