GEZE GC 363 R User manual

GC363 R / SF
151263-01
42.8438 v1 - 01-2015

GC 363 R / SF
2
Contents
Symbols and illustrations.................................................................................3
Abbreviations.......................................................................................................3
Product liability....................................................................................................3
1 Safety ..........................................................................................................3
1.1 Intended use........................................................................................................................3
1.2 Safety notices .....................................................................................................................4
1.3 Safety conscious working...............................................................................................5
1.4 Environmentally conscious working...........................................................................5
2 Description ...............................................................................................5
2.1 Supplied by GEZE...............................................................................................................7
3 Work to be done before installation................................................8
3.1 Installing the drive.............................................................................................................8
3.2 Protection sensor...............................................................................................................9
4 Installation ............................................................................................. 10
4.1 Installation without accessories ................................................................................10
4.2 Installation with ceiling installation set..................................................................11
4.3 Installation with mounting bracket..........................................................................13
4.4 Installation with weather canopy ............................................................................. 14
4.5 Cabling................................................................................................................................15
5 Commissioning .................................................................................... 16
5.1 Radar detector .................................................................................................................16
5.2 Protection area.................................................................................................................18
5.3 Settings...............................................................................................................................19
5.4 Teaching.............................................................................................................................20
6 Conguration possibilities............................................................... 20
6.1 Using the LCD menu......................................................................................................20
6.1.1 Display during normal function ................................................................................20
6.1.2 Menu navigation.............................................................................................................20
6.1.3 Changing ZIP code......................................................................................................... 21
6.1.4 Changing and storing values......................................................................................21
6.1.5 Checking values using the remote control............................................................21
7 Settings ................................................................................................... 21
7.1 Default settings ...............................................................................................................21
8 Last installation steps......................................................................... 25
9 Further installation situations......................................................... 26
9.1 Single leaf installation................................................................................................... 26
9.2 Lintel installation.............................................................................................................27
10 Maintenance ......................................................................................... 28
Original operating instructions for device version 0400

3
SafetyGC 363 R / SF
Symbols and illustrations
Warning notices
Warning notices are used in these instructions to warn you of property
damage and personal injury.
XAlways read and observe these warning notices.
XObserve all the measures that are marked with the warning symbol and
warning word .
Abbreviations
FR Escape and rescue routes
IR Infrared
AIR Active infrared control
RAD Radar
LCD Liquid Crystal Display
HSK Main closing edge
NSK Secondary closing edge
Product liability
In accordance with the liability of the manufacturer for his products as
dened in the German "Product Liability Act", the information contained
in this brochure (product information and proper use, misuse, product
performance, product maintenance, obligations to provide information and
instructions) is to be observed. Failure to comply releases the manufacturer
from his statutory liability.
1 Safety
1.1 Intended use
The combined sensor GC 363 may only be used to actuate and safeguard
automatic sliding doors and circular sliding doors with GEZE drives. The
minimum object size corresponds to the reference object CA according to
DIN 18650 or 16005 both upright and lying down. The sensor can be used to
secure automatic sliding doors against impact and trapping of the human
body.
11 Error messages and troubleshooting........................................... 28
12 Technical data....................................................................................... 31
13 Accessories / Spare parts .................................................................. 33

Safety GC 363 R / SF
4
GC363 R (in the direction of
emergency exit)
GC363 SF
1.2 Safety notices
àThe mandatory installation, maintenance and repair work must be per-
formed by properly trained personnel authorised by GEZE. Any attempts
at repairs by unauthorised personnel cancel the factory guarantee.
àThe device may only be operated with safety extra-low voltage (SELV)
with electrically protective separation.
àThe country-specic laws and regulations are to be observed during
safety-related tests.
àMake sure that the door control cover is tted correctly and earthed.
àIf unauthorised changes are made to the system, GEZE cannot be held
liable in any way whatsoever for any resulting damage, and the approval
for use in escape and rescue routes ceases.
àGEZE makes no guarantee for combinations with third-party products.
àOnly original GEZE parts may be used for repair and maintenance work.
àObserve the latest versions of directives, standards and country-specic
regulations, in particular:
àASR A1.7 "Doors and gates"
àDIN 18650 "Building hardware – Automatic door systems"
àDIN EN 16005 "Power operated pedestrian doorsets – Safety in use –
Requirements and test methods"
àAccident-prevention regulations, especially BGV A1 "General regula-
tions" and BGV A2 "Electrical systems and equipment".
àThe risk assessment and installation of the sensor and the door system in
compliance with national and international regulations and door safety
standards are the responsibility of the door manufacturer.
àAny uses of the device other than those described in this manual do not
correspond to the approved purpose and cannot be guaranteed by the
manufacturer.

5
DescriptionGC 363 R / SF
1.3 Safety conscious working
àSecure workplace against unauthorised entry.
àWatch swivelling range of long system parts.
àSecure the cover/drive panels against falling.
àAttach safety stickers to glass door leaves.
àDanger of injury with opened drive. Hair, clothing, cables, etc. can be
drawn in by rotating parts.
àDanger of injury caused by unsecured crushing, impact, drawing-in or
shearing spots.
àDanger of injury due to broken glass.
àDanger of injury due to sharp edges in the drive.
àDanger of injury during installation through freely moving parts.
1.4 Environmentally conscious working
àWhen disposing of the door system, separate the dierent materials and
have them recycled.
2 Description
The combined detectors GC 363 R / SF have a radar eld for detecting
movement and an infrared eld for protection.
It is not possible for several systems to inuence each other and result in a
hazard. Unintentional stop signals are possible where detectors are mount-
ed next to one another as their infrared measuring ranges overlap and each
sensor could activate the other. This inuence is kept to a minimum by
dierent frequency settings.
The optional interface GC 363 S is exclusively for use with the GC 363 SF
combined detector. The interface permits several combined detectors to be
switched in series for FR sliding doors with large opening widths.
Variant GC363 R GC363 SF
Black 151237 151239
According to RAL 151238 151240

Description GC 363 R / SF
6
1 Cover
2 GC363 S interface (optional
accessory for GC363 SF)
3 Setting button (grey)
4 Button for setting the angle of
the AIR curtain (red)
5 AIR lens (transmitter)
6 AIR lens (receiver)
7 Radar antenna (wide eld)
8 Radar antenna (narrow eld)
9 Width adjustment of the AIR
curtain
10 LCD
11 Main connector

7
DescriptionGC 363 R / SF
2.1 Supplied by GEZE

Work to be done before installation GC 363 R / SF
8
3 Work to be done before installation
3.1 Installing the drive
XMake sure that the drive cover is earthed.

9
Work to be done before installationGC 363 R / SF
3.2 Protection sensor
One combined detector per passage direction is installed on automatic
sliding doors. The protection sensor GC 339 may be required in addition for
larger opening widths.
XSee installation instructions GC 339.
For escape and rescue routes:
àuse protective door leaf if necessary. Heed standards.
GC 363 R
GC 363 R
GC 339
GC 339
GC 363 R
GC 363 SF

Installation GC 363 R / SF
10
4 Installation
4.1 Installation without accessories
XAvoid extreme vibrations.
XDo not cover the sensor.
XKeep away from uorescent lamps.
XKeep away from moving objects.
XAvoid highly reective objects in the infrared range.
max. 50 mm
GC 362
8 mm
DIN 7981 8 × ½“
1
2

11
InstallationGC 363 R / SF
4.2 Installation with ceiling installation set
68 × 293 mm
1
2
3
DOOR SIDE
DOOR SIDE

Installation GC 363 R / SF
12
1
click
34
4
1
click
5
click
6

13
InstallationGC 363 R / SF
4.3 Installation with mounting bracket
DIN 7981 8 × ½“
1
1
3
2

Installation GC 363 R / SF
14
4.4 Installation with weather canopy
1
2
2
3
4

15
InstallationGC 363 R / SF
4.5 Cabling
XHeed wiring diagrams for the sliding door drives.
1
3
1
GC363 R
GC363 SF
GC 363 SF +
The optional interface GC 363 S is exclusively for use with the GC 363 SF
combined detector. The interface permits several combined detectors to
be switched in series for FR sliding doors with large opening widths.

Commissioning GC 363 R / SF
16
5 Commissioning
5.1 Radar detector
XSet the detection eld and sensitivity of the radar movement detector as
per AutSchR:
àScanned eld = opening width x 1.5 m
àMovement speed from 10 cm/s must be detected
àThe whole door width must be covered for escape and rescue
route doors
0
0
1
11
2
2
2
3
30°
45°
15° 0
0
1
11
2-15°
+15°
0°
2
2
33
3
2.2 m 2.2 m
15°…45° –15°…15°
0
0
1
11
2
2
2
33
3
0
0
1
11
2
2
2
33
3
2.2 m 2.2 m
4m x 2m 2m x 2,5m
2.5 m

17
CommissioningGC 363 R / SF
Replacing radar antennas (narrow and wide)
3
4
5
6
1

Commissioning GC 363 R / SF
18
5.2 Protection area
The position of the IR curtain in relation to the door can be checked using
an infrared detector.
XActivate 4 visible
spots.*
XAdapt the angle of the AIR
curtain.
Yellow LED is ashing
on infrared detec-
tor : Alignment
correct.
2x
max. 9 cm
max. 20 cm
* Visibility depends on the environmental conditions.

19
CommissioningGC 363 R / SF
XTesting the emission
area.
àThe whole width of the door must be covered.
àTest the width of the required area using a piece of paper (DIN A4), since
the infrared detector scans the whole emission area.
Standard-conform sensor setting according to DIN 18650 / EN 16005
Installation height Scanned width DIN18650 / EN 16005
2.00 m
2.20 m
2.50 m
3.00 m
3.50 m
2.00 m
2.20 m
2.50 m
2.50 m / 3.00 m
2.50 m / 3.00 m
5.3 Settings
XCongure the sensor using LCD or remote control (see chapters 6 and 7).

Conguration possibilities GC 363 R / SF
20
5.4 Teaching
XBefore starting teaching, move out of the infrared eld.
XBefore leaving the installation, test the correct sensor installation.
Teaching 2 sec.
Teaching with door movement +4 sec.
0
6 Conguration possibilities
6.1 Using the LCD menu
6.1.1 Display during normal function
Opening impulse Protection Image shown negative
= active exit
Set contrast
6.1.2 Menu navigation
Passwort
XXXX
English
Deutsch
Français Zurück
Weiter
Zurück
Weiter
Voreinst.
XEnter
password,
if set