Gigabyte GH-PCU23-VE User manual

<Precautions>
yThe cooler fan speed levels provided are for reference use only. Please refer to the motherboard BIOS to verify actual fan speed levels.
yOnce the power supply cable is connected to the PCB of the cooler, please secure the partly transparent cover of the cooler prior to operation.
<Warranty coverage does not include the following>
yIncorrect method of operation or use of product not for intended use
yOperational use beyond the advised standards (eg. overclocking)
yInability to install the product as a result of incompatibility with the motherboard used
yDamage of product as a result of other product components
yAny form of alteration to original product
yA faulty product that leads to harm or damage to other products
yDamage caused by natural disasters (eg. earthquake, fire, flood)
yProducts with a warranty sticker that is removed, torn or unreadable
yDue to the weight of the cooler exceeding normal standards, please remove the cooler before computer transport to prevent damage
to the cooler itself as well as prevent problems during installtion.
yBIOS
yPCB COVER
y
y( )
y
y
y
y
y( )
y
y

GH-PCU23-VE
REV.1001
060410
Intel®Pentium®4 LGA775 / mPGA478
AMD AM2 / K8
Installation Guide

Table of Contents
Checklist ...................................................................................................................... 8
Specifications ................................................................................................................ 9
Features ...................................................................................................................... 9
Installation Instructions for Intel®Pentium®4 LGA775 RM & Cooler ............................. 10
Installation Instructions for Intel®Pentium®4 mPGA478 Cooler & Clips ........................ 11
Installation Instructions for AMD AM2 / K8 Cooler & Clip ............................................. 12
Power Connection and Installation of the 3.5" Drive Bay Fan Speed Controller ......... 13
Power Connection and Installation of the PCI Slot Bracket Fan Speed Controller ....... 14
Special Design ........................................................................................................... 15

- 8 -
GH-PCU23-VE
English
(1) GH-PCU23 -VE Cooler
Before use, please remove the protective film from the bottom of the cooler.
Prior to installation, make sure that the computer is turned off and its power is disconnected.
(2)GH-PCU23-VE
User's Manual
(3) Heat Sink Paste
(4) 3.5" Drive Bay Fan
Speed Controller
(5) PCI Bracket
(6) Power Cable
(8) P4 Clips
(10) Screws
(9) AM2 / K8 Clip
(7) LGA775 RM
Checklist

- 9 - GH-PCU23-VE
English
yHeat Sink Dimension : 112 x 112 x 175 mm
yFan Dimension : 92 x 92 x 25 mm
yHeat Pipe Number : 4
yBase Material : Copper
yFin Material : Aluminum
yRated Voltage : 12V
yRated Current : 0.38A
yFan Speed : 1,500 ~ 3,000 RPM
yNoise : 16 ~ 33.5 dBA
yBearing Type : Ball Bearing
yDual Rocket Airflow Design Fan Duct - for better performance and silent environment
yFour high conductivity heat pipes design
yHigh density precise forging copper bottom
ySuper large aluminum fins for more thermal area
yLinear fan speed control on 3.5'' front panel or rear PCI bracket
yChangeable fluorescent rings (Blue / Green / White / Orange)
yLife Expectancy : 50,000 hr
yCompatible CPU :
Intel®Pentium®Extreme Edition 955/840
Intel®Pentium®D Processor 960/840
Intel®PentiumR 4 Processor 670/570
Intel®Pentium®4 478 3.4GHz
AMD AM2 Series
AMD AthlonTM FX62
AMD AthlonTM 64x2 5200+
AMD AthlonTM 64 4000+
Specifications
Features

- 10 -
GH-PCU23-VE
English
Figure 1.
Place the LGA775 RM onto the LGA775
motherboard so that side A is paralleled with the
ARM and side B is paralleled with the CAM.
Figure 2.
On the underside of the motherboard, secure a screw with a washer in one of the four holes
located adjecent to the processor socket. And do the same for the remaining three holes.
Figure 1
Figure 2
Figure 3-1 Figure 3-2 Figure 3-3
Figure 3.
Place the cooler on the CPU socket and secure it
with the P4 clips (Figure 3-1). Connect the 3-pin fan
cable connector of the cooler to the motherboard
CPU fan header (Figure 3-2). Then the installation
is now complete (Figure 3-3).
To install P4 clips, please refer to "Installation Instructions for Intel® Pentium®4 mPGA478 Cooler & Clips."
Side A Side B
Installation Instructions for Intel®Pentium®4 LGA775 RM & Cooler
Plastic
Washers
ARM
CAM

- 11 - GH-PCU23-VE
English
Installation Instructions for Intel® Pentium®4 mPGA478 Cooler & Clips
Figure 2.
Hook one end of the clip to one of the RM hooks (Figure 2-1). Secure the
other end to the hook on the other side by pushing down on the handle
(Figure 2-2). Do the same for the other clip.
Figure 2-1
Figure 1.
Apply a thin layer of heat sink paste to the surface of the CPU (Figure
1-1) and then place the cooler atop the CPU (Figure 1-2).
Figure 1-1 Figure 1-2
Figure 3-1
Figure 3.
Connect the 3-pin fan cable connector of the cooler to the motherboard
CPU fan header (Figure 3-1). Then the installation is now complete
(Figure 3-2).
Please refer to page 13 & 14 for power connection and installation of the fan speed controller.
Figure 2-2
Figure 3-2

- 12 -
GH-PCU23-VE
English
Installation Instructions for AMD AM2 / K8 Cooler & Clip
Figure 1.
Apply a thin layer of heat sink paste to the surface
of the CPU (Figure 1-1). Put the AM2/K8 clip on to
the cooler as shown in Figure 1-2. Put the cooler
onto the CPU (Figure 1-3).
Figure 1-1
Figure 2-1
Figure 2.
Align and secure one side of the clip (Figure 2-1). On the other side , also
align the clip with the mounting lugs and then carefully push straight down
on the clip to hook it to the retention frame. For AM2 CPU, hook the clip to
the center mounting lug on the retention frame (Figure 2-2).
Figure 3-1 Figure 3-2 Figure 3-3
Figure 3.
Close the clip lever as shown in Figure 3-1 and
Figure 3-2 to secure it to the retention frame.
Connect the fan cable connector of the cooler to
the motherboard CPU fan header. Then the
installation is now complete (Figure 3-3).
Please refer to page 13 & 14 for power connection and
installation of the fan speed controller.
Figure 1-2 Figure 1-3
Figure 2-2

- 13 - GH-PCU23-VE
English
Power Connection and Installation of the 3.5" Drive Bay Fan Speed Controller
Figure 1-1
Figure 1.
Connect one end of the provided power cable to the 3-pin header on
the cooler (Figure 1-2).
Figure 3.
Secure the 3.5" drive bay fan speed controller in a free drive bay with
the provided screws (Figure 3-1). Connect the small 3-pin power cable
from the controller to the small 3-pin header on the cooler (Figure 3-2).
Figure 4.
Start your computer after the installation is complete. If there is an item
that allows for CPU fan speed control in system BIOS Setup, disable the
function. Use the fan speed controller to adjust the fan speed based on
your requirements.
Figure 3-1
Figure 4
Figure 1-2
Figure 3-2
Figure 2
Figure 2.
Connect the other end to the motherboard 3-pin or 4-pin CPU fan
header (Figure 2).

- 14 -
GH-PCU23-VE
English
Power Connection and Installation of the PCI Slot Bracket Fan Speed Controller
Figure 1.
Remove the knob, bolt and controller from the 3.5" drive bay fan speed
controller panel in sequence (Figure 1-1). Secure the controller, then the
bolt and finally the knob to the PCI bracket (Figure 1-2).
Figure 1-1
Figure 3-1
Figure 4
Figure 1-2
Figure 3-2
Figure 2
Figure 2.
Place the PCI bracket with the fan speed controller in the selected PCI
slot. Use screws to secure the PCI bracket in place.
Figure 3.
Connect one end of the provided power cable to the 3-pin header on
the cooler (Figure 3-1). Connect the other end to the motherboard 3-pin
or 4-pin CPU fan header. Connect the small 3-pin power cable from
the controller to the small 3-pin header on the cooler (Figure 3-2).
Figure 4.
Start your computer after the installation is complete. If there is an item
that allows for CPU fan speed control in system BIOS Setup, disable the
function. Use the fan speed controller to adjust the fan speed based on
your requirements.

- 15 - GH-PCU23-VE
English
Special Design
yyyyyChangeable Fluorescent Rings
(Colors: Blue / Green / White / Orange)
yy
yy
yDual Rocket Airflow Design Fan Duct
For better performance and silent environment. To achieve the best cooling effect, place the sealed side
toward the inside of the case.
Install the upper fan duct depending on the case you use.
Sealed Side
Air Outlet Side y
ySealed Side
Air Outlet Side y
yyyyyFluorescent Ring
yy
yy
yDual Fan Duct Design
y
yAir Outlet Side

GH-PCU23-VE
Intel®Pentium®4 LGA775 / mPGA478
AMD AM2 / K8
REV.1001

............................................................................................................... 18
................................................................................................................ 19
............................................................................................................... 19
Intel®Pentium®4 LGA775 ............................................ 20
Intel®Pentium®4 mPGA478 ......................................... 21
AMD AM2 / K8 ............................................................ 22
3.5 .................................................. 23
PCI .................................................................. 24
............................................................................................................... 25

- 18 -
GH-PCU23-VE
(1) GH-PCU23 -VE
(2)GH-PCU23-VE
(3)
(4) 3.5
(5) PCI
(6)
(8) P4
(10)
(9) AM2 / K8
(7) LGA775

- 19 - GH-PCU23-VE
y112 x 112 x 175 mm
y92 x 92 x 25 mm
y4
y
y
y12V
y0.38
y1,500 ~ 3,000 RPM
y16 ~ 33.5 dBA
yBall Bearing
y
y
y
y
y(3.5 PCI )
yGamer ( / / / )
y50,000
y
Intel®Pentium®Extreme Edition 955/840
Intel®Pentium®D Processor 960/840
Intel®PentiumR 4 Processor 670/570
Intel®Pentium®4 478 3.4GHz
AMD AM2 Series
AMD AthlonTM FX62
AMD AthlonTM 64x2 5200+
AMD AthlonTM 64 4000+

- 20 -
GH-PCU23-VE
1.
LGA775 LGA775
ALGA775
BLGA775
2.
1
2
3-1 3-2 3-3
3.
LGA775 P4
(3-1)
CPU_FAN (3-2)
(3-3)
P4 "Intel® Pentium® 4 mPGA478 "
23 24
AB
Intel®Pentium®4 LGA775