Gigabyte GH-PDU22-SC User manual

GH-PDU22-SC
REV.1002
Intel®Pentium®4 LGA775 / mPGA478 / AMD AM2 (940) /
K8(939/754)
Installation Guide
051227

- 2 -
GH-PDU22-SC
English
Table of Content
Checklist...............................................................................................................3
Specification.........................................................................................................4
Feature................................................................................................................4
Warranty Item.......................................................................................................5
Precautions..........................................................................................................5
Installation Instructions for P4 LGA775RM & Cooler.............................................6
Installation Instructions for Intel®Pentium®4 mPGA478 Clips................................7
Installation Instructions for AMD AM2 (940) / K8 (939 / 754) Clip...........................8
Installation of the Fan Speed Control Cable........................................................ 9

- 3 - GH-PDU22-SC
English
Checklist
(1)GH-PDU22-SC Cooler
(3) P4 clips
( mPGA478 /
LGA 7 75 )
(2)LGA775 RM
(8)GH-PDU22-SC
user's manual
(5) Heat sink paste
(4) AM2 / K8 clip (6) Screw (7)Fan Speed
ControlCable

- 4 -
GH-PDU22-SC
English
yFan Dimension : 110x110 x 25mm
yHeat Sink Dimension : 110x110 x 109mm
yHeatpipe Number : 3
yFan Speed : 2,450 rpm (default) / 2,000 rpm (low speed)
yRated Voltage : 12V
yNoise :23.1 dBA at 2,000 rpm(with fan speed cable)
27.5 dBA at 2,450 rpm (default)
yBearing Type: EVR Sleeve
yUniversal design fits all mainstream platforms
yOmni-directional cooler design with new advanced sintered powder wicks
yQuad-Way Airflow Design - Fully compliant with MOSFET thermal functions
ySolid pure copper base with nickel-plating finish
yHigh-density fin placement maximizes heat dissipation area
yValue adding accessories
yBase Maerial : Copper w/ Ni coating
yFin Material : Aluminum fin
yRated Current :
0.13Amp (2,000rpm) ~ 0.18Amp(2,450rpm)
yAirflow : 41~48.5 CFM
yLife Expectancy : 40,000 hr
yTotal Weight : 430 g
yApplication :
Intel®Pentium®
4 LGA775
Intel®Pentium®4 478
AMD AthlonTM (939 / 754) / AM2 (940)
Feature
Specification

- 5 - GH-PDU22-SC
English
<Warranty coverage does not include the following>
Incorrect method of operation or use of product not for intended use
Operational use beyond the advised standards (eg. overclocking)
Inability to install the product as a result of incompatibility with the motherboard used
Damage of product as a result of other product components
Any form of alteration to original product
A faulty product that leads to harm or damage to other products
Damage caused by natural disasters (eg. earthquake, fire, flood)
Products with a warranty sticker that is removed, torn or unreadable
Due to the weight of the cooler exceeding normal standards, please remove the cooler before computer transport to
prevent damage to the cooler itself as well as prevent problems during installtion.
The cooler fan speed levels provided are for reference use only. Please refer to the motherboard BIOS to verify
actual fan speed levels.
Before use, please remove the bottom protective layer of the cooler.
Please make sure the computer is turned off and its power disconnected prior to installation.
Precautions
Warranty Item

- 6 -
GH-PDU22-SC
English
Figure 1
Place the LGA775RM onto the LGA775 motherboard so that
side A is parallel with ARM and side B is parallel with CAM.
Figure 2
From the underside of the motherboard, use screws (4) and
plastic washers (4) together to secure the LGA775RM into
place..
Installation Instructions for P4 LGA775RM & Cooler
Figure 1
Figure 2
Figure3- 1 Figure3-2
Side A Side B Please add an adequate layer of heat sink
paste on the surface of the CPU.
ARM
CAM
Plastic
Washers
Figure 3
Gently push down on the cooler unit to lock it into position.
(Figure3-1).Connect the 3-pin connector to the CPU fan
connector on the motherboard.(Figure 3-2).Installation is now
complete.
If fan speed control is required, please refer to "Installation of the
Fan Speed Control Cable".
Note: About P4 Clips installation, please refer to “Installation
Instructions for Intel® Pentium®4 mPGA478 Clips”
To install GH-PDU22-SC on LGA775
motherboard needs both LGA775 RM & P4
clips.

- 7 - GH-PDU22-SC
English
Installation Instructions for Intel® Pentium®4 mPGA478 Clips
Figure 2
Clip introduction--
Part A: Secured to the retention mechanism hook.
Part B: Tightly contact the cooler bracket.
Part C: Secured to the retention mechanism hook.
Figure 1-1 Figure 1-2
Figure 3-1
Figure 4
Figure 3-2
Figure 4
Connect the 3-pin connector to the CPU fan connector on the
motherboard. Clips Installation is now complete.
If fan speed control is required, please refer to "Installation of
the Fan Speed Control Cable".
A
B
C
Figure 2
Figure 1
Please add an adequate layer of heat sink paste on the surface
of the CPU(Figure1-1). Figure 1-2 showing the correct
installation of the cooler atop the CPU.
Figure 3
Secure Parts A, B, and then C of the clip to the retention
mechanism. Assure that Part C is secured to the retention
mechanism hook on the same side as the heat pipes.

- 8 -
GH-PDU22-SC
English
Figure 1-1
Figure 2
Figure 3
Figure 4-1
Figure 1
Please add an adequate layer of heat sink paste on the surface
of the CPU.
Figure 2
Figure showing the correct installation of the cooler atop the
CPU.
Figure 3
Align the three insert spaces of the clip with the three juts on
the CPU socket and then push firmly downwards to hold the
clip in space.
If AM2, only need to hook up the middle of protuberant point.
Installation Instructions for AMD AM2 (940) / K8 (939 / 754) Clip
Figure 1-2
Figure 4-2
Figure 4
Push the lever on the side of the cooler towards the lever
position on the base of the CPU to secure the cooler atop the
CPU. Connect the 3-pin connector to the CPU fan connector
on the motherboard. Clip Installation is now complete.
If fan speed control is required, please refer to "Installation of
the Fan Speed Control Cable".

- 9 - GH-PDU22-SC
English
Installation of the Fan Speed Control Cable
Figure 1
Connect the 3-pin cooler power connector to the white
connector of the fan speed control cable.
Figure 2
The figure on the left shows the completed connection.
Figure 3
Connect the other side of the cable to the CPU fan connector
located on the motherboard. The original fan speed of 2,450
rpm will then drop down to 2,000 rpm.
Figure 1
Figure 2
Figure 3

- 10 -
GH-PDU22-SC
English