Genius GSM MOBILE STARTER User manual

USER MANUAL
GENIUS
GSM MOBILE STARTER
Main Features
Suitable for three phase and single phase
Auto Switch Mode ( Start automatically after power reset)
Pump On and OFF through SMS and Missed call
Dry Run/ Low level Protection
Phase Failure/ Phase Not available Protection
Timer Function
Single Phase mode and three phase mode
External Antenna for better signal

Wiring Diagram
Over Load
Relay
Cut
NC
RYB
DRY RUN
/ LOW LEVEL
GENIUS
GSM MOBILE STARTER
DRYRUN SENSOR
3ph
Motor
5
654
53
T3 96
95
X
B
13
24
A1 A2
T1 T2
RY
Contactor
NO
MCB
Coil
Stop NC Start NO
B
RY
3Phase input is Must
3 Phase Mode
Switch Position
1 Phase Mode
12V AC/DC
x
B
RY
3 Phase Mode
Switch Position
1 Phase Mode
12V AC/DC
x
Input 12V is Must
3phase mode switch position
1 phase mode switch position
Specification
Input current : 500mA,
Input voltage: For 3phase mode for 3ph-415V
For 1ph mode 12V AC/DC
Sim: Regular 2G sim, exept Jio

Quick start steps
1. Preparing Sim card - Ensure the Sim card is activated that you can send
sms , Add sms pack , Insert the sim card in sim card slot
2. Connect the antenna
3 Connect Input power supply (Switch position to be check)
- 3PHASE RYB for 3phase Mode (3phase mode)
- Connect adapter 12v/ 2 amps for 1ph mode (1ph mode)
4. Check Status LED to check Network is connected or not
1sec On / 1sec Off Blink - Network Not connected
Continues ON - Network Connected
5. Once the network is connected Then send SMS commands
How to Program the Gsm motor control and test !
1. Check Before sending sms , Netwrok is connected , Status Led
should be stable and continues ON
2. Then Store the Mobile No using command - send sms - C
3. To check status send SMS - 7 - status will be recived thru sms
4. To on the motor you can send SMS 1 for ON / 2 For OFF
5. Pump Control By calling -
To pump ON - Call to the sim No after 5 rings call will be disconnected
To Pump OFF- Call to the sim No after 3 rings Call will be disconnected

Commands Example Description Acknowledge
1STNXXXXXXXXXX 1STN9148152701 TO Store First No SMS to Stored Mobile No
2STNXXXXXXXXXX 2STN9591978178 TO Store SecondNo SMS to Stored Mobile No
Stores upto 5Nos
SMS To be send to the Mobile Starter number as below mentioned format
SPN SPN To check Store No SMS to stored No
DEL=X For Example to del No 2
DEL=2 To Delete Store mobile
No
Command by SMS
SMS Example
Description
2
3
4
5
6
7
1
2
3
4
5
6
7
1
Description
Pump On through SMS
Pump OFF through SMS
Auto Mode ON (Automatically ON pump after power Reset)
Auto Mode OFF (Pump Not ON after power Reset)
Mode-1 Pump mode- 3Phase mode
Mode-2 Pump mode- 1 Phase mode
To check Status
Command by Calling
If you call from Registered No , Call will be disconnected after 5 rings
First Missed call for Pump ON - After 5 rings will be disconnected
Second Missed call For Pump OFF - After 3 rings will be disconnected
Timer Function - To set for timer for Particular ON time
ONTIME =XX Example To set On motor for 30 minutes
Send SMS - ONTIME = 30 --- you can set upto 99 Minutes
@ Mode1 without 3 phase ok Motor will Not ON
Mode 2 - 3 phase will not check ( 3 phase sense Disabled)
@ Mains power ON message will be sent to Master No
@ Reply messages from all slave No will also sent to Master No
Manufactured by
Genius Technologies-Bengaluru-560061
Customer care: geniustfl@gmail.com, 080-4101 0132