GFW KENDAL 4+3 DRAWER CHEST User manual

V1 2023.04
Page 1 of 24
Tools Required Person Required
1.5 Hourx 2
Approximate
Assembly Time
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and ttings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
KENDAL 4+3 DRAWER CHEST
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the KENDAL 4+3 DRAWER CHEST.
Please read the instructions carefully to ensure safe operation of the product.
Size : 1125 x 389 x 762mm

V1 2023.04
Page 2 of 24
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
● Due to the size of this product we recommend that it is assembled in the room intended for use.
● When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly.
● Unwrap all packaging materials and place the components on top of the carton box or on a clean oor to
prevent it from scratching.
● Check the pack and make sure you have all the parts listed.
● Ensure that this product is fully assembled as illustrated before use.
● Check all screws or bolts are tightened and inspect regularly.
● This product should only be used on rm, level ground.
● Keep small parts out of reach of children.
● Make sure the legs remain in contact with the ground.
● Tools not included.
WARNINGS
● DO NOT use power tools to construct this product.
● DO NOT tighten screws until fully assembled.
● DO NOT over tighten screws or bolts.
● DO NOT use this product if parts are missing, damaged or worn.
● DO NOT sit or stand on the product.
● It is essential that this unit is xed to the wall with the brackets provided for safety reasons. NB wall xings are
not included. Please source suitable xings for your wall type. If in doubt please consult a qualied
tradeperson.
● WARNING: Always ensure the area to be drilled is free from hidden electrical wires, water or gas pipes.
CARE INFORMATION
● Never use scourers, abrasives or chemical cleaners.
● To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

V1 2023.04
Page 3 of 24
SPECIAL TIPS FOR FITTING DRAWER
3
DRAWER BOTTOM
DRAWER FRONT
DRAWER RUNNER - B
FRONT
THIRD HOLE OUTER LAST THIRD HOLE
BACK
ROLLER
1
DRAWER FRONT
2
● Fix the second
screw on the last
third hole.
● Fix the rst screw
on the third hole
from front.
● Push the runner to
drawer front.
● Ensure the position of the
drawer runner is correct
as showed above.
DRAWER ROLLER
CABINET ROLLER
21 3
INSTALL DRAWER TO CABINET
● Locate both roller on
drawer box and roller
on cabinet.
● Align the roller on
drawer box on top of the
roller on cabinet.
● Push inside the
drawer box.
● Ensure the roller is in
the track of drawer
slide before push to
the end.
DRAWER RUNNER - A
FRONT
SECOND HOLE
TOP
BACK
TOP
FRONT
BOTTOM
BACK
1st
2nd
TOP
BOTTOM
1
TOP
2
● Fix the rst screw on the
second hole on drawer
runner as shown.
● Fix the second screw
following the holes on panel.
● Ensure the position of the drawer
runner is correct as showed
above.

V1 2023.04
Page 4 of 24
Parts
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The ttings pack contains small items that should be kept away from
small children.
CODE PART NAME QTY DIMENSION
ASide Panel - L 115 x 351 x 727mm
BSide Panel - R 115 x 351 x 727mm
CTop Panel 130 x 386 x 1125mm
DFront Bar 115 x 75 x 1055mm
ECentre Panel 115 x 336 x 513mm
FVertical Panel 215 x 196 x 351mm
GBottom Bar 115 x 75 x 1055mm
HBack Bar 115 x 75 x 1055mm
ISupport Bar 218 x 65 x 1055mm
J Front Prole 1 15 x 96 x 1116mm
K Small Drawer Front - L 1 15 x 205 x 358mm
CODE PART NAME QTY DIMENSION
LSmall Drawer Front - R 115 x 205 x 358mm
MSmall Drawer Front Centre 115 x 205 x 358mm
NDrawer Front - L 215 x 205 x 538mm
ODrawer Front - R 215 x 205 x 538mm
PDrawer Side - L 715 x 140 x 330mm
QDrawer Side - R 715 x 140 x 330mm
RDrawer Back 415 x 140 x 465mm
SDrawer Back - Small 315 x 140 x 286mm
Drawer Bottom 43 x 324 x 478mm
Drawer Bottom -Small 33 x 296 x 324mm
Back Panel 23 x 350 x 1081mm
BACK
PANEL
BACK
PANEL
DRAWER
BOTTOM
DRAWER
BOTTOM
SMALL

V1 2023.04
Page 5 of 24
Fixings (to scale)
5 cm
4 cm
3 cm
2 cm
1 cm
0 cm
2 cm
1 cm
0 cm
32x
M3.5 x 15mm
G
CSK Screw
36x
EU 24
C
Minix Bolt
51x
Dia. 8 x 30mm
D
Wooden Dowel
28x
M4 x 38mm
B
CSK Screw
28x
M6 x 8mm
H
Euro Screw
14x
#6 x 16mm
F
Tapping
Screw
7x
M6.3 x 50mm
A
Unitar Screw
2x
#10 x 16mm
E
Tapping
Screw
20x
I
Nail Pin
6x
J
Nail Leg
36x
Dia. 15 x 12mm
K
Minix Cam
7x
H-64mm
L
Handle
1x
M4
Q
Allen Key
7 set x
12" (300mm)
O
Drawer Slide
7 set x
12" (300mm)
P
Drawer Slide
2x
D-16mm
M
Flat Washer
2x
1.2x15x32x75mm
N
L-Mounting
Bracket
Fixings (not to scale)

V1 2023.04
Page 6 of 24
Layout Parts on Soft Surface
BACK
PANEL
BACK
PANEL
DRAWER
BOTTOM
SMALL
DRAWER
BOTTOM
SMALL
DRAWER
BOTTOM
SMALL
DRAWER
BOTTOM
x2
DRAWER
BOTTOM
x2
x2
x2
x2
x2 x2
x2
x2 x2

V1 2023.04
Page 7 of 24
STEP 1
STEP 2
HO
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
FRONT
TOP
BACK
12 x3 x
BACK
FRONT
BACK
FRONT
C
10 x

V1 2023.04
Page 8 of 24
STEP 3
STEP 4
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
FRONT
TOP
BACK
HO
2 x 8 x
BACK
FRONT
BACK
FRONT
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
FRONT
TOP
BACK
HO
2 x 8 x
(2x)
BACK
FRONT

V1 2023.04
Page 9 of 24
STEP 5
STEP 6
A
3 x
D
5 x

V1 2023.04
Page 10 of 24
STEP 7
STEP 8
K
5 x
D
5 x