GEIGER PRO.TECline GB45 M01 Series User manual

1
www.geiger.de EN
EN
DE
EN
FR
ES
IT
Original-Montage- und
Betriebsanleitung
Original assembly and
operating instructions
Notice originale de montage
et d’utilisation
Instrucciones originales de
instalación y funcionamiento
Istruzioni originali di
installazione e funzionamento
Tubular motor:
GEIGER PRO.TECline
Motor control:
PRO.TECline Spindle (GB45...-M01)
for rolling shutters and screens

2Gerhard Geiger GmbH & Co. KG | 100W2544 0521V000en
EN
EN
Index
1. General information..................................................................2
2. Guarantee ..................................................................................3
3. Intended use..............................................................................3
4. Safety instructions....................................................................3
5. Safety instructions for assembly ............................................4
6. Installation instructions ...........................................................5
7. Information for the specialist electrician................................6
8. Setting of the end positions.....................................................6
9. What to do if…...........................................................................8
10. Technical data ...........................................................................9
11. Maintenance ..............................................................................9
12. Notes on waste disposal ..........................................................9
13. Declaration of conformity ......................................................10
1. General information
Dear customer,
By purchasing a GEIGER motor you have decided on a quality product from GEIGER.
Thank you very much for your decision and the condence placed in us.
Before you put this drive into operation please observe the following safety instructions. It
serves for the prevention of danger and for the avoidance of personal injury and damage to
property.
The installation and operating instructions contain important information for the installer, the
specialist electrician and the user. Please pass on these instructions if you transfer the product.
These instructions should be kept by the user.

3
www.geiger.de EN
EN
2. Guarantee
In the case of incorrect installation contrary to the installation and operating instructions and/
or constructional modication, the legal and contractual guarantee for property damage and
product liability lapses.
3. Intended use
The tubular motors of the model range PRO.TECline (GB45...-M01) with the Spindle system
are designed exclusively for the operation of rolling shutters and screens.
The motors may not be used for the operation of roller grilles, garage doors, furniture and lifting
tools.
GB 45 .. . - M01
Motor control
Motor head
Torque in Nm
Motor diameter
GEIGER PRO.TECline
4. Safety instructions
I ATTENTION: Important safety instructions. For personal safety,
it is important to follow these instructions. Please keep these
instructions for future reference.
fDo not allow children to play with stationary controls. Keep remote controls away
from children.
fThe installation is to be checked regularly for defective balance, signs of wear or
damaged cables and springs, if relevant.
fDo observe the moving sun protection system and keep persons away until it has
closed completely.
fWhen operating the manual release with the sun protection system open, please be
cautious as it can fall down quickly if springs or tapes wear off or are broken.
fDo not operate the device if operations such as, for example, window cleaning are to
be carried out in the vicinity.
fDisconnect the automatic controlled device from the mains power supply if opera-
tions such as, for example, window cleaning are being carried out in the vicinity.
fDuring operation observe the danger zone.
fDo not use the installation if people or objects are in the danger zone.
fUrgently shut down damaged installations until repair.
fUnconditionally shut down the unit during maintenance and cleaning operations.
fPinching and shearing points are to be avoided and must be secured.
fThis appliance can be used by children aged 8 and above and persons whose
physical, sensorial or mental capacities are impaired, or who have no experience or
know-how if they have been supervised or been given instructions on the use of the
appliance and if they understand the possible resulting dangers. Children are not
permitted to play with the device. Cleaning and maintenance should not be carried
out by children.
fThe rated sound pressure level is less than 70 dB(A).
fDisconnect the device from the mains power supply for maintenance and replace-
ment of parts.
If the motor is disconnected via a plug connection the operator must be able to
control - from any place to which it has access – that the plug is removed.
If this is not possible - due to design or installation - the disconnection from the
power supply must be ensured via locking in the disconnected position (e.g. isolator).
fThe motor tube can get very hot during prolonged use.
When working on the unit, do not touch the tube before it has cooled down.

4Gerhard Geiger GmbH & Co. KG | 100W2544 0521V000en
EN
EN
5. Safety instructions for assembly
I ATTENTION: Important safety instructions. Follow all installation
instructions, as incorrect installation can lead to serious injuries.
fWhen mounting the motor without any mechanical protection of the driven parts and
of the tube which may become hot, the motor must be installed at a height of at least
2.5 m above the ground or of another level which provides access to the drive.
fBefore the motor is installed, all cables which are not needed are to be removed and
all equipment which is not needed for power-operated actuation is to be put out of
operation.
fThe actuating element of a manual release must be mounted at a height of less than
1.8 m.
fIf the motor is controlled by a switch or pushbutton, the switch or pushbutton must
be mounted within eyeshot of the motor. The switch or pushbutton must not be
located in the vicinity of moving parts. The height of installation must be at least
1.5mabovetheoor.
fPermanently installed control devices must be attached visibly.
fIn case of devices extending horizontally, a horizontal distance of at least 0.4 m must
berespectedbetweenthefullyextendedpartandanyotherxedelement.
fThe rated speed and the rated torque of the motor must be compatible with the
device.
fThe mounting accessories that are used must be designed in accordance with the
selected rated torque.
fGood technical knowledge and good mechanical skills are necessary for the motor
installation. Incorrect installation can lead to serious injury.
Electricalworkmustbecarriedoutbyaqualiedelectricianinaccordancewiththe
regulations in force locally.
fOnly use connecting cables that are suitable with the environmental conditions and
which meet the construction requirements. (see accessories catalogue)
fIf the device is not equipped with a connecting cable and a plug, or other means for
disconnecting from the mains with a contact opening on each pole according to the
conditions of the overvoltage category III for full disconnection, a disconnecting
device of this type must be incorporated into the permanently installed electrical
installation according to the wiring rules.
fDo not mount the connecting cables near hot surfaces.
fA plug for the disconnection of the motor from the power supply must be accessible
after installation.
fDamaged connecting cables must be replaced by GEIGER connecting cables of the
same type.
fThe device must be mounted as described in the installation instructions. Fixations
shall not be made with adhesives since they are regarded as unreliable.

5
www.geiger.de EN
EN
6. Installation instructions
I Prior to installation please check to ensure there is no visible damage
to the motor like cracks or open cables.
I Beforexingpleasecheckthestrengthofthemasonryandofthe
surface.
I Caution: If the tube is screwed/riveted to the drive, the measure must
be taken from the tube end to the center of the drive and marked on
the tube.
When drilling the winding shaft never drill into the
area of the tubular motor!
When inserting into the shaft, the tubular motor must not
be struck and must not be allowed to fall into the shaft.
Installation into the rolling shutter:
Fix motor support to available stud bolts or in the side
frame.
Insert motor into the shaft with a suitable adapter and drive
up to the stop of the shaft adapter.
Insert roller capsule on the opposite side.
Put shaft with motor on motor support or on pivoting
engine bearer. On the opposite side pull out roller capsule
until bolt ts into ball bearing.
Screw together roller capsule with shaft.
Screw together shaft with tubular carrier.
Fix rolling shutter casing to shaft.
Installation into screens:
Insert motor with a suitable adapter and drive into the shaft
up to the stop of the shaft adapter.
Fix the motor support on the awning. Fix the motor
together with the shaft on the motor support. The bearer
locks into place.
Depending on the selected motor head, different
xationsystemscanbeused:
– Place the motor with square insert in the star-shaped
bearer and lock with pin
– Place the motor into the existing engine bearer and
lock
– Place the motor in a compatible engine bearer with clip
system and lock with spring or rotating lever
I The GEIGER PRO.TECline motor is
suitable for shaft diameters from 50 mm!

6Gerhard Geiger GmbH & Co. KG | 100W2544 0521V000en
EN
EN
7. Information for the specialist electrician
H Caution: Important installation instructions.
Please follow all instructions since
incorrect installation can lead to
the destruction of the motor and the
switching unit.
Because of back-voltage of the capacitor, the parallel
connection of the PRO.TECline Spindle is not permissible.
Please do not use any installation switch which allows
simultaneous up and down controls.
The operations with the service clamps may be accom-
plished only by an electrical specialist.
When changing the running direction the switchover must
be effected through an off-position.
When changing the running direction the switchover time
must be at least 0.5 s.
A voltage rise occurs at the LC unit (coil-capacitor unit) of
the auxiliary line. The excessive mains voltage is applied
respectively to the non-controlled input.
PVC cables are not suitable for equipment used outdoors
or exposed to prolonged high levels of UV radiation. These
cables should not be used if they are likely to touch metal
parts that can heat up to temperatures exceeding 70°C.
8. Setting of the end positions
I CAUTION: In the factory setting, the motor can make 2 rotations in
both directions.
Installationconguration
CDAB
Top-mounted box/
right-hand installation
Front-mounted box/
left-hand installation
Top-mounted box/
left-hand installation
Front-mounted box/
right-hand installation
The setting of the end positions for installation situations A and B is described below.
In situations C and D, the assignment of the setting screws changes.
To turn the setting screws, use a 4mm hexagon key or the included adjustment aid.
PE N
L1
N
PE
Mechanical
limit stop
blue brown black green/yellow
Mains 230V / 50Hz

7
www.geiger.de EN
EN
Changing the setting range
Irrespective of the assignment of the setting screws:
• Rotation in minus direction reduces the setting range
• Rotation in plus direction increases the setting range
Setting the upper end position
Press the UP key on the control switch until the hanging
stops automatically.
Depending on the installation situation, turn the
corresponding setting screw with UP key pressed down in
PLUS direction until the selected upper end position is
reached.
If the upper end position is overrun (the motor
switches off too late):
• Press the DOWN key until the hanging is below the selected end position.
• Turn the setting screw a few turns in MINUS direction and repeat the procedure described
above again.
Setting the lower end position
Press the DOWN key on the control switch until the
hanging stops automatically.
Depending on the installation situation, turn the
corresponding setting screw with DOWN key pressed
down in PLUS direction until the selected lower end
position is reached.
If the lower end position is overrun (the motor
switches off too late):
• Press the UP key until the hanging is above the selected end position.
• Turn the setting screw a few turns in MINUS direction and repeat the procedure described
above again.

8Gerhard Geiger GmbH & Co. KG | 100W2544 0521V000en
EN
EN
9. What to do if…
Problem Solution
Motor does not run. • Motor not plugged in.
Please check the plug connection.
• Check connecting cable for possible
damage.
• Check the mains voltage and allow the
cause of the voltage breakdown to be
tested by a specialist
electrician.
Instead of in the upwards direction, motor
runs downwards.
• The control leads are interchanged.
Exchange black/brown control leads.
Motor only runs in one
direction.
• Motor in the end position.
Run motor in the opposite direction.
• Check control leads.
After running several times,
the motor breaks down and
no longer responds.
• The motor became too hot and has
switched off.
Try it again after a cooling time of about
15 min.
The adjusted end position
is not correct.
• Adjusting knob not pressed properly.
Repeat adjustment process, press adjus-
ting knob deeply.
• Actuator does not rotate simultaneously.
Push shaft onto tube actuator, repeat
adjustment process.

9
www.geiger.de EN
EN
10. Technical data
Technical data of tubular motor PRO.TECline Spindle (GB45..)
GB4510 GB4520
Voltage 230 V~/50 Hz
Current 0,47 A 0,63 A
Cos Phi (cosj)>0,95
Inrush current (factor) x 1,2
Power 105 W 140 W
Torque 10 Nm 20 Nm
Speed 15 rpm
Protection class IP 44
Total length 438 mm 468 mm
Operating mode S2 4 min
Sound pressure level1) 39 dB(A)
Diameter 45 mm
Limit switch range 22 rotations
Weight ca. 1,90 kg ca. 2,00 kg
Storage temperature/
Humidity
T = -15°C .. +70°C / dry and non-condensing place
1) The average sound pressure level data are intended for guidance only. The values were determined by
GEIGER at a distance of 1 m, with a hanging motor at idle speed and averaged over 10 seconds. There is
no reference to any specific test standard.
Subject to technical modifications. Please find information to the ambient
temperature range of our GEIGER motors under www.geiger.de
11. Maintenance
The drive is maintenance-free.
12. Notes on waste disposal
Recycling of packaging materials
In the interest of environmental protection, please contact your local government’s recycling or
solid waste management department to learn more about the services it provides.
Waste disposal of electric and electronic equipment
Electrical and electronic equipment must be collected and disposed of separately in accordance
with EU regulations.

10 Gerhard Geiger GmbH & Co. KG | 100W2544 0521V000en
EN
EN
13. Declaration of conformity
Current declarations of conformity are available under www.geiger.de
Schleifmühle 6 |D-74321 Bietigheim-Bissingen
Phone [phone] |Fax [phone] |[email protected] |www.geiger.de
Sitz Bietigheim-Bissingen |Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146
Komplementär: Geiger Verwaltungs-GmbH |Sitz Bietigheim-Bissingen |Amtsgericht Stuttgart HRB 300481
Geschäftsführer: Roland Kraus |WEEE-Reg.-Nr. DE47902323
Gerhard Geiger GmbH & Co. KG
300H0204
EU Declaration of Conformity
Bietigheim-Bissingen, 06.04.2021 Roland Kraus (General Manager)
Product designation:
Venetian blinds motor, motor for rolling shutters, motor for awnings
Type designation:
GJ56.., GR45.., GU45.., GSI56.., GS56.., GS45.., GB45.., GB35..
Applied directives:
2006/42/EG
2014/53/EU
2011/65/EU + (EU)2015/863 + (EU)2017/2102
Applied standards:
EN 60335-1:2012
EN 60335-1:2012/AC:2014
EN 60335-1:2012/A11:2014
EN 60335-1:2012/A13:2017
EN 60335-1:2012/A1:2019
EN 60335-1:2012/A14:2019
EN 60335-1:2012/A2:2019
EN 60335-2-97:2006+A11:2008+A2:2010+A12:2015
EN 62233:2008
EN 62233 Ber.1:2008
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2019
EN 61000-3-3:2013
ETSI EN 301 489-1 V2.2.0(2017-03)
ETSI EN 301 489-3 V2.1.1(2019-03)
ETSI EN 300 220-2 V3.1.1(2017-02)
DIN EN IEC 63000:2019-05
Authorized representative for technical data:
Gerhard Geiger GmbH & Co. KG
Address:
Schleifmühle 6, D-74321 Bietigheim-Bissingen
en
Gerhard Geiger GmbH & Co. KG
Antriebstechnik
Schleifmühle 6
D-74321 Bietigheim-Bissingen
0421100W1518

11
www.geiger.de EN
EN

12 Gerhard Geiger GmbH & Co. KG | 100W2544 0521V000en
EN
EN
For technical questions, please call our service team at: [phone].
They will be happy to assist you.
Gerhard Geiger GmbH & Co. KG
Schleifmühle 6 | D-74321 Bietigheim-Bissingen
T [phone] | F [phone]
[e-mail] | www.geiger.de