Genie GCL-MJ User manual

www.GenieCompany.com/commercial | 800.843.4084
GCL-MJ operators are covered by the following U.S. patents: 7355363, 7878931, 8014966
The GCL-MJ is designed for high or full-lift
sectional and rolling doors that have a limited-duty
cycle requirement. Advanced features and robust
mechanical design combine to provide a medium-duty
operator that is the new standard in the industry.
UL325-2010 APPROVED
• Allowsformonitoredentrapmentprotectionandmomentary
operationwhenusedwithselectphotoeyesand/or
edge-sensingdevices.
• Seebackforapprovedlistofmonitoreddevices.
GCL-MJ Advantages
• Ratedfor15cyclesperhouroperation,maximizing
performanceoutofamedium-dutyoperator.
• Modulardesignwithoptionalexpansionboardsforadvanced
timertoclose,andauxiliaryoutputfunctionality.
• Optional:Intellicode®Iplugandplayreceiverlearnsupto50
transmitters.Learnanddeleteindividualtransmittersdirectly
fromLCDdisplay.
• TensiBelt™primarydrivereductioneliminatesneedtoadjust
belttension.
• Availableineither115Vor230VAC1Ø60Hz.Expanded
offeringincreasesapplicationsavailableformedium-dutyuse.
• Motorwithbuilt-inthermalprotectionandballbearingdrive
end.Providesoverloadprotectionandbearingsextendlifeof
motorovertypicalbushings.
• LCDdisplaywithintuitivesetupmenu.Providesreal-time
statusandtroubleshootingassistance.
• Open/close/stopandsetupkeysincludedoncontrolboard.
KeepsallcontrolsneartheLCDdisplayconvenientforsetup.
Standard Features
• Opticallimitsystemwithlineartravelnuts.
• Maxruntimerautomaticallyadjuststoupanddownruntime.
• TensiBelt™primaryreduction.
• Delayonreverse.
• 16-characterLCDdisplay.
• UL325-2010approved.
• 3-buttoncontrolstation.
• 2-year/20,000-cyclewarranty.
• Programmablemid-stop.
• Pull-cordreleaseforemergencymanualoperation.
GENIE® COMMERCIAL OPERATORS
GCL-MJ
MEDIUM-DUTY JACKSHAFT OPERATOR

www.GenieCompany.com/commercial | 800.843.4084
©2012 The Genie Company | GCL-MJss
13 7
8
"
63
4
" 73
16
"
65
8
"
SECTIONAL WALL MOUNT
10 15
16
"
33
4
"
315
16
"
19 5
8
"
17"
19 5
8
"
18 1
2
"
9
16
"
8"
2"
12"
97
16
"
47
8
"
MOUNTING DIMENSIONS
REVISIONS
ER REV DESCRIPTION DATE APPROVAL
501348 -
ORIGINAL ISSUE
D
C
B
A
A
B
C
D
1
2
3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
GMXJ TECHNICAL INFO
-
NOTES: (UNLESS OTHERWISE SPECIFIED)
11/10/11
FINISH
MATERIAL
HOLES:
< Ø.251 = .003
Ø.251-Ø.500 =
.003
> Ø.500 =
.003
112213
INCHES
WDR 10/19/2011
WDR 11/9/11
DO NOT SCALE
A SUBSIDIARY OF OVERHEAD
DOOR CORPORATION
TOLERANCES:
DRAWN
112213-GMXJ-SECT
INTERPRET DIMS & TOLS
PER ASME Y14.5M
DIMS CIRCLED WITH
SYMBOL '

' ARE CRITICAL
TO QUALITY DESIGN
FEATURES & MUST MEET
APPLICABLE IN-PROCESS
INSPECTION STANDARDS.
ALL DIMS ARE IN
UNLESS OTHERWISE SPECIFIED
SCALE 1:2
DWG NO. SIZE
DESCRIPTION
APPROVALS
DATE
ALL GEOMETRY GOVERNED BY 3D CAD DATABASE :
APPROVED
CHECKED
.X = ±.1
.XX = ±.01
.XXX = ±.005
ANGULAR = ±1
SHEET 1 OF 2
THIRD ANGLE PROJECTION
ALLIANCE, OHIO
D
PLOTTED: 10/19/11
MS
THE DRAWINGS AND ALL OTHER
INFORMATION CONTAINED HEREIN ARE
THE CONFIDENTIAL PROPRIETARY
PROPERTY OF OVERHEAD DOOR
CORPORATION, INCLUDING ITS
AFFILIATED SUBSIDIARIES AND
AFFILIATES. THIS DRAWING
INFORMATION, IN WHOLE OR IN PART,
MAY NOT BE COPIED IN ANY MANNER OR
DISCLOSED TO ANYONE WITHOUT PRIOR
WRITTEN CONSENT OF OVERHEAD DOOR
CORPORATION. DISCLOSURE OF ANY
DRAWING OR INFORMATION IS INTENDED
NOT TO AND SHALL NOT OPERATE AS A
LICENSE OR AUTHORIZATION TO USE IT
FOR ANY PURPOSE WITHOUT SPECIFIC
WRITTEN CONSENT OF OVERHEAD DOOR
CORPORATION.
P/N 112213-0001
GCL-MJ |MEDIUM-DUTY JACKSHAFT OPERATOR
1.MaxDoorWeightandnotthesquarefootage,isthecriticalfactorinselectingtheproperoperator.
2.MaxDoorHeight16’
3.For“CommercialSteelInsulated”category,various“backer”optionsareavailable.Thechartaboveisbasedinallcasesonthethickestbackeravailable.
4.“PU-FIP”standsfor“polyurethane,foamed-in-place.”Ifnonotationispresent,insulationis“polystyrenelaid-in-place.”
Notes:
Accessories and Options
• TimertoCloseModule
TimedclosesetviatheLCDdisplayfrom2secondsupto5minutes.
Includespre-closewarningcontacts,timerholdinput,auxiliaryopen
input,normallyclosedsafetyinput,andmonitorededgeinput.
• AuxiliaryOutputModule
Providesrelaycontactsattheopen,close,andmid-stoplimits.Contacts
for5-minutelamp,and“ADA”contactssetviaLCDdisplaytowarnduring
opening,closingorboth.
• 315MhzReceiverModule
IntelliCode®Iradioreceiverthatis315Mhzandcapableofstoring50
single-buttonand/or50open-close-stoptransmitterswiththeabilityto
addand/ordeletetransmittersindividually,identifyandstoreactivating
transmitterID(s).
• UL325-2010ApprovedReversingDevices
Theinstallationofamonitoredexternalentrapmentdeviceisrequired
formomentarycontactcloseoperationonallcommercialdooroperators.
Onlythefollowingdevices,whenpurchasedthroughGenie,areUL-
Approvedforusetomeetthisrequirement:
• Safe-T-Beam®PhotoeyeKitwithadjustablebracket
P/N38176R.S1
• Impact-protectedCommercialPhotoeyeKitP/NOPAKPE.S
• MillerEdgeME/MT/CPT(DCorT3)2-wireedgesensor.Mustbe
usedwithTCM(OPABTCGX.S)orInterfaceModule(OPAKMEIGX.S).
• Nema4PhotoeyesP/NOPAKPEN4GX.S
1— Default device when operator is ordered.
Construction
• Motor
1/2HP,ACcapacitorstart/runmotor.Motorreplaceablewithout
changinglimits.
• Brake
ACsolenoid-actuatedbandbrake.
• Drive
Primary—TensiBelt™autotensioningPoly-VJbelt.
Secondary—chainandsprocketreduction.
• FrictionClutch
Adjustableclutchtohelpprotectagainstdoorand
operatordamage.
• PrecisionRadialBallBearings
Includedincriticalareasthroughoutthepowertrain.
• EmergencyManualOperation
Pull-corddisconnectdisengagesdriveallowingdoortobemoved
manuallywhilemaintaininglimits.
• Pre-wiredtoaccept:
-Monitoredentrapmentdevicesuchasphotoeyes.
-Singleor3-buttoncontrolstations.
-Externalinterlockswitches.
MAX DOOR SIZE (SQ*FT) - SECTIONAL
Door Series
CommercialSteelInsulated&Non-Insulated Thermospan®ThermoMark™Aluminum
216 216
Ins. 220 220 Ins. 2415 2415 Ins. 2411 2411 Ins. 125 150 200 200-20 5150 5200 451 452
Flush Ribbed Insulated Insulated
Model
Max
Door
Wt.
(lbs.)
16GA. 16GA.
Ins.
20GA.
Steel
20GA.
Ins. 24GA. 24GA. Ins.
Nominal
24GA.
Nominal
24GA.
Ins.
PU-FIP PU-FIP
1.38”
PU-FIP
2”
PU-FIP
2”
20GA.
Ext.
PU-FIP
Raised
Panel
1.38”
PU-FIP
Raised
Panel
2”
1/8”
Glass
1.38”
1/4” or
1/2”
Glass
1.38”
1/2 HP 620 170 120 230 160 270 200 300 256 256 256 240 160 256 256 210 144
MAX DOOR SIZE (SQ*FT) - ROLLING
Door Series SteelNon-Insulated SteelInsulated CounterDoors Grilles SheetDoor
16GA. 18GA. 20GA. 22GA. 24GA. 26GA. 18GA. 20GA. 22GA. Aluminum STL/SST Aluminum STL/SST 26GA.
Model
Max
Door
Wt.
(lbs.) 197 246 246 338 394 394 148 148 197 126 126 300 200 256
1/2 HP 580
Dealer Imprint Area
AMPERAGE RATING 1Ø 60Hz
HP 115V 230V
1/2 6.5 3.1