Genie Pro Stealth User manual

Automatic
Chain Drive/Belt Drive
Garage Door Operator
System
Owner’s Manual
SAVE FOR FUTURE REFERENCE
Customer Service
CALL: 1-800-354-3643
VISIT: WWW.GENIECOMPANY.com
GPS-IC Series
PMX-IC B Series
AUTOMATIC GARAGE DOOR OPERATOR SYSTEMS
HANG MANUAL NEAR YOUR WALL CONTROL
Complete with Remote Control
and SERIES II Electronics
Operator MUST be installed with the included SERIES II Wall Control!
Self-diagnostic Electronic Sensory Protection System
(SAFE-T-BEAM SYSTEM) MUST Be Installed To Close Door!

“ ”
“ ”
2
’
®( )
" “ ”
“ ”

3
®
”
SECTIONAL DOOR ONE-PIECE DOOR

4
OVERVIEW OF
POTENTIAL HAZARDS
POTENTIAL
HAZARD
EFFECT PREVENTION
®
®
®
®
1. READ AND FOLLOW ALL SAFETY, INSTALLATION AND
OPERATION INSTRUCTIONS. If you have any questions or
do not understand an instruction, call your service
representative.
2. Do Not install operator on an improperly balanced door. An
improperly balanced door could cause severe injury. Repairs
and adjustments to cables, spring assembly, and other
hardware must be made by a trained service person using
proper tools and instructions.
3. Remove all ropes and disable all locks connected to the
door before installing operator.
4. Install door operator 7 feet or more above the floor. Mount
the emergency release knob 6 feet above the floor.
5.Do Not connect the operator to the source of power until
instructed to do so.
6. Locate the control button:
• Within sight of door.
• At a minimum height of 5 feet, so small children cannot
reach it.
• Away from all moving parts of the door.
7. Install the entrapment WARNING label next to the wall
button or console. Install the emergency release tag on, or
next to, the emergency release
8. The operator must reverse when the door contacts a 1-1/2
inch high object on the floor at the center of the doorway.
This is about the size of a 2”x 4”board laid flat.

” ”
” ”
”
” ” ”
”
”
” ”
”
5

2
3
4
567
8
9
10
1
12
13
14
15
16
17
18
19
20
11
22
23
24
25
26
27
28
29
30
21
32
33
34
35
36
37
38
39
31
40
12
12
12
12
11
19
3
12
26
26
6
”
”
”
”
”
”

7
”
”
”
2
10
12
46
12
12
3
12
45
47
5
6
712
48
12
11
12
40
39
37
4
52 64
3
12
65
28
63
41
42
25
43
13
11
49
53
33
35
50
54
57
58
59
60
59
61
59
58
30
44
8
62
51
52
53
56
55
1
9

’ ”
’
’
’
’ ” ’
’
’ ” ’
’
’ ” ’
’
’
8
’ ” ”
’ ”
’ ”
’ ”
”
”
”
” ”
’ ” ”
’ ”
’ ”
”
’ ” ”
’ ”
’ ”
”
”
” ”
”
81
69
71
71
71
73
74
75
76
77
78 79 80
83
71
92
93
90
96 89
95
82
66 85
98
86
97
87
88 90
89 99
71
94
91
70
71
83
84
69 67
68
67
79
72

9
”
” ”
” ”
” ”
” ”
”
” ”
”
68
88
90
95
96
89
93
91
92
115
94
114
86
110
12 2
121
112
69
73
76
117
120
113
123
90
89
97
87
82
80
79
116
81
119
118
111
”
79

”
” ”
“ ”
“”
•
• “ ” “ ”
• “ ”
•
• ”
•
•
•
•
•
•
“ ”
”
” ”
10
“”
•
• “ ” “ ”
• “ ”

•
” ” ”
•
•
“ ” “ ”
“ ”
“ ”
“ ”
11
1. READ AND FOLLOW ALL SAFETY, INSTALLATION AND
OPERATION INSTRUCTIONS. If you have any questions or
do not understand an instruction, call your service
representative.
2. Do Not install operator on an improperly balanced door. An
improperly balanced door could cause severe injury. Repairs
and adjustments to cables, spring assembly, and other
hardware must be made by a trained service person using
proper tools and instructions.
3. Remove all ropes and disable all locks connected to the
door before installing operator.
4. Install door operator 7 feet or more above the floor. Mount
the emergency release knob 6 feet above the floor.
5. Do Not connect the operator to the source of power until
instructed to do so.
6. Locate the control button:
• Within sight of door.
• At a minimum height of 5 feet, so small children cannot
reach it.
• Away from all moving parts of the door.
7. Install the entrapment WARNING label next to the wall
button or console. Install the emergency release tag on, or
next to, the emergency release.
8.The operator must reverse when the door contacts a 1-1/2
inch high object on the floor at the center of the doorway.
This is about the size of a 2” x 4” board laid flat.

•
•
•
•
•
•“ ”
– ”
–
– ”
•
•
•
• ”
•
•
•”
• “ ” “ ”
”
“ ”
“ ”
“ ”
”
“ ”
“ ”
12

•“ ”
•
•
•
•– “ ”
– “ ”
• “ ” “ ”
• ”
• ” ”
•
•
•–
–
–
•
•
•
•“ ”
“ ”
“ ”
“ ”
“ ”
13

•
•–
–
•
–
–
•–
– ”
•” ”
–
–
•
•
•
®
”
“ ” “ ”
“ ”
“ ”
“ ”
“ ”
14
OR
” ”
” ”
” ”

•
•
•“ ”
– ”
–
– ”
•
•
•
•
•
•
•– “ ”
– “ ”
• “ ” “ ”
• ”
•” ”
“ ”
“ ”
“ ”
“ ”
“ ”
“ ”
” ”
” ” ” ”
” ” ” ”
•
• “ ” “ ”
15

•
•
•
•
•
•
–
–
–
16
“ ”
“ ”
“ ”
“ ”
OR

•“ ”
•
•
•
•
•” ”
•
•
–
–
•
•
•–
–
•
•
17
” ”
d_39905_38124_14.0

•–
–
•
––
•
•
•–
–
®
• ”
•–
–
•
•
®
F
’
”
Sensor
Source
Red
Green
Power
Head
Sensor
Source
Red
Green
Power
Head
AB
Dashed Line = striped wire
Solid Line = white wire
SUN
ONE DOOR
GARAGE
THREE DOOR
GARAGE
RED
LED
RED
LED
GREEN
LED
RED
LED
GREEN
LED
GREEN
LED
GREEN
LED
RED
LED
RED
LED
RED
LED
GREEN
LED
GREEN
LED
TWO DOOR
GARAGE
18
®

• ’
–
–
–
•– ’
– ’
•
• ” ”
NOTE: STB alignment check must be performed
following connection to electrical power (see page 21).
DO NOT PLUG IN YET!
” ”
2
3
3
4
19
ON ON NORMAL OPERATION NONE REQUIRED
OFF OFF 1.POWER HEAD NOT POWERED
2.WIRING FROM POWER HEAD BAD
1.CHECK BREAKERS, FUSES, PLUGS
2.CHECK WIRING FOR OBVIOUS SHORTS
OFF ON 1.WIRING TO SOURCE MISSING OR BAD
2.POWER HAS BEEN INTERRUPTED
1.CHECK WIRING
2.REMOVE POWER AND REAPPLY
2 BLINKS, PAUSE (REPEAT) ON 1.BEAM NOT ALIGNED 2. BEAM OBSTRUCTED
3.SENSOR DEFECTIVE
1.CHECK ALIGNMENT 2. CHECK FOR OBSTRUCTION
3.CALL CUSTOMER SERVICE
1.WIRE TO SENSOR MISSING OR BAD
2.SENSOR DEFECTIVE
1.CHECK WIRING
2.CALL CUSTOMER SERVICE
OFF
ON 1.SENSOR RECEIVING INTERFERENCE 1.
ATTEMPT TO DETERMINE SOURCE OF INTERFERENCE
2.CALL CUSTOMER SERVICE
ON 1.SOURCE NOT SENDING PULSES
2.SOURCE DEFECTIVE
1.CALL CUSTOMER SERVICE
2.CALL CUSTOMER SERVICE
2 BLINKS, PAUSE (REPEAT)
3 BLINKS, PAUSE (REPEAT)
4 BLINKS,PAUSE (REPEAT)
Safe-T-Beam®Alignment Check
After turning the electrical power on, if the
STB’s are not in proper alignment, the red
LED (Source) will blink continuously.
To correct the problem – the brackets are
flexible and can be adjusted slightly to bring
the system into alignment.
When the STB’s are in alignment the red LED
will stop blinking and stay on.

”
MORE
MENT
OPEN
PUSH
L MITS
TO SET
G4
Y3
2
W1
•–
–
–
•
”
•
– “ ”
“ ”
– “ ”
“ ”
– “ ”
“ ”
– “ ”
“ ”
•
•
•
•
NOTE: Additional wall controls are available from your
dealer. ONLY ONE OF YOUR WALL CONTROLS MAY BE
THE LIGHTED TYPE. If you have a lighted wall control, all
your additional controls must be un-lighted. More than one
lighted wall control per operator will cause a malfunction.
•
•
1
2
3
4
W
B
BW
1
2
3
4
NEC
1
2
3
4
5
6
MORE
FORCE

S
BE
LIM T
SET
OPEN
FOR E
CLO E
FOR E
RAD O
SIG AL
LEA N
CODE
CO
DO N T
USH
L M T S 
UN E S
D OR I 
ATCE
NO E
U E N Y
SER E CON ROLS

CLOSE
MORE
OPEN
MORE
SE OPEN
IMIT ADJUSTMENT
U S Patent o 5 243 784
5 21 869


1
2
3








CODE





E:
ONL W

LO  
L


W
B
BW

1
2
3
5



LIMIT




NOT




USE ON Y
SERIES II C


MO E



20
–
–
–
–
–
–
–
–
1
4
3
2