GE SmartWater GNSV70FBL Operating instructions

ge.com
Water Filtration System
184D1069P002 49-50197 01-06 JR
GNSV70FBL
GNSV75FWW
Owner’s Manual and
Installation Instructions
Safety Instructions . . . . . . . . . . . . .2
System Overview . . . . . . . . . . . .3–5
Installation Instructions . . . . .5–15
Battery Installation . . . . . . . . . . . .13
Faucet Installation . . . . . . . . . . . . . .9
Feed Water Supply . . . . . . . . . . . .6–8
Filter Replacement . . . . . . . . . . . .14
Flush Procedure . . . . . . . . . . . . . .15
System Installation . . . . . . . . . .10, 11
System Startup . . . . . . . . . . . . . . . .14
Tubing Connection . . . . . . . . . . . .12
Troubleshooting Tips . . . . . . . . .16
Consumer Support
Consumer Support . . . . .Back Cover
Parts List/Catalog . . . . . . . . . . . . .17
Warranty . . . . . . . . . . . . . . . . . . . .18
GNSV70FBL and GNSV75FWW are Tested and Certified by
NSF International against NSF/ANSI Standard 42 for the
reduction of Chlorine: Taste and Odor and Particulate Class I
and Standard 53 for the reduction of Lead, Cyst, Turbidity,
Asbestos, Mercury, Lindane, Atrazine, Benzene and VOC.

2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING: For your safety, the information in this manual must be followed to minimize the risk of property damage
or personal injury.
SAFETY PRECAUTIONS
■Use the Water Filtration system on a potable, safe-to-drink, home COLD water supply only. The filter canisters will not purify the water,
or make it safe to drink.
■Do not use on a hot water supply (100°F max.).
WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
PROPER INSTALLATION
This Water Filtration system must be properly installed and located in accordance with the Installation Instructions before it is used.
■Install or store where it will not be exposed to temperatures below freezing or exposed to any type of weather. Water freezing in the
system will damage it. Do not attempt to treat water over 100°F.
WARNING: Discard all unused and packaging material after installation. Small parts remaining after installation could be
a choke hazard.
■Your Water Filtration system will withstand up to 120 pounds per square inch (psi) water pressure. If your house water supply pressure
is higher than 100 psi, install a pressure reducing valve before installing the Water Filtration system.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS

Specifications Guidelines.
The Water Filtration System Uses the Following Canisters
Models GNSV70FBL and GNSV75FWW
FQSVF Filter
(160 gallon capacity)
Filter—White canisters with green band
•Reduces dirt, rust and sediment
•Reduces Chlorine: Taste and Odor
•Reduces Lead
•Reduces filterable Cysts (such as cryptosporidium and giardia)
•Reduces Turbidity
•Reduces Asbestos
•Reduces Mercury
•Reduces Lindane
•Reduces Atrazine
•Reduces Benzene
•Reduces VOC
•0.5–1 micron nominal particulate reduction
This system conforms to NSF/ANSI 42 and 53 for the specific performance claims as verified and sustained by test data. See
Performance Data Sheet for details.
Installation Overview
Locate the drinking water system on the cold water supply pipe, under the kitchen and/or bathroom sink, to filter the cold
drinking water.
3
Sink
Water Supply Valve
Adapter
Filtered Water Faucet
Inlet Outlet
Filter Canisters
Manifold
Hot Cold

Performance Data Sheet.
SmartWater Filtration System GNSV70FBL and GNSV75FWW
Using Filter FQSVF
■This System has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving
the system, as specified in NSF/ANSI 42 and 53.
■Actual performance may vary with local water conditions.
■Do not use with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Standard No. 42: Aesthetic Effects
USEPA Influent Influent Effluent % Reduction Min. Required
Parameter MCL Challenge Concentration Average Average Maximum Average Minimum Reduction
Chlorine — 2.0 mg/L ± 10% 1.94 mg/L <0.05 mg/L <0.05 mg/L 97.41% 97.22% >50%
T&O — — —— —— ——
Particulate** — ≥10000 particles 4100000 #/mL 24400 #/mL 67000 #/mL 99.35% 97.84% >85%
Standard No. 53: Health Effects
Turbidity 1 NTU*** 11 ± 1 NTU*** 11.08 NTU 0.21 NTU 0.38 NTU 98.04% 96.20% 0.5 NTU
Cysts 99.95% red. Min. 50000L 141750 #/L <1 #/L 2 #/L >99.99% >99.99% >99.95%
Asbestos 99% red. 107and 108fibers/L; 168 MF/L 0.99885891 MF/L <1 MF/L 99.89% 99.82% >99%
fibers >10 µm long
Lead, 0.015 mg/L 0.15 mg/L ± 10% 0.147 mg/L <0.001 mg/L <0.001 mg/L 99.32% 99.29% 0.010 mg/L
pH 6.5
Lead, 0.015 mg/L 0.15 mg/L ± 10% 0.143 mg/L <0.001 mg/L <0.001 mg/L 99.30% 99.29% 0.010 mg/L
pH 8.5
Mercury, 0.002 mg/L 0.006 mg/L ± 10% 0.006033333 mg/L <0.0002 mg/L <0.0002 mg/L 96.68% 96.49% 0.002 mg/L
pH 6.5
Mercury, 0.002 mg/L 0.006 mg/L ± 10% 0.0058 mg/L 0.000333 mg/L 0.0005 mg/L 94.34% 92.06% 0.002 mg/L
pH 8.5
Lindane 0.0002 mg/L 0.002 mg/L ± 10% 0.002016667 mg/L <0.00002 mg/L <0.00002 mg/L 99.00% 98.95% 0.0002 mg/L
Benzene 0.001 mg/L 0.015 mg/L ± 10% 0.01417 mg/L 0.000500 mg/L 0.000500 mg/L 96.47% 96.43% 0.005 mg/L
Atrazine 0.003 mg/L 0.009 mg/L ± 10% 0.00830 mg/L 0.002000 mg/L 0.002000 mg/L 74.82% 61.54% 0.003 mg/L
VOC Reduction
Chloroform 0.080 mg/L 0.30 ± 10% 0.31429 mg/L 0.00186429 mg/L 0.0055 mg/L 99.40% 98.28% 95%
*Tested using a flow rate of 0.60 gpm (2.27 l/min); pressure of 60 psig; pH of 7.5 ± 0.5; temp. of 68° ± 5°F (20° ± 3°C)
**Measurement in particles/mL. Particles used were 0.5–1 microns.
***NTU—Nephelometric Turbidity Units
Operating Specifications
Capacity: certified for up to 160 gallons (605 l); up to six months
Pressure requirement: 35–120 psi (2.8–8.2 bar)
Temperature: 33–100°F (0.6–38°C)
Flow rate: 0.60 gpm (2.27 l/min)
4
Replacement Filter Canisters/Estimated Replacement Costs
FQSVF—Replacement filter canister $35–40
For replacement parts, call toll-free 800.626.2002 (U.S.), 800.663.6060 (Canada–English), 800.361.3869 (Canada–French)
IOWA RESIDENTS ONLY:
Store or Seller’s Name
Address
City State Zip Telephone
Seller’s signature
Customer’s signature Date
State of California
Department of Health Services
Water Treatment Device
Certificate Number
Date Issued: February 9, 2004
160104 -
Trademark/Model Designation Replacement Element(s)
GXSV65 F FQSVF
GQSV65 F FQSVF
GNSV70 FBL FQSVF
GNSV75 FWW FQSVF
Cysts
Turbidity
General Electric Company
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section
116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity Inorganic/Radiological Contaminants
Atrazine
Lindane
Benzene
VOCs
Organic Contaminants
Alachlor
Atrazine
Benzene
Carbofuran
Carbon Tetrachloride
Chlorobenzene
Chloropicrin
2,4-D
DBCP
o-Dichlorobenzene
p-Dichlorobenzene
1,2-Dichloroethane
1,1-Dichloroethylene
cis-1,2-Dichloroethylene
trans-1,2-Dichloroethylene
1,2-Dichloropropane
cis-1,3-Dichloropropylene
Dinoseb
Simazine
Styrene
1,1,2,2-Tetrachloroethane
Tetrachloroethylene
Toluene
2,4,5-TP (Silvex)
Tribromoacetic Acid
1,2,4-Trichlorobenzene
1,1,1-Trichloroethane
1,1,2-Trichloroethane
Trichloroethylene
Trihalomethanes (THMs)
Bromodichloromethane
Bromoform
Chloroform
Chlorodibromomethane
Xylenes
Endrin
Ethylbenzene
EDB
Haloacetonitriles (HAN)
Bromochloroacetonitrile
Dibromoacetonitrile
Dichloroacetonitrile
Trichloroacetonitrile
Haloketones (HK)
1,1-Dichloro-2-Propanone
1,1,1-Trichloro-2-Propanone
Heptachlor
Heptachlor Epoxide
Hexachlorobutadiene
Hexachlorocyclopentadiene
Lindane
Methoxychlor
Pentachlorophenol
160 gal
Rated Service Capacity: 0.6 gpm Rated Service Flow:
Do not use where water is microbiologically unsafe or with water of unknown quality, except that
systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Manufacturer:
Asbestos
Lead
Mercury

Installation Instructions.
Important Installation Recommendations
WARNING: Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.
■Check with your local public works department for plumbing codes. You must follow their guides as you install the Water Filtration system.
Tools and Materials Required for Installation
•Phillips screwdriver
•Two (2) adjustable wrenches
•Electric drill and drill bit to drill 3/4″hole (type as required) if mounting hole is needed for faucet
•1/16″drill bit (optional for pilot holes)
•Tape measure
•If your main water line is a rigid pipe, you will require a compression fitting and possibly other plumbing hardware to complete
the installation.
CAUTION: To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures. Special drill bits may
be needed for porcelain or stainless steel.
Contents Included with the Product
•Water filter system assembly, including mounting screw
•Feed water adapter and supply valve
•Faucet assembly with electronic base monitor and tubing
1Influent challenge levels are average influent concentrations determined in surrogate qualification testing.
2µg/L means Micrograms Per Liter.
3Maximum product water level was not observed but was set at the detection limit of the analysis.
4Maximum product level is set at a value determined in surrogate qualification testing.
5Chemical reduction percent and maximum product water level calculated at chloroform 95% breakthrough point as determined in surrogate qualification testing.
6The surrogate test results for heptachlor Epoxide demonstrated a 98% reduction. These data were used to calculate an upper occurrence concentration, which would produce a maximum product water level at the MCL.
Organic Chemicals Reduced by Chloroform Surrogate Testing
Avg.1Max.
Contaminant Influent (µg/L)2Effluent (µg/L)2
Alachlor 50 1.03
Atrazine 100 3.03
Benzene 81 1.03
Carbofuran 190 1.03
Carbon Tetrachloride 78 1.84
Chlorobenzene 77 1.03
Chloropicrin 15 0.24
2,4-D 110 1.74
Dibromochloropropane (DBCP) 52 0.023
o-Dichlorobenzene 80 1.03
p-Dichlorobenzene 40 1.03
1,2-Dichloroethane 88 4.85
1,1-Dichloroethylene 83 1.03
cis-1,2-Dichloroethylene 170 0.53
trans-1,2-Dichloroethylene 86 1.03
1,2-Dichloropropane 80 1.03
cis-1,3-Dichloropropylene 79 1.03
Dinoseb 170 0.24
Endrin 53 0.594
Ethylbenzene 88 1.03
Ethylene Dibromide (EDB) 44 0.023
Haloacetonitriles (HAN):
Bromochloroacetonitrile 22 0.54
Dibromoacetonitrile 24 0.64
Dichloroacetonitrile 9.6 0.24
Trichloroacetonitrile 15 0.34
Testing was performed under standard laboratory conditions; actual performance may vary.
NOTE: Substances reduced are not necessarily in your water. Filter must be maintained according to manufacturer’s instructions, including replacement of filter cartridges.
WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be
used on disinfected waters that contain filterable cysts.
Performance Data Sheet.
5

Installation Instructions.
Feed Water Adapter and Supply Valve
A. PREFERRED INSTALLATION
(Utilizing existing kitchen sink water supply valve [A] and removable faucet tubing [B])
For 1/2-inch and 3/8-inch installations
1. Refer to Fig. 1 to complete assembly depending on supply valve size (A).
2. Turn off the COLD water supply valve (A).
3. Unscrew the existing faucet tubing line (B) from the supply valve (A), COLD side only. NOTE: For rigid pipe, see C. Optional Installation
on page 7.
6
(B) Faucet tubing
line (not included)
(D) Coupling
(C) Adapter
(A) Water supply
valve (not included)
(F) Inlet valve
(G) Gasket
(H) Ferrule
(I) Nut
(F) Inlet valve
Fig. 2
Fig. 1
For 3/8-inch Valve For 1/2-inch Valve
(C) Adapter
(G) Gasket
(F) Inlet valve
(D) Coupling
(B) Faucet tubing
line (not included)
(A) Water supply
valve (not included)

7
Installation Instructions.
Feed Water Adapter and Supply Valve
4. Assemble adapter (C) and coupling (D) as shown in Fig. 1, per your configuration. Be sure the gaskets (G) are in place before final
assembly. Start installation by hand, then finish tightening with adjustable wrench. Be careful not to overtighten or cross thread as
damage to threads may occur.
Note Adapter (C) orientation:
1/2-inch Installation—Rounded end of adapter (C) connects to coupling (D), then to existing faucet tubing (B).
3/8-inch Installation—Rounded end of adapter (C) connects to supply valve (A).
5. Hand tighten assembled adapter (C) onto supply valve (A) for the proper size installation. Be sure the gaskets (G), as shown
in Fig. 1, are in place before final assembly. Finish tightening with adjustable wrench. Be careful not to overtighten or cross
thread as damage to threads may occur.
NOTE: If inlet valve needs to be removed to complete this step, refer to D. Removal and Reinstallation of Inlet Valve on page 8.
6. Reconnect faucet tubing line (B) to top of adapter (C).
7. Remove nut and ferrule from end of inlet valve. Using the 4 feet of tubing provided, place the nut (I) and ferrule (H) onto
the tubing and install onto inlet valve (F) as shown in Fig. 2. Tighten with adjustable wrench.
NOTE: Inspect the ends of the tubing to be sure there are no imperfections and end of tubing is cut square. It may be necessary to cut the tubing again.
B. OPTIONAL HOME INSTALLATION—SADDLE VALVE
(Where codes permit): Saddle valve must be able to connect with 1/4-inch tubing supplied with system.
Not supplied with product; check your local hardware or home service store for product.
For 1/2″OD or larger metal tubing only.
NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of the saddle valve.
For installation, use plumbing code 248-CMR of the Commonwealth of Massachusetts.
1. Turn off the cold water supply and install saddle valve as required by product selection. (Be sure to follow manufacturers’
installation instructions.)
DANGER: If hole is required to be drilled in pipe, to protect yourself from serious injury or fatal shock, use a battery
powered hand drill only to make the hole. DO NOT USE AN ELECTRIC DRILL.
Open only after complete system has been installed.
C. OPTIONAL INSTALLATION
(For installation with rigid pipe between supply valve and sink faucet)
Option 1
1. Remove pipe from supply valve and sink faucet.
2. Obtain flexible pipe sized to your plumbing.
3. Install flexible pipe to sink.
4. Go back to A. Preferred Installation section step 4.
Option 2
1. Obtain compression fittings to fit rigid pipe.
2.
Obtain any other fittings required to connect compression fittings to adapter.
NOTE: Adapter has 1/2-inch and 3/8-inch internal and external threads.
3. Remove pipe from supply valve.
4. Cut pipe to fit length of assembled fittings and adapter.
5. Install compression fitting to pipe.
6. Go back to A. Preferred Installation section step 4.
NOTE: Above described materials are not included with the product.

8
Installation Instructions.
Feed Water Adapter and Supply Valve
D. REMOVAL AND RE-INSTALLATION OF INLET VALVE (This is only required if inlet valve needs to be removed to complete Step 5 on page 7.)
1. Remove inlet valve (F) from adapter (C) using adjustable wrench on valve body. See Fig. 3a for details. DO NOT USE WRENCH ON HEX
NUT END OF VALVE AS LEAK MAY OCCUR.
2. Remove all sealing tape from inlet valve (F) and adapter (C) threads.
3. Hand tighten assembled adapter (C) onto supply valve (A) for the proper size installation. Be sure the gaskets (G), as shown in Fig. 1,
are in place before final assembly. Finish tightening with adjustable wrench. Be careful not to overtighten or cross thread as damage
to threads may occur.
4. Using white thread sealing tape provided, apply approximately 9 wraps of tape around the large threads on inlet valve (F) in a
clockwise direction, as shown in Fig. 3b.
5Hand tighten inlet valve (F) into the adapter (C), then finish tightening with adjustable wrench (see Fig. 3a). DO NOT USE WRENCH
ON HEX NUT END OF VALVE AS LEAK MAY OCCUR.
Faucet Spout Installations (see Fig. 4, page 9)
1. Remove spout (A) and faucet body (B) from faucet packaging.
2. Move the threaded dome-shaped collar (C) on the spout up and away from the o-rings on the spout.
3. Gently insert the spout into the top of the faucet body.
NOTE: Turning the spout left to right during installation will help the o-rings to slide in easily.
4. Once the spout (A) has been installed and fully seated, slide the threaded collar (C) down to the faucet body (B).
5. Tighten the collar by hand to the faucet body by turning in a clockwise direction.
Fig. 3a
Fig. 3b

9
Installation Instructions.
Faucet Installation
Be sure there is room underneath and above the sink to make the needed connections. Before starting, make sure there is sufficient
room for the battery powered faucet base. Select one of the following places to install the faucet:
1. In an existing sink spray attachment or soap dispenser hole.
2. In a hole to be drilled in the sink top.
3. In a hole to be drilled in the countertop, next to the sink.
NOTE: Be sure the faucet base will fit flat against the surface at the selected location so the bottom gasket between the base and surface area will seal.
Installation Steps (refer to Fig. 4 for clarification)
1. If drilling is needed, make a 3/4″diameter hole.
Be sure to use the proper procedure for drilling porcelain or stainless steel. Special drill bits may be needed. Consult a qualified plumber
for the proper procedure.
2. Remove the faucet with pre-installed tubing, thin o-ring (D), faucet base (E), bottom base gasket (F), lock washer (G), hex nut (H)
and mounting bracket (I) from the packaging.
3. Feed tubing connected to the faucet through the thin o-ring (D), faucet base (E), bottom base gasket (F), lock washer (G) and
hex nut (H).
4. Thread the hex nut (H) up the stem of the faucet until the height between the bottom of the base gasket (F) and top of the lock
washer (G) is slightly larger than the thickness of the mounting surface (J).
5. Lower the faucet assembly into place in the mounting hole and orient to final position. Place the mounting bracket (I)
above the lock washer (G) around the faucet stem (Fig. 5). While holding the mounting bracket in place, securely tighten
the hex nut.
NOTE: Two people may be required to complete this step.
(D) O-ring
(F) Gasket
(E) Faucet base
(A) Spout
(G) Lock washer
(H) Hex nut
(I) Mounting
bracket
Fig. 4
Fig. 5
(J) Mounting surface
(C) Collar
(B) Faucet body

10
Installation Instructions.
Mounting System Installation
Pick a location under the sink to mount the system. Location should be easily accessible, with clearance between the bottom of the filter
canisters and the floor or bottom of the cabinet; any less will result in difficulty of removing filter canisters (see Fig. 7). Allow enough
space on either side of the system for the tubing connections.
SCREW INSTALLATION
1. Remove this template from the manual for easier installation.
2. The top of the template openings should be placed a minimum of 17 inches above the bottom of the cabinet or floor where the
system is to be mounted (Fig. 6 and 7).
NOTE: Any distance lower may result in filter canisters interfering with the floor when removed.
3. Tape template to wall, then mark the wall where the screws are to be installed.
Install screws into the wall, leaving 3/16 inch clearance between the head of the screw and wall (drill pilot holes if needed) (Fig. 8).
17 inches
5 inches
Bottom of Cabinet or Floor
Template for screw hole pattern on back of filtration system
Fig. 6
17 inches
5 inches
Screws
Screw
3/16 inch
Fig. 8
Fig. 7
Wall