Geutebruck G-Cam User manual

G-Cam EFD-4260 H.265 IR Micro Dome IP Camera Quick Guide
2
3
This guide is for quick installing and connecting the G-Cam / EFD-4260 H.265 IR Micro Dome IP Camera. For more
details, please refer to the User’s Manual.
Installation Notices
This camera must be installed by qualified personnel and the installation should conform to all local codes.
Do not replace batteries of the camera. Risk of explosion may occur if the battery is replaced by an incorrect type.
To use an external power supply, please contact the camera manufacturer to confirm that the power supply uses
the same power specifications as the camera. The power supply must comply with the LPS requirements.
Function cables (Outdoor)
No.
Connector
Pin
Definition
Remarks
1
RJ-45
-
Network and PoE connections
2
Power Jack (DC 12V)
1
DC 12V
Power connection
2
GND
3
Audio I/O
Pink
Audio In (Line In)
Two-way audio transmission
Green
Audio Out (Line Out)
4
Alarm I/O
(4-Pin Terminal Block)
1
Alarm In –
Alarm connection
#Do NOT connect external power supply to
the alarm I/O connector of the IP camera.
2
Alarm In +
3
Alarm Out –
4
Alarm Out +
5
BNC
-
Analog video output
1
Default Button
-
Please refer to Default Button in the table under Camera’s Connectors.
2
microSD Card Slot
-
Please refer to microSD Card Slot in the table under Camera’s
Connectors.
NOTE: To avoid audio quality degradation, do NOT connect built-in microphone and external audio-input
device (via Line In) at the same time. The same is valid for Audio out.
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.
Camera Cabling
Power Connection
Use a DC 12V power adaptor and plug it to the camera and the power outlet. Alternatively, users can use an Ethernet
cable and connect it to the RJ-45 connector of the camera and a PoE switch.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
NOTE: Check the status of both power and network activity indicator LEDs. If either LED is unlit, please check
the corresponding connection.
Green Power LED lights up when the camera is powered up.
Orange Network LED (1) flashes when data is being transmitted over network,
(2) lights up for good network connection.
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and plug-ins or
setting Internet’s security level to default. For further details, please refer to the User’s Manual.
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet> and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins” items to
<Prompt> or <Enable>.
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>.
Step 4: Down the page, click <Default Level> and click
on <OK> to confirm the setting. Close the
browser window and open a new one later for
accessing the IP camera.
Camera Login
The default setting of the camera is: DHCP. If no DHCP server is in network, the camera sets itself to 192.168.0.250.
To access the camera in this case, please set the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID and Password
Key in the camera’s IP address in the URL bar of the web browser window and hit on “Enter”.
Enter the default username (root) and password (admin) in the prompt request dialogue. Note that username is
case sensitive.

4
Install the ActiveX Control
After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
Right click on the information bar, and then click on <Install ActiveX Control…> to permit ActiveX control installation.
In the pop-up security warning window, click on <Install> to start downloading DCViewer software on the PC.
Click on <Finish> after DCViewer installation is completed.
Browser-based Viewer
The main page of the IP camera user interface is shown as the figure below. Please note that function buttons will
vary depending on the camera model. For details see in the Webbrowser Manual.
NOTE: For details about configuring the camera in GEUTEBRÜCK-Software (G-Set and GSC-Setup),
please refer to the Quick Guides, which can be found on the supplied CD ROM.
G-Cam / EFD-4260
H.265 IR Micro Dome IP Camera
Quick Guide
Ver. 1.0