GEM DG-30 User manual

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG30 Ver. A Publish:2004.08.26 Page: 1/ 4
DG-30 Digital Keypad / Proximity Entry system
Operation User's Manual
1. Product Characteristic:
Allows up to 150 Proximity cards / tokens or PIN codes
Tamper Switch Included
Door Reed Switch Input for Anti-Trailing
Fully Programmable via keypad and master code
Extendable from keypad only to proximity controller
Supports 26 or 34-bit Wiegand auxiliary reader
Logical memory to prevent duplication
Non-Volatile Memory
Invalid PIN Lock-out
2. Specifications:
Operating Voltage: 12 Vdc
Current Draw: 60mA Max @12VDC
Input: request-to-exit, time out reed switch contact, auxiliary reader
Relays Electric Current: 2A MAX @30Vdc ；0.4A @ 120Vac
Memory Volume: 150 PIN codes or 100 Proximity cards/tokens and 50 PIN codes
Format: 26 or 34-bit Wiegand hexadecimal.
Relay 1 is controlled by 001~100 user slots（Cards or PIN codes）
Relay 2 is controlled by 101~150 user slots（PIN codes）
PIN codes: 5 digit codes only
Case Material: ABS （UL94V0）
Operating Temperature: -20~+70℃
Ambient Humidity: 5~95% relative humidity non-condensing
Visual Signals:
Red: Power on
Green: Relay activated
Tri-color LED:
Yellow: Program Mode
Red: The slot is registered、Lock-out
Green: This slot may register the card or PIN codes.
Factory Master Code: 12345
Invalid PIN Lock-out: The system will shut down for 60 seconds while 32 codes of
incorrectly Master Codes enrolled or PIN codes attempted.
EPROM: Non-volatile memory, System will retain all programs and codes after a total
loss of power.
Output: Dual relay, N.O./N.C./Com. Output (free voltage contact) 、Tamper switch
Relay Activation Time: （＊10、＊20）
Strike Time: 1~99 seconds（adjustable）
Strike mode: Access Timer or Latch
Color: Dark gray/ Beige White

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG30 Ver. A Publish:2004.08.26 Page: 2/ 4
3. The indicator signal chart:
Sound and LED indicator:
Red LED Power on
Green LED Relay activated
Tri-color-Yellow Entering the Program mode
Tri-color-Red Slot position is registered
LED signal
Tri-color-Green Slot position is ready to register
1 Beep Slot position is ready to register、Effective card（PIN
codes）、Exit from the Program mode
2 Beeps Entering the Program mode
3 Beeps Slot position is registered 、Data computing error 、other
operation mistakes、duplicate card
Sound signal
5 Beeps Master Code reset to Factory （12345）
Factory Parameter list：
Format 26 bits
Card register None
Master Codes 12345 (5 digits)
Strike Time 1 seconds
Pressed key delay time (Time Out) 5 seconds
Program mode delay time 60 seconds
Invalid PIN Lock-out time 60 seconds
4. Operation Instruction:
Enter Program Mode:
1. Compose twice the master code (Factory master is 「12345」)
→2 beeps and the Yellow LED will light up
→you are now in the "programming mode".
2. Note: After 60 seconds if you have not entered any codes or data, the system will
automatically exit from the programming mode. After 6 wrong attempts at the master
code the lockout facility will operate.
Exiting from the program mode:
1. Press「#」to exit from the programming mode.
2. Note: After 60 seconds if you have not entered any codes or data, the system will
automatically exit from the programming mode. After 6 wrong attempts at the master
code the lockout facility will operate.
Selecting The User Format
Enter the Programming mode, Press「＊30」
Followed By「01」：This will set the system to be used as :Wiegand 26-bit；Slots
001~100 for cards/tokens and slots 01~150 for PIN codes
OR
Followed By 「02」：This will set the system to be used as : Wiegand 34-bit, Slots
001~100 for cards/tokens and slots 01~150 for PIN codes
OR

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG30 Ver. A Publish:2004.08.26 Page: 3/ 4
Followed By 「03」：This will set the system to be used as : Slots 001~150 for PIN
codes only
Note: When system format has the change, there’s a possibility the card stored would be
invalid. Please reset the system and input all cards /tokens.
Add card and deletion
Enter the Programming mode, Enter the slot position code 「001~100」
A. Green light comes on: This slot position is ready to register the card
1. Present card in front of the readerÆYellow LED blinks (beep) Æenrolled
completed Æ（repeat）
2. Present card in front of the readerÆ(3 audible beeps) another card has already
been input (duplicate card).
B. Red light comes on: This slot already has a code registered
1. Press「＊＊」(deletion) ÆGreen light ÆEnter the slot position code again
ÆPresent the card in front of the reader Æ﹝same as Step “A”﹞
2. Enter another slot card position
Add PIN codes and deletion
Enter the Programming mode, Enter the slot position code 「101~150」
A. Green light comes on: This slot position code may register the PIN codes
Input 5 digit PIN codes ÆYellow LED blinks (beep) Æenrolled Æ（repeat）
B. Red light comes on: This slot position code is registered
1. Press「＊＊」(deletion) ÆGreen light ÆPress the slot position code again Æ
Input 5 digit PIN codes Æ﹝same as Step “A”﹞
2. Enter another slot card position
Note 1: The codes"12345" or master code are not be used for PIN code.
Note 2: PIN codes operate open door：「???????????＊＊＊＊＊＃」
「???….」random codes,「＊＊＊＊＊」5 digit PIN codes,「＃」Enter
To Program Relocking Timer
Enter the Programming mode,
A. Relay 1：Press「＊10」Followed by the number of seconds the relay should
open→「05」=5 seconds（01 ~99 = seconds）→（beep）→enrolled →Press
「#」to exit from the programming mode, or program other operating.
B. Enter「00」Sets the relay to latching mode. (Correct code entered opens the relay,
and the relay stays open until the correct code is entered again).
C. Relay 2：Press「＊20」Followed by the number of seconds the relay should
open）→「05 =5 seconds (01 ~99 = seconds). →（beep）→enrolled →Press
「#」to exit from the programming mode, or program other operating.
D. Enter「00」Sets the relay to latching mode. (Correct code entered opens the relay,
and the relay stays open until the correct code is entered again).
Changing the Master codes:
Enter the Programming mode, Enter「＊00」Followed by the new 5 digit master
code→（beep）→enrolled→Enter 「#」to exit from the programming mode, or
program other operating.

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG30 Ver. A Publish:2004.08.26 Page: 4/ 4
Reset to Factory
Master Code reset to Factory 「12345」
Insert the jumper RES1Æ1-2 positionÆ5 audible beepsÆReset successfulÆReturn
Insert the jumper to 2-3 position
Remove all stored information
Insert the jumper RES1Æ1-2 positionÆ5 audible beepsÆMaster Code reset to
Factory 「12345」Æafter 5 secondsÆ5 audible beepsÆRemove all stored
information ÆReturn Insert the jumper to 2-3 position.
Note: If you only wish to reset the Master Code to the Factory default, remove the
jumper after exactly 5 audible beeps, otherwise all cards / codes will be deleted.
5. Wiring diagram:
123
+12V
GND
DATA
CLK
BUZZER
+5V
A
uxiliaryReader
(Wiegand26or
34-bitFormat)
AuxiliaryReader
(Data/CLKFormat)
Tofollow the
precedentof
Group1contacts
Tamperswitch
contactoutput
(freevoltage
contact)
Tamper
Switch
Push Button
FAIL-SAFE
LOCKING DEVICE Power Supply
Re-set of all
system parameter
Contact door reed switch
This reed switch is used
to reset the re-locking time
to 0 second when the door is moved.
(Using N.O. contact in case of door closed,
changeover to N.C. When door is moved)
Note:
DG-30 controller and auxiliary reader distance must not exceed 20 meters; the data will
not transmit beyond this. The suggested wire gauge is #22~26 AWG.
Using a Linear supply power recommended, to prevent power reduction at the card
reader.
The varistor or diode must be connected across the lock terminal (electromagnet...)
operated by the device. The vartistor controls the overload produced by the strike coil
(EMP).
Egresses switch should be N.O. type.