German pool PHS-200 User manual

P.1
USER MANUAL
Please read these instructions and warranty information carefully
before use and keep them handy for future reference.
PHS-200
Online Warranty Registration
Commercial Grade High-Speed
Food Processor

如欲獲取更多有關本產品最新資訊及食譜，歡迎瀏覽本公司網站。
For additional product information and cooking recipes, please visit our website.
www.germanpool.com
Please register your warranty information now !
For Warranty Terms & Conditions,
please refer to the last page of this user manual.
有關保用條款細則，請看本說明書最後一頁。
請即進行保用登記﹗

Table of Contents
Product Structure
Operating Instructions
05
07
Notice for Operation 11
Measuring Cup, Lid and Blade Mount 10
Care & Maintenance 12
Technical Specifications 12
Warranty Terms & Conditions 23
Notice Before Use 04
Please register your warranty information now !
For Warranty Terms & Conditions,
please refer to the last page of this user manual.
有關保用條款細則，請看本說明書最後一頁。
請即進行保用登記﹗

Notice Before Use
P.4
1. Before plugging in the appliance, check that the electrical rating shown on the rating plate corresponds with your
home electricity supply.
2.Neversubmergetheunitbaseoftheapplianceinwaterorotheruids,norrinseitunderthetap,toavoidriskofshort-
circuit or electric shock. If there is water inside the unit base, please contact German Pool or a licensed technician for
repair.
3. Never put the power cord or plug into water for cleaning. Do not wipe the plug prongs with damp cloth, nor plug in with
wet hands.
4. Plug the appliance to the wall outlet properly and securely. Loose plug may lead to overheating or electric shock.
5.Ifthepowercordisdamaged,itmustbereplacedbythemanufacturer,itsserviceagentsorqualiedelectriciansin
order to avoid a hazard.
6. Never leave the appliance unattended.
7. Keep hands and utensils out of the container while the motor is running to prevent the possibility of severe personal
injury and/or damage.
8. Do not run the appliance without loading in the blender jar.
9. To prevent spillage, do not put liquid in the blender jar exceeding the MAX line.
10. Do not expose the appliance to heat sources such as a radiator or sunlight. For good ventilation, do not place cloth
underneath the appliance.
11. The appliance is for indoor use only.
12. Always operate with the lid in place. When processing hot beverages, properly secure the lid and measuring cup in
place to avoid scalding due to spraying of hot liquids.
13. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or any individual lack of experience and knowledge, unless they have been given supervision or
instruction by a person responsible for their safety.
14. Children should be supervised to ensure that they do not play with the appliance.
15. Switch off the appliance and disconnect from supply before changing accessories or touching any rotating parts.
16. The blade is very sharp, use with caution when handling the blade, emptying the jar and during cleaning. Do not
attempt to disassemble the blade assembly and touch any rotating parts.
17. Unplug the power cord from the wall outlet when the appliance is not in use, before putting on or taking off parts,
and before cleaning.
18. If the motor has overheated, the temperature monitoring system will be triggered and the motor will stop.
Switch off the appliance and let the motor cool down. The motor temperature monitoring system will reset after the
food processor is unplugged from wall socket for 45 minutes.
19. Any servicing should be performed by an authorised service representative. Do not attempt to disassemble, repair
or modify the appliance.
Important
-Forsafetypurpose,youshouldreadtheinstructionscarefullybeforeusingtheapplianceforthersttime.Save
the instructions for future reference.
- The appliance is designed for domestic use and may only be installed and operated in accordance with this
instruction manual.
-Donotruntheappliancewithoutloading.Itisstrictlyforbiddentooperatethisappliancewithoutthepresenceof
anyliquids,solidsorsemi-solidsinsidetheblendingjar.

Product Structure
P.5
Unit Body
Measuring Cup
Seal Ring
Blender Jar
Blade Assembly
Blade Mount
Drive Coupling
Cushion Base
Safety Lock
Unit Base
Anti-SkidRubber
Power Cable
Lid
Blender Handle
Control Panel
Sound Enclosure
(PHS-CVR)

Product Structure
P.6
Control Panel
Preset Programmes
(Dough,Sauce,Vegetable)
On/Off Button Speed Setting
Buttons
Pulse Button
Preset Programmes
(Hot Drinks,Nuts,Smoothie)
Time Indicator

Operating Instructions
P.7
Important
-Donotruntheappliancewithoutloading.Itisstrictlyforbiddentooperatethisappliance
withoutthepresenceofanyliquids,solidsorsemi-solidsinsidetheblendingjar.
-Undernocircumstancesshouldtheblendingjarbesubmergedinanyliquids.Donot
spray or splash any liquids at the blending jar base. Do not directly rinse the blending jar
base under the tap. The blending jar is not suitable for the dishwasher. If the blending
jar base is sprayed or splashed wet, dry immediately.
-Undernocircumstancesshouldtheblendingtimeexceed1minutewhendry-grinding.It
is advised to lettheappliancerestfor5minutesbeforeresumingdry-grinding.
ON/OFF Button
1. Plug in the power, all the indicators light up for 0.5 sec, the buzzer beeps for 1 sec, then the unit turn to standby
mode directly. Red light on the ON/OFF buttonasheswithotherindicatorlightsoff.Press ,the red light
on the button stays lit, programme indicators on the control panel: and the digital
screen turn white and the display shows 00:00, speed control indicators
turn white. The unit is in standby mode at this moment (in standby mode, if the unit is left idle for 3 minute, it
willautomaticallyturntoenergy-savingmode,foreverytouchcontrol,thebuzzerbeepsfor0.5second).Inany
working mode, touch button, the unit will switch to standby mode.
2. User should choose the preset program and working speed , Press
the button, the unit will operate in corresponding preset program. In any working mode, press the button,
the unit stops working and switches to standby mode.
Speed Setting Buttons
Press any , then the indicators on the left side of the pressed buttonwilllightupandashfor30sec.pressthe
button in 30 sec, the indicator turns white and stays lit, the unit starts to work in the corresponding speed.
Indicators on the left side of the corresponding working speed turn white and stay lit, (For example: when the
unitworksatspeed8,indicatorsontheleftsideofspeed8lightup),otherspeedindicatorsstaysemi-bright,time
display counts from “00:01”. Press button when it’s time to stop. The unit stops working and turns to standby
mode; the maximum working time of the unit is 10 minutes, after 10 minutes, the unit stops working (the time
displays 10:00 and pause for 5 sec) and automatically goes to standby mode.
Pulse Button
Pulse button is a manual button. In standby mode or working mode, press andtheindicatorashesfor0.5
sec and pauses for 0.5 sec. The unit does not operate until long press on button in 30 sec. The unit starts to
work and time display counts from “00:01”. Loose the button, and the unit stops working, and time display stops
to keep timing. If the unit is idle for 5 sec, the unit will automatically turn to standby mode and the motor will work
in speed H. When the time display shows the maximum time of 10:00, the unit will automatically turn to standby
mode.
1 2 3 4 5 6 7 8 9 H
Watch the video clip

Operating Instructions
P.8
Preset Programmes
Instandbymode,pressanypresetprogrammeicon,thecorrespondingindicatorwillash(ashtime:30sec),pressthe
buttonin30sec,theunitwillworkinthecorrespondingpresetprogramme.Aftertheprogrammenishes,theunit
turns back to standby mode.
Icon Programme Descriptions
Dough
Sauce
Vegetable
Hot Drinks
Nuts
Smoothie
Continuously work at speed 1 for 2 min
(400gour+240gwater).
Speed H for 30 sec and pause for 2 sec; then speed 6 for 10
sec and pause for 2 sec; then speed H for 60 sec and pause
for2sec;nallyspeed6for10sec.
Total time is 1 min 56 sec. Soft booting for every operation.
Accelerate to speed 7 in 7 sec.
Then accelerate to speed H in 3 sec and
stayatthisspeeduntilnish.Totaltimeis8min.
Speed H for 8 sec and pause for 2 sec. Run in cycle until
nish.Totaltimeis30sec.Softbootingforeveryoperation.
Speed 8 for 2 sec and pause for 1 sec. Repeat the cycles 5 times.
Then speed H for 45 sec. Total time is 1 min.
Soft booting for every operation.
Speed 5 for 5 sec.
Then speed 8 for 2 sec and pause for 1 sec,
repeat 10 times. Total time is 35 sec.
Soft booting for every operation.

Notice for Operation
P.9
Operating Instructions
Step 1
Press the two sides of the detachable rim and push it
out to the backside.
Step 3
Placethecushionmatattoinstall.Thecushionmat
should be in the correct position by aligning the three
buckle parts.
Installation of Sound Enclosure
Step 2
Remove the detachable rim from the blender.
32
1

Notice for Operation
P.10
Operating Instructions
-Insert the measuring cup to the lid (align the two bumps on the measuring cup to the two grooves on the lid and
 turnanti-clockwisetoposition).Thenpressdownthelidoftheblenderjartoclose.Toopen,pullupbytheapofthelid.
-Thesealringisdetachablefromthelidforeasycleaning.Removesealringfromthelidafterusetothoroughlycleanthe
lid and rinse off food residue from seal ring.
Measuring Cup, Lid and Blade Mount
Step 4
Slightly open the two sides of the sound enclosure to install.
Make sure the cushion mat and the sound screen are being
locked in the right position.

Notice for Operation
P.11
-Theappliancewillnotstartoperationuntiltheblenderjarisplacedontotheunitbaseforsafetypurpose.
-Insertthemeasuringcuptothelid(alignthearrowonthecuptothesymbolonthelidandturnitto
position).Thenpressdownthelidtotheblenderjartoclose.Toopen,pullupbytheapofthelid.
- Duringoperation,closethelidtightlytoavoidinjuriesduetospillingorsplashingofhotliquids.
- Windexcesspowercordunderneaththeunitbasetopreventtherubberfootfromsteppingonthepowercord.
- Whenthefoodistoothickorthereistoolittleliquidinthejar,themotorwillbedraggedtoalowspeedorstop
to operate. Hence, when blending thick and sticky food, start blending from low to high speed. If it is still unable
to blend, disconnect the power and stir the food inside the jar using a rubber stirrer to drive out the air trapped
in food. Then close the lid and switch on the blender to continue the operation.
-Whenoverheatingissensed,thetemperaturemonitoringsystemwillbeactivatedandwouldstoptheoperation
of the motor. In this case, put the appliance in a place with good ventilation to cool down for 45 minutes. The
system will be reset and you may resume the operation of the appliance.
-Keephandsandutensilsoutofthejarwhilethemotorisrunningtopreventthepossibilityofseverepersonal
injury and/or damage.
- Whenmakinghotbeveragesorsoups(suchassoymilk,porridge,bisque,etc.),pleaseensurethelidissecured
tightlytothejartopreventitfromfalling.Pleasebeadvisedtostarttheoperationatlowspeedrstandthen
gradually increase the speed, or simply use the “Pulse” mode.
-Whenmakingsauces(eg.almondsauce,jamandsesamesauce),stufngandnuts,putinaround2to3cups
of ingredients. The amount should neither be too much or too little. Keep the blending time within 2 min to
prevent any burnt smell due to overheating. Too much ingredients may lead to overloading and overheating of
the motor. In this case, wait till the motor temperature drops before operating again.
- Pleaseputliquidandsoftfoodintothejarbeforeputtinginhardfoodoricecubes.
- Whentheoperationnishes,pleasewaituntilthebladeassemblycomestoacompletestopbeforetakingout
the blender jar.
- Ifyousmellaburntsmellfromtheblender,stopoperationimmediately.Itmaybecausedbytheabrasionof
the rubber cushion base if it is not properly assembled.
- Donotoperatecontinuouslyforover10minuteseachtime.

Care & Maintenance
P.12
-Powerplugmustbedisconnectedbeforecleaningandrepair.  
-Cleansurfaceoftheblenderjarwithsoftclothorsponge.Themeasuringcup
and the seal ring can be detached for cleaning.
-Theblenderjarcanberinsedwithwater.
-Thesealringisdetachablefromthelidforeasycleaning.
-Aftercleaning,puttheblenderjaronitssideorupsidedowntodry*. Do not
submerge the whole jar in water.
-Donotsubmergetheunitbaseorpowercordintowaterorotherliquids.Cleanthe
unit base with soft cloth.
Model No PHS-200
Voltage/Frequency 220-240V~50/60Hz
Rated Power 1200 W
Dimensions (H) 430 mm
(W) 245 mm
(D) 484 mm
TechnicalSpecications
-Specicationsaresubjecttochangewithoutpriornotice.
-IfthereisanyinconsistencyorambiguitybetweentheEnglishversionandtheChineseversion,
the Chinese version shall prevail.
-Refertowww.germanpool.comforthemostup-to-dateversionoftheUserManual.
*To dry the blender jar in upside down position, please remove the residual water with a dry cloth. Do not position it near
the sink or basin to avoid water spraying to the base of the jar. This may cause rusting of the bearing and thus affect the
performance of the blender.
A Friendly Reminder :
To effectively remove dirt on the jar and blades and help them last longer, do the following: add in water
and lemon, close the lid and then press “Pulse ” button 2 to 3 times. Replace liquid with clean water
and repeat the above step.
3 Easy Steps to Cleaning the Blender Jar
Caution: Do not submerge the blender jar into water
1.Add1-2slicesoflemoninto750mlwater.Select“Vegetable”Programme.
2. Pour out water. Repeat Step 1.
3.Pouroutwater,andwipeitdrywithacleancloth.Putthejarsidewaysandletitair-dry.
Watch the video clip

目錄
Care & Maintenance
操作說明 17
量杯，杯蓋，杯座 20
產品結構 15
使用注意事項 21
清潔與保養 22
技術規格 22
保用條款 23
注意事項 14

注意事項
重要說明
- 為安全起見，初次使用產品前請先細閱本說明書，並保存說明書，以便作參考之用。
- 本產品只供家居使用。請必須依照說明書內的指示安裝及操作。
- 嚴禁空轉：在果汁杯內未有任何固體、流質食物或液體之情況下，切勿啟動本機。
P.14
1. 在使用本產品前，確認產品所標明的使用電壓，是否於家用的接地插座電壓一致。
2. 請勿將機體座泡在水中或對機體座澆水，以免引起短路或觸電，機體座主體內如有浸水，請洽經
銷商或服務處。
3. 機體座的電源線和插頭不可用水或其他液體清洗或浸泡，插頭不可用濕布擦拭，手部潮濕時請勿
插、拔插頭，以免引起觸電。
4. 本機在使用時，電源插頭務必要插到底，不插到底易造成觸電或由於發熱引起火災；請勿使用殘
缺或鬆動的插座。
5. 請勿損傷電線及電源插頭；使用受損的電線易引起觸電，短路或火災；如電源線損壞或發生其他
故障，切勿自行拆卸本機，必須由製造廠商或其服務處或具有類似資格的專業人員更換和維修。
6. 本機在使用時，切勿無人看管。
7. 果汁杯在主體上時，切勿將手或任何用具，金屬，異物放入果汁杯中，以免傷到人或損毀攪拌部
份。
8. 切勿將本機在無水情況下進行空轉。
9. 使用本產品時，果汁杯中的水或其他液體不能超過杯子上的最大刻度線。
10. 請勿將本機靠近熱源，請勿在機器下方放置抹布，以免造成散熱不良。
11. 本產品只適用於室內使用，請勿置於室外使用。
12. 操作時一定要蓋緊杯蓋，裝上量杯，在製作熱飲時請務必蓋好杯蓋，並確定先使用低速運轉，以
免高速會噴出熱液體，造成傷害。
13. 本產品不預備給體能弱、反應遲鈍或有精神障礙的人(包括兒童)使用，除非在對其負有安全責任
的人員的指導或幫助下安全使用。
14. 兒童應該被監督，請勿讓兒童使用或觸摸本機，以保證他們不玩耍器具。
15. 先關掉電器電源，拔下電源插頭，然後才可更換配件或碰觸任何運轉的部份。
16. 產品刀片非常鋒利，清空果汁杯和清洗時請務必特別小心，勿自行拆除刀片，請勿觸碰任何在運
轉的部份。
17. 當不使用機器或拆除或裝設配件或清洗時，請先拔掉插頭。
18. 摩打如超過負荷時，摩打將自動停止運轉，此為摩打內的溫度偵測保護系統啟動，並非摩打故
障，使用者需拔掉插頭大約45分鐘後，摩打內的溫度偵測保護系統才能重定，此時便可重新使
用。
19. 本產品有任何問題請勿自行拆卸、修理、改造，以免造成自身傷害。請聯絡本公司或持牌之專業
技術人員。

操作面板產品結構
P.15
主機
操作面板
隔音罩
手柄
杯蓋
量杯
密封圈
果汁杯
刀片組件
杯座
帶動輪
防震墊
安全開關
機座
防滑腳墊
電源線
(PHS-CVR)

操作面板
P.16
操作面板
產品結構
速度設定鍵開始/停止鍵 間歇運轉鍵
智能快速
程式輕觸鍵
(麵糰、醬汁、蔬果)
智能快速
程式輕觸鍵
(熱飲、堅果、冰沙)
時間顯示屏

操作說明
P.17
開關鍵
1) 產品通電，所有燈都亮0.5秒，蜂鳴器響1秒後，直接進入省電模式， 閃爍紅燈，其它都不亮。
觸摸 一次後， 亮紅燈， 及顯示屏亮白燈顯示00：00，速度
亮白燈，此時產品為待機模式(待機模式下如3分鐘沒有任何
操作，自動進入省電模式，每次觸摸有效一次，蜂鳴器響0.5 秒)。在任意狀態下，觸摸 圖案，
產品進入待機模式。
2) 用戶需先選擇好相應的智能快速程式或速度設定 任意檔速，
觸摸 鍵後，產品才運轉相應的功能，在各種工作模式下，觸摸 鍵，產品停止工作，自動
進入待機模式。
速度設定鍵
觸摸檔位任意一個 ，此時被觸摸鍵 以左的燈光全亮閃爍，閃爍時間為30秒， 在30秒內再
觸摸 ， 長亮白燈，產品開始按相對應的檔位工作，相對應的 以左長亮白燈，(比如：產品
按8檔運行中，8檔以左的全亮白燈 )，其它速度鍵燈光半亮，顯示屏從“ 00:01 ”秒開始計時，
欲停止觸摸鍵 ，停止工作，產品進入待機模式；產品運行上限時間為10分鐘，超過10分鐘後，
產品停止工作，（顯示屏時間顯示：10：00，停留5秒鐘），產品自動停止進入待機模式。
間歇運轉鍵
鍵為間歇運轉鍵（手動點觸摸），在待機或工作模式下，觸摸 一次，燈光閃爍，間隔閃爍
0.5秒，停止0.5秒，產品不工作，30秒內再次長按 ，產品開始啟動，工作的同時，顯示器開始計
時從“00:01 ”秒開始，用戶鬆手後停止工作，顯示屏計時，停止後 5秒內無操作，產品自動轉換到待機
模式，摩打以 H檔工作。顯示屏最大顯示時間到10：00後 產品自動進入待機狀態。
重要說明
- 嚴禁空轉：在果汁杯內未有任何固體、流質食物或液體之情況下，切勿啟
動本機。
- 任何情況下，切勿把整個果汁杯浸入任何液體泡浸；禁止向杯底澆水，不
能直接沖洗果汁杯底部。果汁杯不適用於洗碗碟機。杯底濺濕後，請立即
擦拭乾淨。
- 任何情況下，乾磨食材時不能連續操作超過1分鐘。如需連續乾磨，建議讓
機件靜置5分鐘再重複操作。
1 2 3 4 5 6 7 8 9 H
觀看視頻操作

操作說明
P.18
智能快速程式
在待機狀態下，觸摸任意一個智能快速程式鍵，相對應的智能快速程式鍵燈閃爍(閃爍時間為30秒)，
在30秒內再觸摸 鍵後，產品就運轉相應的智能快速程式，工作完成後，自動返回到待機狀態。
圖示 程式 程式描述
麵糰
醬汁
蔬果
熱飲
堅果
冰沙
以1檔連續工作2分鐘（用400克麵粉+240克水）
以8檔啟動運轉2秒，接著停止1秒，
反復此動作5次，接著加速至H檔並運轉45秒，
共運行1分鐘，每次啟動都用軟啟動
H檔運轉30秒，停2秒；6檔運轉10秒，停2秒；
H檔運轉60秒，停2秒；6檔運轉10秒，結束，
共1分鐘56秒。每次啟動都用軟啟動
7秒內加速至7檔，3秒內加速至H檔，
並維持在此檔位；總運轉時間為8分鐘。
以5檔運轉5秒；
接著以8檔運轉2秒，停止1秒，反復此動作10次；共運行35秒。
每次啟動都用軟啟動
以軟啟動運轉8秒H檔位，
停止2秒，以此循環，共運行30秒
每次啟動都用軟啟動

使用注意事項
P.19
隔音罩安装
操作說明
步驟一
按壓機座可拆式邊框的兩端，並向後推離。
步驟二
將可拆式邊框從機座上拆出來。
步驟三
安裝矽膠墊以固定隔音罩。安裝時需把矽膠墊平放，
並對齊三個卡扣，以確保安裝到位。
32
1

使用注意事項
P.20
操作說明
步驟四
稍微打開隔音罩的兩邊，把隔音罩裝到機座上，並確保隔音罩
上的三個開孔均扣緊於矽膠墊的卡扣。
- 將量杯放入蓋中 (量杯上有兩個小凸點，將凸點對準杯蓋中心口的兩個小凹處，放入後反時針旋轉
即可)再將杯蓋上果汁口，往下按入即可。再要打開時，只需將杯蓋手柄處往上拉即可。
- 杯蓋密封圈為可拆卸部件，當清洗時可將密封圈取下單獨完後再套上杯蓋，方便徹底清除杯蓋與
密封圈上的食物殘渣。
量杯，杯蓋，杯座