GFW POLAR HIGH GLOSS LED TV UNIT User manual

Size:
Colour:
Finish:
76 x 45 x 80 cm (WDH)
White or Grey
High Gloss
Version 1 - 200707
PO No：
Page 1of 16
POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Polar 2 Door Sideboard.
Please read the instructions carefully to ensure safe operation of this product
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking.
1 Hr
Set Up
Tools Required

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
IMPORTANT -READ CAREFULLY -RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
CARE INFORMATION
To clean, wipe with a damp cloth.
Never use scourers, abrasives or chemical cleaners.
Do not use solvent based cleaners or detergents as they can bleach or damage the product.
Version 1 - 200707
Page 2of 16
This product is designed to hold 20Kg in total, spread evenly over the whole unit.
Do not exceed this weight.
We recommend that this unit is assembled in the room intended for use.
When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent them from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly
Tools not included unless specified in parts list.
WARNINGS
DO NOT
DO NOT
DO NOT
DO NOT
use power tools to construct this product.
tighten screws until parts are assembled or as advised in this guide.
over tighten screws or bolts.
use this product if parts are missing, damaged or worn.
For safety,this unit is designed to fix to the wall using the anti-tilt bracket (O).
INSTALLATION WARNINGS:
In order to prevent the cabinet tipping over, this product must be installed with the metal
anti-tilt bracket provided (O).
This is essential for the safety of you and your children, the cabinet is not free-standing.
Carefully assess the suitability of the wall to ensure that the fastening device will
withstand the load and forces generated.
Walls can be quite different in construction so only fixings for a standard block wall are
supplied - otherwise please choose the most suitable fixing for your wall type - if in doubt
consult an expert.
When drilling the wall always be sure the area to be drilled is free from hidden electrical
wiring, water or gas pipes.
The fixing of this product to the wall must be done carefully following the detailed stages
in this Assembly Instruction. See Steps 11 and 12.

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 3of 16
Parts and Fittings Checklist
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer.
The fittings pack contains small items that should be kept away from children.
6
7
4
1
3
2
7
8
8
9
9
10
11
12
13 5

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
All parts are packed in two carton
Size: 760 x 450 x 35 mm
Carton No: 2/2
Description:
Qty: 1
Carton No: 2/2
4
Qty: 1
Size:760 x 450 x 35 mm
1 2 3
Description:
Floating Top Panel Description: Base Panel
Qty: 1
Size: 067 x 450 x 15 mm
Carton No: 2/2
Description: LH Side Panel
Qty: 1
Size: 550 x 449 x 35 mm
Carton No: 1/2
Size: 360 x 50 x 15 mm
Carton No: 1/2
Description:
Qty: 2
10
7 8 9
Description: Front/Rear Plinth
Qty: 2
Size:630 x 50 x 15 mm
No: 2/2
Description: Back Panel
Qty: 2
Size: 955 x 298 x 3 mm
Carton No: 1/2
Description: rooDHL
Qty: 1
Size: 522 x 340 x 15 mm
Carton No: 1/2
Side Plinth
Under Top Panel
Size: 550 x 449 x 35 mm
Carton No: 1/2
Description:
Qty: 1
5 6
Description: Fascia Rail
Qty: 1
Size: 688 x 40 x 15 mm
Carton No: 2/2
RH Side Panel
11
Description: elbatsujdA Shelf
Qty: 1
Size: 687 x 395 x 51 mm
Carton No: 2/2
Version 1 - 200707
Page 4of 16
13
Description:
Qty: 1
Size: 550 x 116 x 15 mm
Carton No: 1/2
12
Description:
Qty: 1
Size: 225 x 043 x 51 mm
Carton No: 1/2
RH Door
Back Connect Rail

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 5of 16
2
S
Screw for Fixing Fascia
Rail to Top Panel
Screw for Fitting Hinges
and Hinge plates.
3.5x12mm
20A
20B
8C
T 24
4U
Item QuantityCode
Cam Lock
Dowel 8x30mm
Cam Bolt
Fittings (to scale)
10 20 30 40 50 60 70 80
(38mm overall)
Carcass Screw for
Fitting Side Panels to Base
Panel M7x50mm
QuantityCode Item
1
LED Clip
1
HBattery Box with
25cm LED Strip
3G Screw for
LED/Cable Clips
J
K 1
1
Fittings (packed in each LED pack).
Cable Clip
R
Battery Box 2
Sided Sticky Pad
4D M6 Nut
4
ESpring Washer
For M6 Bolt
Flat Washer
For M6 Bolt 4F
1I
Screw for Fixing Anti-tilt
Metal Bracket to Underside
of Under Top Panel
4x12mm
4x40mm

Version 1 - 200707
Page 6of 16
B
Tighten
FLUSH
CARCASS SCREW
General Hints & Tips
A28mm
A
A
Stop when
level
POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Fittings (not to scale)
QuantityCode Item
4
1
Q
M
N
P
4
8
M6 Box Spanner
Metal Tubular
Support
Cover Cap for
Tubular Support
Short M6 Double
Ended Bolt
Hinge & Hinge
Mounting Plate 4
1
Allen Key (4mm)
V
W
4X Shelf Support
1O Metal Anti-tilt Bracket
for Fixing Cabinet to Wall
Z 1Door Stopper

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 7of 16
Fittings required
Fittings required
For this step:
Tools required
STEP 1
STEP 2
For this step:
Tools required
J x1
H x1
K x1
R x1
G x3
K
H
G
G
J
Qx4
Place top (1) face down on a clean blanket or non-scratch surface
Screw in the 4 rods (Q) until they stop - do not overtighten.
R
G
Q x4
N x4
P x8
Q
Px4
Px4
Nx4
1

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 8of 16
Fittings required
Fittings required
For this step:
Tools required
STEP 3
STEP 4
For this step:
Tools required
Ax2
4
5
F x4
M
D x4
E x4
E
F
M
D
2
3
Ax6
A x10
C x8
Cx4
A
A
Cx4

B x2
POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
O x1
I x1
5
4
i.
ii. iii.
6
Version 1 - 200707
Page 9of 16
Fittings required
Fittings required
For this step:
Tools required
STEP 5
STEP 6
For this step:
Tools required
S x2
B x4
Be Careful when moving this
sub-assembly into position.
Assemble as close as you
can to Top Panel (1&2)
CAREFULLY PLACE (4) & (5) EVENLY IN POSITION
Sx2
Bx4
B
B
I
O

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
B x8
Version 1 - 200707
Page 10 of 16
Fittings required
For this step:
Tools required
STEP 7
STEP 8
For this step:
Tools required
9
9
13
WU
B x2
Fit Base Panel using x4 Carcass Screws (U) then fix x6 Cam Bolts (A)
Fittings required
3
Ux4
Ax6
Bx2
Bx2
A x6
U x4
W

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Fittings required
A x4
Version 1 - 200707
Page 11 of 16
For this step:
Tools required
STEP 9
STEP 10
For this step:
Tools required
7x2
7
7
8
8
Ax2
Fittings required
B x6
Bx2
Bx2
B x4
Bx6

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
For this step:
Tools required
STEP 11
STEP 12
Fittings required
For this step:
Tools required
Fittings required
Version 1 - 200707
Page 12 of 16
II.
III.
Carefully drill holes
in the wall.
I.
In the final position the cabinet is to be
used, place it flat against the wall.
From underside of the top carefully mark
the wall with a sharp pencil, dead-centre
of the holes in the short legs of the metal
Anti-tilt Bracket.
Warning:
Always ensure the area to be drilled is
free from hidden electrical wires,
water and gas pipes.
I
O
Hold cabinet firmly against the
wall. If necessary, loosen screw
(I) a little and push each metal
bracket (O) until touching the wall.
Screw into your wall fixings
making sure brackets are firm,
finally re-tighten screws (I).
Choose a suitable
screw for your wall
fixing method.
Choose a suitable
wall fixing method.

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 13 of 16
Fittings required
Fittings required
For this step:
Tools required
STEP 13
STEP 14
For this step:
Tools required
11
X x4
T x8
V x4
10
V
Tx2
12
Xx4
X

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 14 of 16
Fittings required
For this step:
Tools required
STEP 15
T x8
10
12
Initially, fix 4 screws (T) through
the centre of the elongated holes
in both hinge plates, screwing
into the side panel.
If it is necessary to re-align the door vertically,
loosen the screws (X) and adjust the hinge plates
up or down (Y) until gaps at top and bottom of
the door are even, then re-tighten the screws.
XY

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
Version 1 - 200707
Page 15 of 16
STEP 16
ii
i
iii iv
CHANGING THE BATTERIES
SLIDE OFF THE LID CHANGE BATTERIES
SLIDE LID BACK ON
USE GOOD QUALITY AA BATTERIES. FOR BEST RESULTS USE RE-CHARGEABLES.
T x8
Z x1
Once all the adjustments are complete and door is aligned, fix remaining 8 screws
(T) into the other hinge plate holes then check all the other hinge screws are tight.
Please do not over-tighten.
Z

POLAR HIGH GLOSS LED 2 DOOR SIDEBOARD ASSEMBLY INSTRUCTIONS
Version 1 - 200707
Page 16 of 16
Assembly Completed
Your Polar 2 Door Sideboard is now completely assembled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference