Gigabyte GC-WBAX2400M User manual

GC-WBAX2400M
GC-WBAX2400R
Installation Guide/安裝指南
安装指南/インストールガイド
Installationsanleitung

- 2 -
Installing the Wi-Fi/Bluetooth Card • 安裝Wi-Fi/藍牙卡
安装Wi-Fi/蓝牙卡 • Wi-Fi/Bluetoothカードを取り付ける
Installation der Wi-Fi/Bluetooth-Karte
Antenna Connector
天線連接埠
天线连接端口
アンテナ コ ネクター
Antennenanschluss
Wi-Fi/Bluetooth Card
Wi-Fi/藍牙卡 • Wi-Fi/蓝牙卡
Wi-Fi/Bluetoothカード
Wi-Fi/Bluetooth-Karte
USB Connector • USB連接埠插座
USB连接端口插座 •
USBコネクター • USB-Anschluss
Antenna • 天線
天线 • アンテナ•Antenne
USB Cable • USB排線
USB排线 • USBケーブル
USB-Kabel

- 3 -
Step 1:
Install the Wi-Fi/Bluetooth card in a PCI Express x1
slot. Connect one end of the USB cable to the USB
connector on the Wi-Fi/Bluetooth card.
步驟一：
先將Wi-Fi/藍牙卡安裝至PCI Express x1 插
槽，接著將USB排線的一端接至無線/藍
牙卡的USB連接埠插座。
步骤一：
先将Wi-Fi/蓝牙卡安装至PCI Express x1插
槽，接着将USB排线的一端接至无线/蓝
牙卡的USB连接端口插座。
ステップ 1:
Wi-Fi/Bluetooth カードを PCI Express x1 スロ
ットに装着します。USB ケーブルの一方の
端をWi-Fi/Bluetooth カードの USB コネクタ
に接続します。
Schritt 1:
Installieren Sie die Wi-Fi/Bluetooth-Karte in einem
PCI Express x1-Steckplatz. Verbinden Sie ein
Ende des USB-Kabels mit dem USB-Anschluss
auf der Wi-Fi/Bluetooth-Karte.

- 4 -
Step 2:
Connect the other end of the USB cable to the
F_USB connector on the motherboard.
步驟二：
再將USB排線的另一端接至主機板的
F_USB插座。
步骤二：
再将USB排线的另一端接至主板的F_USB
插座。
ステップ 2:
USB ケ ーブ ル の もう一方の端を マ ザ ー
ボードの F_USB コネクタに接続します。
Schritt 2:
Verbinden Sie das andere Ende des USB-Kabels
mit dem F_USB-Anschluss auf dem Motherboard.

- 5 -
Step 3:
Tighten the antenna cables to the antenna
connectors on the Wi-Fi/Bluetooth card
respectively.
步驟三：
將天線鎖至Wi-Fi/藍牙卡的天線連接埠。
步骤三：
将天线锁至Wi-Fi/蓝牙卡的天线连接端
口。
ステップ 3:
ア ン テ ナ ケ ー ブ ル を そ れ ぞ れ W i - F i /
Bluetooth カードのアンテナコネクター に
しっかりと接続します。
Schritt 3:
Befestigen Sie die Antennenkabel gut an den
jeweiligen Antennenanschlüssen auf der Wi-Fi/
Bluetooth-Karte.

- 6 -
Step 4:
Then move the antennas to a place where the
signal is good.
步驟四：
完成安裝後將天線移至收訊良好處。
步骤四：
完成安装后将天线移至收讯良好处。
ステップ 4:
次に、
ワイヤレス信号が受信し易い場所
にアンテナを配置します。
Schritt 4:
Setzen Sie die Antennen dann auf eine Stelle mit
gutem Signalempfang.

- 7 -
After the computer starts, please download the latest driver from GIGABYTE’s website
and install it. Adjust your wireless LAN configuration based on your environment after
installing the driver.
啟動電腦後請至技嘉網站下載最新的驅動程式並安裝。完成後即可依環境中
的無線網路選擇連接。
启动电脑后请至技嘉网站下载最新版的驱动程序并安装。完成后即可依环境中
的无线网络选择连接。
コンピューター起動後、GIGABYTE の ホ ームページから最新ドライバをダウンロ
ードし、 インストールしてくだ さい。 ドライバ の インストー ル後、 お客様の環境に
応じて無線LANの設定を調整してください。
Hat sich der Computer hochgefahren, laden den neuesten Treiber von der GIGABYTE-
Website herunter und installieren Sie ihn. Passen Sie nach Installation des Treibers Ihre
WLAN-Konfiguration entsprechend Ihrer Umgebung an.
Installing the Drivers and Utilities • 安裝驅動程式及工具
安装驱动程序及工具 •
ドライバとユーティリティをインストールする
Installation der Treiber und Dienstprogramme

- 8 -
Regulatory Notices
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Product Name: PCIe add-in card
Trade Name: GIGABYTE
Model Number: GC-WBAX2400M/GC-WBAX2400R
Responsible Party – U.S. Contact Information: G.B.T. Inc.
Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: [phone]
Internet contact information: https://www.gigabyte.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
United States of America, Federal Communications Commission Statement
The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF)
electromagnetic energy emitted by FCC certified equipment. The Intel PRO/Wireless 5000 LAN products meet the Human
Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the
instructions found in this manual will result in exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:
•Do not touch or move antenna while the unit is transmitting or receiving.
•Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body,
especially the face or eyes, while transmitting.
•Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.
•Use in specific environments:
- The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments.
- The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).
- The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.
Antenna use:
In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 7.9
inches (20 cm) or more from the body of all persons.
Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive
environment unless the device has been modified to be qualified for such use.

- 9 -
Antenna Warning
The wireless adapter is not designed for use with high-gain antennas.
Use On Aircraft Caution
Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals
could interfere with critical aircraft instruments.
Other Wireless Devices
Safety Notices for Other Devices in the Wireless Network: Refer to the documentation supplied with wireless Ethernet adapters or
other devices in the wireless network.
Canada, Canada-Industry Notice:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux normes Canada d’Industrie de RSS permis-exempt. L’utilisation est assujetti aux deux conditions
suivantes:
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its operation in the 5.15-to 5.25-GHz
frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce
the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the
5.25-to 5.35-GHz and 5.65 to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The
maximum allowed antenna gain for use with this device is 6dBi in order tocomply with the E.I.R.P limit for the 5.25-to 5.35 and 5.725 to
5.85 GHz frequency range in point-to-point operation. To comply with RF exposure requirements all antennas should be located at a
minimum distance of 20cm, or the minimum separation distance allowed by the module approval, from the body of all persons.
Attention: l’utilisation d’un réseau sans fil IEEE802.11a est restreinte à une utilisation en intérieur à cause du fonctionnement dansla bande de
fréquence 5.15-5.25 GHz. Industry Canada requiert que ce produit soit utilisé à l’intérieur des bâtiments pour la bande de fréquence 5.15-5.25 GHz
afin de réduire les possibilités d’interférences nuisibles aux canaux co-existants des systèmes de transmission satellites. Les radars de puissances
ont fait l’objet d’une allocation primaire de fréquences dans les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces stations radar peuvent créer des
interférences avec ce produit et/ou lui être nuisible. Le gain d’antenne maximum permissible pour une utilisation avec ce produit est de 6 dBi afin
d’être conforme aux limites de puissance isotropique rayonnée équivalente (P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz
en fonctionnement point-à-point. Pour se conformer aux conditions d’exposition de RF toutes les antennes devraient être localisées à une
distance minimum de 20 cm, ou la distance de séparation minimum permise par l’approbation du module, du corps de toutes les personnes.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

- 10 -
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radio électrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
European Union (EU) CE Declaration of Conformity
This device complies with the following directives: Electromagnetic Compatibility Directive 2014/30/EU, Low-voltage Directive
2014/35/EU, Radio Equipment Directive 2014/53/EU, ErP Directive 2009/125/EC, RoHS directive (recast) 2011/65/EU & the
2015/863 Statement. This product has been tested and found to comply with all essential requirements of the Directives.
European Union (EU) RoHS (recast) Directive 2011/65/EU & the European Commission Delegated Directive (EU) 2015/863
Statement
GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP,
DBP and DIBP). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE
are continuing our efforts to develop products that do not use internationally banned toxic chemicals.
European Union (EU) Community Waste Electrical & Electronic Equipment (WEEE) Directive Statement
GIGABYTE will fulfill the national laws as interpreted from the 2012/19/EU WEEE (Waste Electrical and Electronic Equipment) (recast)
directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of electric and electronic devices and their
components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.
WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed
of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
For more information about where you can drop off your waste equipment for recycling, please contact your local
government office, your household waste disposal service or where you purchased the product for details of environmentally safe
recycling.
End of Life Directives-Recycling
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of
with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
Déclaration de Conformité aux Directives de l’Union européenne (UE)
Cet appareil portant la marque CE est conforme aux directives de l’UE suivantes: directive Compatibilité Electromagnétique 2014/30/
UE, directive Basse Tension 2014/35/UE, directive équipements radioélectriques 2014/53/UE, la directive RoHS II 2011/65/UE & la
déclaration 2015/863. La conformité à ces directives est évaluée sur la base des normes européennes harmonisées applicables.