GEIGER SOLIDline GJ56 Series Operating manual

Setting instructions
SOLIDline motors / Connections
Running direction
The allocation of the running directions
UP/ DOWN to the connecting cables depends
on the mounting direction of the motor. That is
why it might be better to refer to right and left
directions instead of UP/DOWN directions.
Circuit diagram
motor
Links
Left
A
gauche
Rechts
Right
A droite
Sensor
Capteur
2x
M
NPE
Wiring
123
blau
blue
bleu
braun
brown
brun
grün-gelb
green-yellow
vert-jaune
schwarz
black
noir
Assignment
Color of cable Function
Green-yellow Protective conductor
Blue Neutral conductor
Brown Running direction: right
Black Running direction: left
Motor
Moteur
Blickrichtung
Vi
ewing direction
Perspective
Laufrichtung Rechts
Running direction right
Marche à droite
Elektronik
Electronic
Electronique
Kabel 4-adri
g
4-wire cabl
e
Câble 4 fils
SOLIDline motors with mechanical end stop (Touch)
A parallel connection is
only possible with a cut-off
relay. Otherwise the motor
would be irreparably
damaged.
Never actuate simul-
taneously the UP and
DOWN keys because this
would damage the motor
irreparably.
Please consider a switch-
over time of 500ms for
BUS systems.
SOLIDline radio-controlled motors (e.g. VariousWireless)
L1
schwarz
black
noir
N
blau
blue
bleu
PE
grün-gelb
green-yello
w
vert-jaune M
~
The brown wire of the
connecting cable is not
needed in case of radio-
controlled motors.
Netz 230V/50Hz
Power supply 230V/50Hz
Courant 230V/50Hz
Several motors can be
connected in parallel. In
this case the maximum
load of the switching unit
must not be exceeded.
SOLIDline motors with electronic end stop (e.g. Easy)
Netz 230V/50Hz
Power supply 230V/50Hz
Courant 230V/50Hz
Do not use any switch that
allows a simultaneous UP
and DOWN command.
Please consider a switch-
over time of 500ms for
BUS systems.
Do not use any switch that
allows a simultaneous UP
and DOWN command.
Please consider a switch-
over time of 500ms for
BUS systems.

100W1545 en 0914
Running direction
When viewed from inside the room
the power supply connection of
the GJ56 is located on the left
side. This guarantees the
direction of rotation and the
correct function of the limit stop
switch.
Circuit diagram
motor
AUF
UP
HAUT
AB
DOWN
BAS
Sensor
Capteur
2x
M
NPE
Wiring
123
blau
blue
bleu
braun
brown
brun
grün-gelb
green-yellow
vert-jaune
schwarz
black
noir
Assignment
Color of cable Function
Green-yellow Protective conductor
Blue Neutral conductor
Brown Running direction: UP
Black Running direction: DOWN
Laufrichtung AUF
Running direction UP
Marche HAUT
Setting instructions
GJ56.. motors / Connections
GJ56.. with mechanical end stop
A parallel connection is
only possible with a cut-off
relay. Otherwise the motor
would be irreparably
damaged.
Never actuate simultane-
ously the UP and DOWN
keys because this would
irreparably damage the
motor.
Please consider a switch-
over time of 500ms for
BUS systems.
GJ56.. with electronic end stop
Netz 230V/50Hz
Power supply 230V/50Hz
Courant 230V/50Hz
Several motors can be
connected in parallel. In
this case the maximum
load of the switching unit
must not be exceeded.
Do not use any switch that
allows a simultaneous UP
and DOWN command.
Please consider a switch-
over time of 500ms for
BUS systems.
Gerhard Geiger GmbH & Co. KG • Schleifmühle 6 • D-74321 Bietigheim-Bissingen
Phone: [phone] • Fax: [phone] • www.geiger.de • [e-mail]