Gigabyte G-MAX FB User manual

G-MAXTM Micro ATX Series User’s Manual
P. E 1
Copyright Notice
Copyright 2001 Gigabyte Technology.
All Rights Reserved. No part of this documentation, including but not limited to the products
and software described in it, may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language, in any form or by any means without the
express written permission of Gigabyte Technology.
Trademarks
Products and corporate names appearing in this manual may be registered trademarks or
copyrights of their respective companies and are used only for identification or explanation
purposes without intent to infringe.
Other product names used in this manual may be trademarks or registered trademarks of
their respective owners.
The author assumes no responsibility for any errors or omissions that may appear in this
document nor does the author make a commitment to update the information contained
herein. Third-party brands and names are the property of their respective owners.
Disclaimer
The information contained in this documentation is subject to change without notice.
Gigabyte Technology makes no representations or warranties of any kind, either express
or implied, with respect to the contents hereof, including but not limited to implied
warranties of merchantability or fitness for a particular purpose. In no event shall
Gigabyte Technology. Be liable for any loss of profits, loss of business, loss of data,
interruption of business, or indirect, special, incidental, or consequential damages of any
kind arising from the use of this product or documentation. Gigabyte Technology reserves
the right to revise or change this product or documentation at any time without obligation
of Gigabyte Technology. To notify any person of such revision or changes.
May/2002

G-MAXTM Micro ATX Series User’s Manual
P. E 2
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacture.
Dispose of used batteries according
to the manufacturer’s instructions.
 Preface
This system unit is designed to be stable, safe, and easy to use. The system can be
upgraded and expanded in function easily if correct procedure is followed.
For your own safety and to avoid accidental damage to your system, please ensure you
follow the following precautions:
 Follow all the warnings and instructions marked on the products.
 To remove or clean the product, remember to unplug the power cord.
 Place your system unit in a cool, clean space, to be far away from water, heat and
dust.
 Before connecting any peripheral equipment, please unplug the power cord from the
system unit to prevent unexpected damage.
 The AC input supplies power to the system unit. Check your dealer if you can not
recognize the type of the power supply.
 Introduction
G-MAXTM series product, to adopt main board of design & development by GIGABYTE that
is Micro ATX mechanical design in advance, let you work smoothly in Windows
environment.
Micro ATX adopt dexterous mechanical design, so it is ease by assembly & safeguard.
Specification Overview
Micro ATX chassis
Micro ATX main board of GIGABYTE
Power supply
DVD-ROM / CD-ROM
1.44 “FDD
Multi I/O Card (Option)
Keyboard (Option)
Assembly Box Content
Main board user’s manual
User’s manual
Main board Driver CD
IDE cable
Cable Tie
Screw bag
Mouse (Option)
SPDIF cable (Option)

G-MAXTM Micro ATX Series User’s Manual
P. E 3
Software and
Manuals
Power Cord
PC
Mouse
(
O
p
tion
)
Keyboard
(Option)
Cables
 Items included in the package

G-MAXTM Micro ATX Series User’s Manual
P. E 4
I. Chassis
ŜDimension 405(D)mm x 180(W)mm x 352(H)mm
This chassis is made with material complied with UL specification and designed for
space saving and easy open with thumbscrew. There are two 5.25” and three 3.5”
drive bays. This chassis complies with corresponding EMC and safety regulations.
II. Motherboard
See Motherboard Manual for details.
III. Power Supply
The ATX switching power supply included with this product supports soft off function.
Hence, the system can be shut down automatically. Default input voltage setting is
230V.
Note: Please check the voltage requirements in the country you reside before
turning on the PC.
IV. System Component Installation
ŜRemove the screws of the side cover of the chassis, push backward to dismount the
cover.
ŜCPU
1. Insert the CPU on the CPU socket. Before installation, lift up the lever and align the
cut of the CPU with the marking on the socket.
2. Pull down the lever to lock the CPU on the socket after installation. When you are
installing the heat sink, please make sure to keep the heat sink tight against the
CPU to obtain the best cooling result.
3. Apply the thermal compound to one side of the template, and ensure the compound
is spread evenly across the template and repeat if necessary.
Remove front panel

G-MAXTM Micro ATX Series User’s Manual
P. E 5
Install fan on to
p
of CPU
Click the heat sink
locker to the
motherboard
retention module.
4. Connect fan power connector to the CPU FAN connector on the motherboard.
A. For Intel
Pentium 
4 processors
B. For AMD AlthlonTM and AMD DuronTM processors
Set CPU clock frequency from BIOS Setup, see Motherboard Manual for details.
Leve
r
CPU Pin
Apply thermal grease to the top
of the CPU properly.
Lever
CPU Pin
Apply thermal grease to the top
of the CPU properly.
Install fan on top o
f
CPU
Click the heat sink locker to the
motherboard retention module.

G-MAXTM Micro ATX Series User’s Manual
P. E 6
Locks: make sure they hook up the notches at sides of module
ŜMemory
In this section we will guide you to install memory module. First, make sure the
position notches at the bottom of the module should align to the pins on the module
sockets on the motherboard, then push the module downward until the locks hook
up notches at sides.
Position notches. Make sure that the notches should align the pin on memory
slot on the motherboard
Notches at sides
of module
DDR
Notches at sides
of module
Position notches. Make sure that the notches should align the pin on memory
slot on the motherboard
SDRAM

G-MAXTM Micro ATX Series User’s Manual
P. E 7
ŜHard Drive Installation
1.Remove 3 screws in front of the hard drive chassis and dismount chassis.
2.The chassis accommodates up to three 3.5” storage devices. Select a place and fix
the hard drive with screws.
3.Connect the IDE cable included in the accessory box to the connector on the hard
drive. Make sure that the RED wire on the ribbon connects to PIN 1 of the hard drive.
Connect to hard drive
3.5”Floppy
Drive
Hard drives

G-MAXTM Micro ATX Series User’s Manual
P. E 8
4.Connect power connector to the hard drive.
5.Install chassis back to position after completing hard drive installation.
6.Connect the other end of the IDE connector to the IDE-1 bus on the motherboard.
HDD frame

G-MAXTM Micro ATX Series User’s Manual
P. E 9
7.Check all connections again.
Put back front panel
Put back side panel

G-MAXTM Micro ATX Series User’s Manual
P. E 1 0
V.System Installation and User’s Guide
ŜFront Panel
Floppy
Power Button
Power LED
HDD LED
CD-ROM Eject Button
CD-ROM Slot
Floppy Drive
Eject Button
Floppy LED
*LINE OUT
*MIC IN *USB Hub
*1394 Port
*PCMCIA Port
*PCMCIA Button *SPDIF
Notice!!
A. For those models with front audio module:
B. If you use microphone for recording, please insert it in
the Front Audio Port.
G-MAX
TM
Micro ATX Front Audio Port
*LINE OUT
*MIC IN
*USB Hub

G-MAXTM Micro ATX Series User’s Manual
P. E 11
ŜRear Panel
ŜNote
1.To avoid breaking disc during high-speed operation, we recommend you to use
high quality CD/ Recordable CD/ Re-writable CD.
2.Specification with “Ŏ” mark are subject to change without notice.
ŜImportant Safety Instructions
Caution –To reduce the risk of fire, use only No.26 AWG or larger telephone line cord.
Caution –Always disconnect all telephone lines from the wall outlet before servicing
or disassembly this equipment.
Caution –Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.
Dispose used batteries according to the manufacturer’s instructions.
Power Inlet
Keyboard Port (PS/2) Mouse Port (PS/2)
LPT Port
COM Port
COM Port / VGA Port
Voltage Switch
USB Hub
Game Port
A
udio In
A
udio Out
MIC In
*1394 Port
LAN Port