GeoVision GV-3D People Counter V2 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
User’s Manual V1.01
GV-3D People Counter V2
3DPC2V101-A

© 2018 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
May, 2018

i
Contents
Contents................................................................................................................................ i
Firmware and Software Compatibility................................................................................ ii
Chapter 1 Introduction ..................................................................................................... 3
1.1 Packing List............................................................................................................. 4
1.2 Optional Accessories............................................................................................... 5
1.3 Overview ................................................................................................................. 6
1.3.1 Bottom View ............................................................................................. 6
1.3.2 Rear View................................................................................................. 7
Chapter 2 Getting Started................................................................................................. 8
2.1 Connecting the Device............................................................................................. 8
2.2 Restoring to Factory Default Settings ...................................................................... 9
2.3 Wall / Ceiling Mount................................................................................................10
Chapter 3 The Web Interface...........................................................................................12
3.1 Accessing the GV-Web Report Lite.........................................................................12
3.2 Setting the GV-3D People Counter V2....................................................................13
3.2.1 Live View.................................................................................................13
3.2.2 People Counter Settings..........................................................................14
3.2.3 Report to Other Servers...........................................................................16
3.2.4 General Settings......................................................................................17
3.3 Accessing People Counting Data............................................................................26
3.3.1 Device .....................................................................................................27
3.3.2 Group ......................................................................................................29
3.3.3 Log..........................................................................................................31
3.3.4 Query.......................................................................................................32
Chapter 4 Auxiliary Device Connectors.........................................................................35
PIN Assignment ..............................................................................................................35
Chapter 5 GV-IP Device Utility.........................................................................................36
Appendix.............................................................................................................................38
Optimal Installation..........................................................................................................38
Detection Limitations.......................................................................................................39

ii
Firmware and Software Compatibility
The compatible versions of GV-VMS and GV-Web Report are listed below:
Model
GV-VMS
GV-Web Report
GV-3D People Counter V2 V1.01
V16.10.3.0 or later
V2.2.6.0 or later
Note: For showing the people counting data on GV-VMS’s live view, see Video Analysis by
Camera in GV-VMS User’s Manual.

Introduction
3
1
Chapter 1 Introduction
The GV-3D People Counter V2 can count and analyze the number of people passing by the
designated area at high precision counting accuracy. With its Power over Ethernet and
user-friendly interface, the counter is simple to use and easy to install. You can look up neatly
compiled people counting data in chart analysis with the support of GV-Web Report Lite, its
built-in Web interface. In addition to its sleek and stylish design, the counter also supports the
I/O devices and GV-GPS Receiver for accessing people counting data remotely.
Figure 1-1

4
1.1Packing List
1. GV-3D People Counter V2
2. SDHC Micro SD card
3. Ceiling Mount Kit
4. Wall Mount Kit
5. Installation Sticker x 2 (Wall mount /
Ceiling mount)
6. Screw x 4
7. Anchor x 2
8. Download Guide
9. Warranty Card

Introduction
5
1
1.2Optional Accessories
Optional accessories can expand the capabilities of your device. Contact your dealer for more
information.
Options
Details
GV-GPS Receiver
Receive the GPS signals for 3D People Counter
positioning.
GV-Web Report
Through a Web browser, the GV-Web Report keeps track
of and analyzes the people counting results and shows
the latitude and longitude from up to 1000 units of GV-3D
People Counter V2.
GV-PA191
The GV-PA191 is a Power over Ethernet (PoE) adapter
designed to provide power to the IP device through a
single Ethernet cable.
GV-POE Switch
The GV-POE Switch is designed to provide power along
with network connection for IP devices. The GV-POE
Switch is available in various models with different
numbers and types of ports.

6
1.3Overview
This section illustrates the components of GV-3D People Counter V2.
1.3.1 Bottom View
1
Figure 1-2
No.
Name
Function
1.
Lens
Captures people’s image.

Introduction
7
1
1.3.2 Rear View
1 2 3 4
Figure 1-3
No.
Name
Function
1
Ethernet Port
A plug for PoE (IEEE 802.3af).
2
Default Button
Resets all configurations to factory default settings.
3
Terminal Block
The connectors for the sensor input, alarm output and GPS
receiver.
4
Memory Card Slot
Inserts a micro SD card (SD/SDHC/SDXC/UHS-I, Class 10) to
store recording data.

8
Chapter 2 Getting Started
2.1 Connecting the Device
12
Figure 2-1
1. Plug a standard network cable or PoE to provide power supply and Internet connection.
2. Insert a micro SD card.
Note: GV-3D People Counter V2 only supports PoE. You may purchase GV-PA191 PoE
adapter to connect to your router.

Getting Started
9
2
2.2Restoring to Factory Default Settings
If for any reason the device is not responding correctly, you can restore it to its factory default
settings.
Green LED Default Button
Figure 2-2
1. Press and hold the Default button on the rear panel.
2. Release the Default button when the green LED stops blinking. The device reboots
automatically after loading the default settings.
Note:
1. The power supply should remain constant throughout the process of loading default.
2. You can also reset the device using GV-IP Device Utility. See Chapter 5 GV-IP Device
Utility.

10
2.3Wall / Ceiling Mount
You can use the Wall / Ceiling Mount Kit to mount the device on a desired location.
Wall Mount
Ceiling Mount
1. Remove the device’s outer case.
Figure 2-3

Getting Started
11
2
2. Secure the desired mounting kit to the designated position with 2 screws.
Figure 2-4
3. Reassemble the outer case.
Figure 2-5
4. Put the installation sticker to the wall with the arrow pointing up.
5. Drill 2 holes according to the sticker and insert the 2 screw anchors to the 2 holes.
6. Secure the device to the wall with 2 long screws.
7. Optionally install the ground wire with the screw as shown below:
Ground Wire
Figure 2-6

12
Chapter 3 The Web Interface
Once the GV-3D People Counter V2 is connected to the network, you can view counting data
by using GV-Web Report Lite, a Web server built into the GV-3D People Counter V2. When
the device is connected to a network with a DHCP server, it will be automatically assigned
with a dynamic IP address. To look up this IP address, use GV-IP Device Utility desceribed in
Chapter 5 GV-IP Device Utility.
However, if you do not have a DHCP server on your network, access the device by its default
IP address 192.168.0.10.
3.1 Accessing the GV-Web Report Lite
To access the device, Microsoft Internet Explorer 10 or above is required.
Two types of users are allowed to log into the device: Administrator and Guest. The
Administrator has full access to all system configurations, while the Guest can only access the
Device, Group, Log and Query pages.
1. In your Web browser, type the IP address or the domain name of the device in the
Location / Address field. This page appears.
Figure 3-1
2. Select the Language.
3. Type the default ID and password admin.
4. Type the characters shown in the image and click Login.

The Web Interface
13
3
3.2 Setting the GV-3D People Counter V2
Once logging into the GV-Web Report Lite, click the Setup tab on the top bar. The Setup page
appears. Here, you can configure the people counting and / or the network settings of the
device. Click Reset to restore all configurations of this page to its factory default settings.
3.2.1 Live View
Figure 3-2
[Live View] Draw a box on the live view to mark the boundary of the detection zone. People
moving across the blue box toward the red arrow will be counted as Out whereas people
moving across the blue box toward the green arrow will be counted as In.
◼Live View: Click to see the black and white live image of the detection area captured by
the infrared sensor of the device.
◼REC: Record the live view for 30 seconds. Only one video can be stored in the SD card at
a time. The existing recording will be overwritten by the new recording.
◼Download Recorded File: You can download the recorded file and provide the recording
to the maintenance attendants for troubleshooting.

14
3.2.2 People Counter Settings
In this panel, you can modify people counter settings, set up Counting Area, and reverse the
direction of entrance on Live View.
Figure 3-3
◼Device Height: Type the height of the installed device. Depending on the height where
the device is installed, the range of detectable height for people varies.
◼Minimum People Height:Type the minimum height for a person to be detected.
◼Device and Objec Distance < 60 cm: Select this option when the distance of the installed
device and intented objects is lower than 60 cm. Once the option is selected, the detection
range will be reflected below.
◼Detail: Click the button to see an illustration of the detectable range and the dimensions of
the detection area based on the height you specified.
Figure 3-4

The Web Interface
15
3
◼Detected Sensitivity: Adjust the detection sensitivity at Low, Medium or High.
◼Detect Area: Apply or clear image masks on the live view. Select Mask Position to drag
image masks to conceal certain area on the live view. People moving across the defined
mask position will not make a count.
◼Counting Area: Enable to minimize repeated counting of people who lingers around the
detection zone. Once enabled, a mask appears on live view and people who lingers within
the difined counting area only make a single count.
Figure 3-5
◼Wrong Direction Alarm: Enable if the detection area is exit only or entrance only,
a wrong direction count will be recorded in GV-Web Report Lite under Counting Signage
when people are detected to be moving in the wrong direction. See 3.3.1 Device.
◼In/Out Direction Change: To reverse the direction of the In and Out arrows in the Live
View screen, click the Change button.
After configuring people counter settings, click the Save button.

16
3.2.3 Report to Other Servers
You can send people counting data to up to three other GV-Web Report Lite servers and / or
GV-Web Report for data collection and analysis. To query data collected by the GV-Web
Report Lite, see 3.3 Accessing People Counting Data.
1. Select Report to Server.
2. Type the IP address of the GV-Web Report Lite or GV-Web Report.
3. Modify the default Port 30003 if necessary.
4. Type the Name and the Password to access the GV-Web Report Lite or GV-Web
Report.
5. If you click Time Sync under one of the servers, the current device time will be
synchronized with the selected server. To cancel time synchronization, double-click
Time Sync.
Note: GV-3D People Counter V2 is only compatible with GV-Web Report V2.2.6.0 or later.

The Web Interface
17
3
3.2.4 General Settings
This panel below the Live View allows you to manage various settings, such as network,
device settings and more, from the following tabs: User, DDNS, SMTP, Export, SCH, IP, SD,
FW, Time, MEM, GPS, I/O, FTP and ALARM.
[User]
◼Machine Name: Modify the display name of the device.
◼Login Name / Password: Modify the login name and password for accessing the device.
The default login name and password are admin.
◼Port: Modify the port or keep the default value 30003. When connecting to other servers,
the device must use the same port as the servers.
◼Guest Account /Pw: Modidy the login name and password for accessing the device with
the guest account. The default login name and password are guest.
Figure 3-6

18
[DDNS]
DDNS (Dynamic Domain Name System) provides a convenient way of accessing the device
with a dynamic IP address. DDNS assigns a domain name to the device, so that the
Administrator does not need to check if the IP address assigned by DHCP Server or ISP (in
xDSL connection) has changed.
Figure 3-7
1. Click Register to register a GeoVision DDNS Server or apply for a host name from other
DDNS service provider’s website.
2. Type the Host Name used to connect to the device.
3. Type the Name and Password used to enable the service from the DDNS.
4. ClickConnect.
[SMTP]
You can send a report of counting results from a specified E-mail address. For this function to
work, make sure the mail server is properly configured, and the Enable Auto Export function
in the Export tab is enabled.
Figure 3-8