Genius Brain 17 User manual

BRAIN 17
BRAIN 17

BRAIN 17 2 732788 - Rev. A_1
ENGLISH
CE DECLARATION OF CONFORMITY
Manufacturer: FAAC S.p.A.
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA- ITALY
Declares that: BRAIN 17 remote Programmer
conformstotheessentialsafetyrequirementsofthefollowingEECdirectives
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility Directive
Additional note:
this product underwent tests in a typical uniform configuration
(all products manufactured by FAAC S.p.A.).
Bologna, january the 1st 2013
The Managing Director
A. Marcellan

BRAIN 17 3 732788 - Rev. A_1
ENGLISH
WARNINGS FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS
13. Makesurethattheearthingsystemisperfectly
constructed, and connect metal parts of the
means of the closure to it.
14. Theautomatedsystemsthatfeatureabuilt-inanti-
crushing safety device in any case require a
functional check in accordance with the pro-
visions of the Standards indicated at point 9.
15. Thesafetydevices(EN12978standard)protect
any danger areas against mechanical mo-
vement Risks, such as crushing, dragging,
shearing, lifting.
16. Useofatleastoneindicator-light(e.g.:flashing
lamp) is recommended for every system, as
well as a warning sign adequately secured.
17. FAACS.p.A.declinesallliabilityasconcernssa-
fety and efficient operation of the automated
system, if system components not produced
by FAAC S.p.A. are used.
18. Formaintenance, strictly useoriginal partsby
FAAC S.p.A.
19. Donotinanywaymodifythecomponentsofthe
automated system.
20. TheinstallershallprovidetheUserwithallinfor-
mation concerning manual operation of the
system in case of an emergency.
21. Donotallow children oradultsto stay nearthe
product while it is operating.
22. Keepradio controls or other pulsegenerators
awayfrom children, to prevent theautomated
system from being activated involuntarily.
23. Transit isallowed only whentheautomation is
fully open.
24. TheUsermustnotattemptanykindofrepairor
direct action whatever and contact qualified
personnel only.
25. Anythingnotexpresslyspecifiedintheseinstruc-
tions is not permitted.
1. ATTENTION!Toensure the safetyofpeople,it
is important that you read all the following
instructions.Incorrect installation or incorrect
use of the product could cause serious harm
to people.
2. Carefullyreadtheinstructionsbeforebeginning
to install the product.
3. Donotleavepackingmaterials(plastic,polystyre-
ne, etc.) within reach of children as such
materials are potential sources of danger.
4. Store the instructions for future reference.
5. Thisproduct was designed andbuiltstrictly for
the use indicated in this documentation. Any
otheruse, not expresslyindicated here,could
compromise the good condition/operation of
the product and/or be a source of danger.
6. FAACS.p.A.declinesallliabilitycausedbyimpro-
per use or use other than that for which the
automated system was intended.
7. Donotinstallthe equipment in an explosive at-
mosphere: the presence of inflammable gas
or fumes is a serious danger to safety.
8. FAAC S.p.A. is not responsible for failure to
observe Good Technique in the construction
ofthe closing elementsto be motorised, or for
any deformation that may occur during use.
9. The installation must conform to Stan-
dards EN 12453 and EN 12445.
For non-EU countries, to obtain an adequate
levelof safety, the Standards mentioned abo-
ve must be observed, in addition to national
legal regulations.
10. Beforeattemptinganyjobonthesystem,cutout
electrical power and disconnect the batteries
if present.
11. Themainspowersupplyoftheautomatedsystem
mustbe fitted withan all-poleswitch with con-
tact opening distance of 3mm or greater. Use
of a 6A thermal breaker with all-pole circuit
break is recommended.
12. Makesurethatadifferentialswitchwiththreshold
of 0.03 A is fitted upstream of the system.
MEANING OF THE SYMBOLS USED
Important for the safety of persons and for the
good condition of the automated system. Notes on the characteristics and operation of the product.

BRAIN 17 4 732788 - Rev. A_1
ENGLISH
INDEX
CE DECLARATION OF CONFORMITY.....................................................................................2
WARNINGS FOR THE INSTALLER...........................................................................................3
1. TECHNICAL SPECIFICATIONS............................................................................................5
2. PREPARING FOR INSTALLATION.......................................................................................6
3. BOARD LAYOUT...................................................................................................................6
4. ELECTRICAL CONNECTIONS.............................................................................................8
4.1 J1 - MAINS PRIMARY POWER SUPPLY .........................................................................8
4.2 J2 - MOTORS AND FLASHING LAMP.............................................................................8
4.3 J3 - LOW-VOLTAGE ACCESSORIES - INPUTS/OUTPUTS............................................9
4.4 J12 - PROGRAMMABLE OUTPUTS - ELECTRIC LOCKS .............................................10
4.5 J12 -J6 - LIMIT SWITCH AND TIMECODER....................................................................10
4.6 J10 - BUS G-WAY ACCESSORIES .................................................................................11
4.7 J5 - RQFZ MODULE RAPID CONNECTOR............................................................................14
4.8 TRADITIONAL PHOTOCELLS .........................................................................................15
5. PROGRAMMING ...................................................................................................................18
5.1 BASIC PROGRAMMING FUNCTIONS.............................................................................19
5.2 ADVANCED PROGRAMMING FUNCTIONS....................................................................24
5.3 BUS G-WAY DEVICE INSTALLATION .............................................................................27
5.3.1 BUS G-WAY DEVICE ENTRY.......................................................................................27
5.4 TIME LEARNING - SETUP................................................................................................29
5.5 TESTING THE AUTOMATED SYSTEM............................................................................30
6. MEMORISING THE RADIO CODE........................................................................................31
6.1 MEMORISING THE JLC RADIO CONTROLS..................................................................31
6.2 MEMORISING RC RADIO CONTROLS (ONLY 433 MHZ)...............................................32
6.2.1 REMOTE MEMORISATION OF RC RADIO CONTROLS.........................................33
6.3 DELETING THE RADIO CONTROLS...............................................................................33
7. START-UP..............................................................................................................................34
7.1 CHECKING THE LEDs......................................................................................................34
8. SIGNALLING ERRORS AND ALARMS................................................................................35
8.1 ERRORS............................................................................................................................35
8.2 ALARMS............................................................................................................................36
9. TROUBLESHOOTING...........................................................................................................36
10. MANAGING THE CONFIGURATION FILE – J8 USB .......................................................37
11. FUNCTION LOGICS ............................................................................................................40

BRAIN 17 5 732788 - Rev. A_1
ENGLISH
CONTROL BOARD BRAIN 17
We thank you for having chosen one of our products. GENIUS is certain that from it you will obtain
all the performance you require. All our products are the result of years of experience in the field of
automated systems.
Mains power supply With power supply switching 230 V~ ± 15% ; 50/60Hz
Power absorbed from mains Stand By = 4W ; MAX about 800 W
MAX load for motors 800 W
Accessories power supply 24 V"
MAX. accessories current +24V MAX 500 mA BUS G-WAY MAX 500 mA
LOCK (GENIUS) 12 V~ / 24 V"
Operating ambient temperature from -20°C to +55°C
Power supply safety fuses F1 = 2,5 A
Work time Self-learned through SETUP - (Max 4 min and 10 sec)
Pause time Programmable (from 0 to 9 min and 50 sec)
Motor power Programmable on 50 levels
Connector inputs RQFZ433/868 Module, USB
Terminal board inputs Mains power supply, BUS G-WAY, OPEN-A, OPEN-B, STOP, Photocells during closing, Photocells during ope-
ning, Limit switch
Terminal board outputs Flashing lamp, Motors, Electric lock (LOCK), W.L. (pro-
grammable), Accessories power supply, failsafe negative
(TX FSW)
1. TECHNICAL SPECIFICATIONS
PURPOSE: this electronic control board has been designed and built to control swing-leaf and/or
sliding gates for vehicle and pedestrian access control.
During programming you can choose between different function logics.
2 programming levels are available from the board (BASIC andADVANCED), using buttons and LCD
display.
Tab. Technical specifications

BRAIN 17 6 732788 - Rev. A_1
VOLTAGE
USB
USB-A
BUS MON.
RADIO2RADIO1
ERROR
HIGH
AREA
STOPLAMP OP-ACOMAC MAIN 24V
1110
OP-B
8
7
CL
M2OP
M1
COM
BUS
212018171615
24V5V
96543
CL
2
OP
1LNPE
J10
LOCK
8.8.
RADIO 433-868
J5
PE N L
1 2 3 4 5 6 7 8 9 10 11 15 16 17 18 19 20 21
RL1 RL2 RL3 RL4 RL5
TH2 TH1
QC4 QC3
IC1
C52
TF1
F1
FL1
LCD1
DB1
+-
/R1 F
/R2
OP-A
OP-B
STOP
DL7DL8
DL9
DL14
DL15
DL16
DL11 DL12
DL10
DL17 DL13
SW3SW1 SW2
121314
12 13 14
CL FSW OP W.L.
TXFSW
19
FSW CL
FSW OP
DL5DL6
22 2324 25
FCA1
DL4
FCC1
DL3
FCA2
DL2
FCC2
DL1
22 23 24 25
FCA1
FCC1
FCA2
FCC2
F1
SW1 SW2 SW3
J1 J2 J3 J11 J8
J5
J6
J10
DL7 DL6 DL5
DL1
DL10
DL11 DL12
DL13 DL14
DL15
DL16
DL17
LCD
DL8DL9
DL2DL3DL4
ENGLISH
3. BOARD LAYOUT
2. PREPARING FOR INSTALLATION
For safety reasons, it is important for people to carefully follow all the warnings and
instructions contained in this manual. Incorrect installation or incorrect use of the
product can causeserious harm to people. Beforeproceeding with product installation,
carefully read the entire manual. Keep these instructions for further reference.
Always cut off the electrical power before carrying out any work on the control unit
(connections, maintenance).
Always separate the power cables from the control and safety cables (button, receiver,
BUS G-WAY encoder, photocells, etc.).Avoid any electrical disturbance using separate
sheathing or a shielded cable (with shield connected to the earth).
• Ensure that upstream of the system there is a suitable magnetothermic differential switch with
omnipolar cut-off, as provided for in current safety regulations.
• Check for the presence of an adequate earthing system.

BRAIN 17 7 732788 - Rev. A_1
ENGLISH
LCD Signalling/Programming display
SW1 “+/R1” Programming button
SW2 “-/R2” Programming button
SW3 “F” Programming button
DL1 “FCC2” Input status control LED
DL2 “FCA2” Input status control LED
DL3 “FCC1” Input status control LED
DL4 “FCA1” Input status control LED
DL5 “FSW OP” Input status control LED
DL6 “FSW CL” Input status control LED
DL7 “STOP” Input status control LED
DL8 “OP-B” Input status control LED
DL9 “OP-A” Input status control LED
DL10 “
USB ” Signalling LED
DL11 “
RADIO1 ” Signalling LED
DL12 “
RADIO2 ” Signalling LED
DL13 “
ERROR ” Error/alarm signalling LED
DL14
“BUSMON” BUS G-WAY diagnostic signalling
LED
DL15 Devicesignalling LED to BUSG-WAYACTIVE
DL16 Microprocessor power presence LED
DL17 +24V"Accessoriespower supply presence
LED
J1 230V~ Power supply connector
J2 Motors and flashing lamp power supply
connector
J3 Input/Output connector
J5
RQFZ433/RQFZ868 receiver module con-
nector
Channel 1
- OPENA (Total Opening)
Channel 2
- OPEN B (Partial Opening)
J6 Limit switch input connector
J8
HOSTUSB-A for Mass Memories connector
J10
BUS G-WAY device connector
J11 W.L. (programmable) and Electric lock
(LOCK) output connector
F1 Motor and power supply safety fuse

BRAIN 17 8 732788 - Rev. A_1
C1 C2
J11J3J2
J1
9 10 11 12 13 14 15 16 17 18 19
20 21
PE N L 1 2 3 4 5 6 7 8
ACMAIN
PE N L M1123 212019
LAMP
78
230V~
MAX 60W
Mot1 Mot2
COM OP CL OP-A OP-B STOP CL FSW OP -
14
-
15
-
16
+
17
+
18910111213 24V
TXFSW W.L. LOCK
M2456
COM OP CL
230V~ ±15%
50/60 Hz
24V
3W
12V~
24V
MAX
100 mA
{
**
J1 J2 J3 J11
{
MAX
500 mA
{
ENGLISH
4. ELECTRICAL CONNECTIONS
4.1 J1 - MAINS PRIMARY POWER SUPPLY
PE Earthing Connection For correct operation, you must con-
nect the switching power supply to the
system’s earthing conductor. Ensure
that upstream a suitable differential
magnetothermic switch has been in-
stalled.
NPowerSupplyConnection230V~±15%Neutral
LPower Supply Connection 230 V~ ± 15% Line
MotorforSINGLE-LEAFor
FIRSTLEAFwhenopening
(closes for the second)
OPEN A
Total gate opening
(contact N.O.)
OPEN B
Partial gate ope-
ning (contact N.O.)
STOP
Gate stop
(contact
N.C.)
*
Blue or grey
Photocells and safety devices:
for connections, see the rela-
ted paragraph.
4.2 J2 - MOTORS AND FLASHING LAMP
1M1 - COM Common contact motor 1 M1=firstleafwhenopeningorsingleleaf
M2 = second leaf when opening - CAN-
NOT be used for single leaf
To verify correct wiring and direction
of motor rotation, (see 5.4 TIME LEAR-
NING - SETUP)
2M1 - OP Opening phase motor 1
3M1 - CL Closing phase motor 1
4M2 - COM Common contact motor 2
5M2 - OP Opening phase motor 2
6M2 - CL Closing phase motor 2
7LAMP Flashing lamp connection (MAX 60 W)
8

BRAIN 17 9 732788 - Rev. A_1
ENGLISH
4.3 J3 - LOW-VOLTAGE ACCESSORIES - INPUTS/OUTPUTS
9OP-A OPEN A contact - N.O.
TOTAL opening Connect a button or other pulse generator which, by closing a contact, commands TOTAL opening of both leaves.
10 OP-B OPEN B contact - N.O.
PARTIAL opening
Connect a button or other pulse generator which, by closing
a contact, commands the PARTIAL opening.
on 2-motor systems = 100% of leaf 1 opening;
on 1-motor systems = 50% of leaf 1 opening.
Whena logic requiring a CLOSE ( b, C) input is selected, the,
OPEN B input automatically becomes CLOSE - N.O. (leaves
closing command).
To install more than one OPEN A or OPEN B pulse generator, connect the N.O. contacts in
parallel (see related Fig.)
11 STOP STOP contact - N.C. Connect a button or other pulse generator which, by opening
a contact, stops movement of the automated system.
To install more than one STOP device, connect the N.C. contacts in series (see related Fig.).
If stop devices are NOT connected, jumper the terminals STOP and GND.
12 FSWCL FSW CL contact - N.C.
closing safety Connect a photocell or other device which, by opening a con-
tact, reverses the movement of the automated system during
opening (FSW OP) or during closing (FSW CL).
13 FSWOP FSW OP contact - N.C.
opening safety
To install more than one safety device, connect the N.C. contacts in series (see related Fig.).
If safety devices are NOT connected, jumper terminals FSW CL and FSW OP and GND if the
FAIL-SAFE safety is not active; otherwise jumper FSW CL and FSW OP and OUT1 (FAIL-SAFE).
14 - GNDAccessories power supply negative15
16
17 + +24 Accessories power supply positive (MAX. load = 500mA)
18
19 TXFSW FAILSAFE negative
Fig. e.g.:Connecting2N.O.contactsinparallel. Fig. e.g.:Connecting2N.C.contactsinseries.

BRAIN 17 10 732788 - Rev. A_1
햲
헁
FCC2
FCC1
FCA2
FCA1
22 23 24 25
J6
J6
햳
FCC2
FCC1
FCA2
FCA1
22 23 24 25
J6
TIMECODER 2
TIMECODER 1
헁
헁
헄
헄
J6
FCC2
FCC1
FCA2
FCA1
22 23 24 25
J6
헁
헁
헄
헄TIMECODER 2
TIMECODER 1
J6 햴
ENGLISH
FCA1, FCC1 and TIMECODER1 correspond to LEAF 1;
FCA2, FCC2 and TIMECODER2 correspond to LEAF 2.
4.4 J12 - PROGRAMMABLE OUTPUTS - ELECTRIC LOCKS
20 W.L. 24 V"(Open Collector)programmableusing the function
SP (advancedprogramming);
default: indicator light
21 LOCK Electric lock (12 V~ or 24 V")
operated 2 sec before opening
of leaf 1
WhenBUS G-WAYencoderis disabled,the electric
lock is operated before each opening (in whatever
position the stopped leaf is in).
When BUS G-WAY encoder is enabled, the electric
lockis operated onlybefore opening theclosed leaf.
4.5 J12 -J6 - LIMIT SWITCH AND TIMECODER
The limit switch contacts FCC1, FCA1, FCC2, FCA2 are all NC contacts.
They are programmable using the functions
FA
and
FC
(basic programming) ; default: disabled.
If no limit switches are used, you DO NOT need to jumper the limit switch contacts
FCC1, FCA1, FCC2, FCA2.
You can however use a single TIMECODER (only for single leaf); in this case, you do
not need to jumper the unused inputs to the earth.
Fig. Limit switch and TIMECODER connections (maximum configuration: 햴).

BRAIN 17 11 732788 - Rev. A_1
ENGLISH
4.6 J10 - BUS G-WAY ACCESSORIES
Thisboard features a BUSG-WAY circuit for facilitatingconnection to thesafety devices ofa highnumber
of auxiliary BUS G-WAY (MAX 16 pairs of photocells), encoder and control devices.
If no BUS G-WAY accessories are used, leave the BUS G-WAY connector free.
BUS G-WAY photocells
Before connecting the photocells, arrange them for the duly address assignment, depending on their
position and operation mode:
Photocells during closing:
trip only during the
closing of the automated system - suitable for
protecting the closing area from risk of impact.
Photocells during opening: trip only during the
opening of the automated system - suitable for
protecting the opening area from risk of impact.
Photocells during opening/closing: trip during
both the opening and closing - suitable for protec-
ting the entire movement area from risk of impact.
Pulse generators: used as pulse generators for
opening the automated system
.
Closing
safety devices Opening
safety devices
Opening/clo-
sing safety
devices

BRAIN 17 12 732788 - Rev. A_1
BUS G-WAY
ENGLISH
Address assignment of BUS G-WAY photocells
To assign the address to each pair of photocells, you must set the Dip-Switches (DS1) located on the
transmitter and corresponding receiver.
The transmitter and receiver of a pair of photocells must have the same
DIP-SWITCH setting.
Two or more pairs of photocells must not have the same DIP-SWITCH setting.
Dip1 Dip2 Dip3 Dip4 TYPE OF PHOTOCELLS
OFF OFF OFF OFF
OPENING (max 6 pairs)
OFF OFF OFF ON
OFF OFF ON OFF
OFF OFF ON ON
OFF ON ON OFF
OFF ON ON ON
ON OFF OFF OFF
CLOSING (max 7 pairs)
ON OFF OFF ON
ON OFF ON OFF
ON OFF ON ON
ON ON OFF OFF
ON ON OFF ON
ON ON ON OFF
OFF ON OFF OFF OPENING and CLOSING (max 2 pairs)
OFF ON OFF ON
ON ON ON ON OPEN PULSE (1 pair)
Connection of BUS G-WAY photocells
For connecting you have to use two cables without polarity (see the specific device instructions).
DL1 = Alignment
DL2 = BUS G-WAY status/
Power supply
DS1 = Programming
Dip-switches

BRAIN 17 13 732788 - Rev. A_1
DL 2
DL 1
DL 2
DL 1
DL 2
DL 1
DL 3
DL 2
DL 1
DL 3
ENGLISH
BUS G-WAY encoder
BUS G-WAY encoder connection is done using the bi-polar cables supplied with.
Connection - Address assignment of BUS G-WAY Encoder
The polarity of the BUS G-WAY line connection determines the correspondence of the
encoder to one leaf or the other.
pay careful attention to the indications of the status LEDs located on the body of each
encoder.
LEAF 1 opens first and closes last.
1 LED on.
On leaf 1 check that, with the
motor stopped, LEDs DL1 and
DL2 are on.
On leaf 2 check that, with the
motorstopped,LEDDL1 is on.
Encoder
Cable Inversion
Encoder
Leaf 1 Encoder Leaf 2
On leaf 1 check that, with the
motor stopped, LEDs DL1
and DL2 are on.
2 LEDs on.
2 LEDs on. 1 LED on.
Note: by inverting the encoder wires, this will
switch around the encoder associated with
leaf 1 and the encoder associated with leaf 2
and vice versa.
On leaf 2 check that, with the
motor stopped, LED DL1 is on.
LEAF 2
LEAF 1
LEAF 1
LEAF 2

BRAIN 17 14 732788 - Rev. A_1
RADIO2RADIO1
ERROR
24V5V
RADIO 433-868
J5
DL16
DL11 DL12
DL17 DL13
ENGLISH
LED ON FLASHING OFF
DL1 Power present
Communication present Power present Communication absent Power absent
Communication absent
DL1 must always be on to confirm correct encoder/board connection.
DL2 Leaf 1 / Leaf 2
DL2 indicates the leaf on which the encoder is installed; it must be on for leaf 1 and off for
leaf 2.
DL3 Stationary leaf Leaf in motion Stationary leaf
DL3 indicatespulse readingduring leaf movement using steady flashing. In stationary status
of the leaf, the DL3 can be either on or off.
In case of incorrect connection (DL2 on or off for both of the encoders), during the
BUS G-WAY accessories learning procedure, the DL1 leds of both encoders are
FLASHING.
Tab. BUS G-WAY Encoder LEDs Status
4.7 J5-RQFZMODULERAPIDCONNECTOR
Plug-inrapidconnectordedicated to RQFZ2-chan-
nel decoding module.
ALWAYS cut off power to the board BE-
FORE inserting/removing the module.

BRAIN 17 15 732788 - Rev. A_1
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 13 14 15 16 17 18 19 20 21
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 13 14 15 16 17 18 19 20 21
ENGLISH
4.8 TRADITIONAL PHOTOCELLS
This board lets you use traditional photocells (contact N.C. with relay).
Before connecting the photocells, it is best to identify the operating type, which depends on the mo-
vement area they have to protect:
Closing photocells:
trip only during the auto-
mated system closing - suitable for protecting the
closing area from risk of impact.
Opening photocells: trip only during the auto-
mated system opening - suitable for protecting the
opening area from risk of impact.
Photocells for opening/closing: trip during both
theopeningand closing -suitable for protectingthe
entire movement area from risk of impact.
Pulse generators: used as pulse generators for
opening the automated system
.
Fail Safe function
This function lets you monitor the correct alignment and operation of the photocells before each move-
ment.ToenabletheFailSafefunction,enter theADVANCED Programming andsetthe
SP
SP =
01
01 function.
With Fail Safe disabled: connect the transmitter (TX) power supply to terminals 15 and
18 of J3.
With Fail Safe enabled:
connect the power supply negative of the transmitters (TX) to
TXFSW . Then jumper the unused safety inputs with TXFSW.
Hereafter are provided the drawings for some connection examples.
Closing
safety devices Opening
safety devices
Safety devices for
opening/closing
No safety device and no stop device
FAIL SAFE disabled No safety device and no stop device FAIL SAFE enabled

BRAIN 17 16 732788 - Rev. A_1
+
헁
헄+
헁
헄
TX CL
RX CL
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 13 14 15 16 17 18 19 20 21
+
+
++
+
+헁
헄
헁
헄
헁
헄
헁
헄
헁
헄
헁
헄
TX CL
RX CL
1
2
5
4
3
1
2
TX OP/CL RX OP/CL
1
2
5
4
3
1
2
TX OP
RX OP
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 1314 15 16 17 18 19 20 21
+
헁
헄+
헅
헄
TX CL
RX CL
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 1314 15 16 17 18 19 20 21
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 1314 15 16 17 18 19 20 21
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 1314 15 16 17 18 19 20 21
ENGLISH
Other
safety
devices
Other
safety
devices
One closing safety device, one opening safe-
ty device, one STOP device.
FAIL SAFE disabled
One pair of closing photocells.
FAIL SAFE disabled
One pair of closing photocells.
FAIL SAFE enabled
One closing safety device, one opening safe-
ty device, one STOP device.
FAIL SAFE enabled
One pair of closing photocells, one pair of
opening photocells and one pair for opening/
closing.
FAIL SAFE disabled

BRAIN 17 17 732788 - Rev. A_1
+
헁
헄+
헁
헄
TX OP
RX OP
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 1112 1314 15 16 17 18 19 20 21
+
헁
헄
+
+
헁
헄
+
헁
헄
헁
헄
TX CL1
RX CL1
1
2
5
4
3
1
2
TX CL2 RX CL2
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 13 14 15 16 17 18 19 20 21
+
+
+
헁
헄
+
헁
헄
헁
헄
헁
헄
TX CL
RX CL
1
2
5
4
3
1
2
TX OP RX OP
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 12 13 14 15 16 17 18 19 20 21
+
+헁
헄
+헁
헄
헁
헄
+
헁
헄
TX CL
RX CL
1
2
5
4
3
1
2
TX OP/CL RX OP/CL
1
2
5
4
3
1
2
LOCK
STOPOP-A W.L. 24V
1110
OP-B 2120181716159LOCK
STOPOP-A 24V
1110
OP-B 2120181716159
TXFSW
19
1412 13
CL FSW OP
9 10 11 1213 14 15 16 17 18 19 20 21
ENGLISH
Other
safety
devices
Other
safety
devices
Two pairs of closing photocells.
FAIL SAFE disabled
One pair of opening photocells.
FAIL SAFE disabled
One pair of opening photocells and one for
closing.
FAIL SAFE disabled
One pair of closing photocells
and one for opening/closing.
FAIL SAFE disabled

BRAIN 17 18 732788 - Rev. A_1
ENGLISH
5. PROGRAMMING
Programming is divided in two levels:
• BASIC programming
• ADVANCED programming
The programming phases are (see Tab.):
1. to access PROGRAMMING;
2. to show the set values and modify them, if you want. Changing the values is effective immediately,
while the final memorisation must be carried out upon exiting programming (St).
3. exitthe programming by using St function.Select Yto SAVEthe configurationyou just performed,
otherwise select no to EXIT WITHOUT SAVING any changes.
You can EXIT programming at anytime:
• press and hold Fand then also
-
to switch directly to St.
F
+
- / R2
Tab. BASIC programming phases.
Tab. ADVANCED programming phases
 
PRESS AND HOLD
F:
THE FIRST
FUNCTION
APPEARS
1
F
RELEASE F:
THE FUNCTION
VALUE IS
DISPLAYED
F
USING
+
OR
-
,
SCROLL THE
AVAILABLE VALUES
UNTIL THE DESIRED
ONE
-/ R2
+/ R1
PRESS F:
TO MOVE TO
THE NEXT
FUNCTION
1
F
FUNCTION St
(LAST FUNCTION)
SELECT YTO SAVE
THE PROGRAMMING
OTHERWISE
SELECT no TO EXIT
THE PROGRAMMING
WITHOUT SAVING
PRESS THE BUTTON
FTO CONFIRM;
AT THE END THE
DISPLAY RETURNS
TO VISUALIZE THE
AUTOMATED SYSTEM
STATUS
F
 
PRESS AND HOLD
FAND THEN ALSO
+
:
THE FIRST
FUNCTION
APPEARS
1
F
+
+/ R1
RELEASE THE
BUTTONS:
THE FUNCTION
VALUE IS
DISPLAYED
F
+
+/ R1
USING
+
OR
-
,
SCROLL THE
AVAILABLE VALUES
UNTIL THE THE
DESIRED ONE
-/ R2
+/ R1
PRESS F:
TO MOVE TO
THE NEXT
FUNCTION
1
F
FUNCTION St
(LAST FUNCTION)
SELECT YTO SAVE
THE PROGRAMMING
OTHERWISE
SELECT no TO EXIT
THE PROGRAMMING
WITHOUT SAVING
PRESS THE BUTTON
FTO CONFIRM;
AT THE END THE
DISPLAY RETURNS
TO VISUALIZE THE
AUTOMATED SYSTEM
STATUS
F

1
1THE FUNCTION IS DISPLAYED UNTIL YOU HOLD

BRAIN 17 19 732788 - Rev. A_1
ENGLISH
5.1 BASIC PROGRAMMING FUNCTIONS
Display Basic Function Default
dF
DEFAULT:
Yindicates that all the set values correspond to the default values.
no indicates that one or more set values are different from the default.
Set Yif you want to restore the default settings.
Y
LO
FUNCTION LOGICS:
ESemi-automatic
EP Semi-automatic Step-by-Step
SP Automatic Step-by-Step Safety Devices
AAutomatic
AP Automatic Step-by-Step
bSemi-automatic “b”
CDead-man
When a logic requiring a CLOSE (b, C), input is selected, the
OPEN B inputs will automatically be changed to CLOSE. , if you
choose a logic that does not require the use of CLOSE inputs,
these inputs will change to OPEN B.
For a description of how the logics operate, see the related paragraph.
E

BRAIN 17 20 732788 - Rev. A_1
ENGLISH
Display Basic Function Default
PA
PAUSE A and PAUSE B TIME (visualised only with Automatic logics)
Isthepausetime in aTOTAL opening andPARTIAL opening (it is enabledonly
if a logic with pause time has been selected).
Adjustable from 00 to 59 sec, in 1-second steps.
Next the value 59, the viewing changes to minutes and tenths of a second
(separated by a decimal point) and time is adjusted in 10-second steps up to
the maximum value of 9.5
minutes.
e.g.: if the display shows
2.5, the time is 2 min and 50 sec.
30
Mn
NR. OF MOTORS:
You can select the number of motors present in the system:
1= 1 motor
2= 2 motors
If the SETUP is performed with only one motor, and later two mo-
tors are used, the board will signal error 14 - configuration error,
which can be deleted by repeating the SETUP with two motors or
by returning to one motor.
If a SETUPis performed with two motors and later only one is used,
the board will not signal an error. Only the motor connected to input
M1 will move.
2
(swing-
leaf)