Genie Car2U Operating instructions

User Manual of Product 1:
Genie ChainMax 1000 Garage Door Opener - Durable Chain
Drive - Includes two 3-Button Pre-Programmed Remotes, Wall
Console, Wireless Keypad, Safe-T-Beams - Model 3022-TKH,
140V DC Motor

Car2U®System
Programming for Genie®
Setting the Car2U to Factory Default settings
The default setting for the Car2U system is:
•Button 1= Genie Manufactured Openers
•Button 2= LiftMaster®Manufactured Openers
•Button 3= Wayne Dalton®Manufactured Openers
1. Press and hold buttons 1 and 3 for twenty seconds or until all three LED’s begin to
flash.
2. Release both buttons. The Car2U system is now set to the Factory Default
settings.
123
To Change One of the Other Manufacturer’s Buttons to Genie
1. Press and hold buttons 1 and 3 for one second and release– all three LED’s will
light solid RED.
2. Press and hold the button (2 or 3) you want to change to Genie – the corresponding
LED will flash. While continuing to hold the button you want to change, press and
release button 1. Press and release button 1 again.
3. Release the button you were holding in step 2 and wait for the LED to stop flashing.
This button is now set for Genie.
Note: If needed, repeat this procedure for the remaining button to change to Genie
1

Car2U®System Programming for GENIE Models
Programming Car2U to a Genie Opener
1. Press and hold the program button until the round blue LED and the long
blue LED are on – release the button. The round blue LED will be on.
2. Press the program button once - the long purple LED will begin flashing
3. Press a previously learned Intellicode®2 transmitter button
from model G3T
(
pictured ri
g
ht
)
one time. Both the lon
g
and round
LEDs flash purple.
4. Press the desired Car2U button for one second and release. Both the long and
round LEDs go solid purple.
5. Press the desired Car2U button (again) for one second and release. Both the long
and round LEDs change from solid purple to solid blue and then go out.
6. Pressing the Car2U button again will cause the garage door to move.
NOTE: If you cannot find your program button on the power head, see the user manual
for your opener or visit the Genie website for additional assistance.
2
IntelliG®1000, IntelliG®1200, TriloG™1200, TriloG™1500, GPower™900
Manufactured before July 2011
The label shown right is on the back of
the powerhead. Use this instruction if
the first 5 digitsof the serial number
from this label is 11188 or smaller.
PRGM
PRGM

Car2U®System Programming for GENIE Models
Programming Car2U to a Genie Opener
1. Press and hold the program button until the round blue LED and the long
blue LED are on – release the button. The round blue LED will be on.
2. Press the program button once - the long purple LED will begin flashing
3. Press the desired Car2U button for one second and release. Press that same
button again for one second and release. The long LED will flash blue and then
turn off.
4. Pressing the Car2U button again will cause the garage door to move.
NOTE: If you cannot find your program button on the power head, see the user manual
for your opener or visit the Genie website for additional assistance.
3
IntelliG®1000, IntelliG®1200, TriloG™1200, TriloG™1500, GPower™900
Manufactured before November 2011
The label shown right is on the back of
the powerhead. Use this instruction if
the first 5 digitsof the serial number
from this label is 11290 or smaller.
PRGM
PRGM

Car2U®System Programming for Genie Models
Programming Car2U to a Genie Opener
1. Press and hold the program button until the round blue LED is on –
release the button. The long LED willflash purple.
2. Press the desired Car2U button for one second and release. Press that same
button again for one second and release. The round LED and long LED will
both turn blue and then turn off.
3. Pressing the Car2U button again will cause the garage door to move.
NOTE: If you cannot find your program button on the power head, see the user manual
for your opener or visit the Genie website for additional assistance.
PRGM
4
IntelliG®1000, IntelliG®1200, TriloG™1200, TriloG™1500,
GPower™900, ReliaG® 650, ReliaG®850
Manufactured after November 2011
The label shown right is on the back of
the powerhead. Use this instruction if
the first 5 digitsof the serial number
from this label is 11291 or greater.

Car2U®System Programming for older Genie Models
Programming Car2U to a Genie Opener
1. Press and release the learn code button - the red LED will begin to blink.
2. Press the desired Car2U button one time. The red LED will stop blinking and stay
on.
3. Press the desired Car2U button one more time. The red LED will go out.
4. Pressing the Car2U button again will cause the garage door to move.
NOTE: If you cannot find your program button on the power head, see the user manual
for your opener or visit the Genie website for additional assistance.
If your learn button looks like this:
5

Car2U®System Programming for Genie Models
Programming Car2U to a Genie Opener
1. Press and release the learn code button the red LED will begin to blink.
2. Press the desired Car2U button one time. The red LED will stop blinking and stay
on.
3. Press the desired Car2U button one more time. The red LED will go out.
4. Pressing the Car2U button again will cause the garage door to move.
NOTE: If you cannot find your program button on the power head, see the user manual
for your opener or visit the Genie website for additional assistance.
CODE
6
ChainLift® 600, BeltLift®600, ChainLift® 800, BeltLift®800,
ReliaG 600® ,ReliaG 800®