Gill 739120 User manual

739120
739120A
20' BALL STOP;
OFFSET POLE
Read all of the instructions before beginning. Make sure you have
all parts and tools you will need. Consult local codes and guidelines.
Local conditions may require a different procedure, the following
instructions should be considered recommended minimums.
CAUTION - contact your local utility companies to locate burried
electrical, gas, and water lines before digging holes for footings.
Also check for overhead utilities.
ALWAYS LOWER NETS IN HIGH WIND STORMS
www.gillathletics.com
Copyright

2017 by Gill Athletics.
All rights reserved.
800-637-3090
2/17/2017
INST739120
Page 1 of 7
20' OFFSET BALL STOPS
ASSEMBLY INSTRUCTIONS

40"
2'-0"
5"
2'-0"
40"
SLEEVE ALIGNMENT HOLE
GROUND LEVEL
NET
ENSURE PROPER
STOP BOLT
ORIENTATION
2 1
2
"
1 1
2
"
1. Locate and dig footings for each upright. Poles are set in ground sleeves.
Confirm all locations before setting.
Position and level gravel or a flat concrete pad in the bottom of the hole so
that the sleeve opening rests at the proper height at the surface.
Fix and support the sleeve in position with wire and/or sections of rebar to
prevent sleeve movement during the concrete pour.
During the pour, ensure the alignment holes at the top opening of the sleeve
remain properly aligned. These holes help orient the pole alignment pins at
the bottom of the sleeves.
The footer size is to be determined by the architect/engineer and is based on
local codes and soil conditions.
Concrete must be allowed to fully cure before continuing
NET ANCHOR PIERS:
1. Dig a 5" x 24" deep hole for each net
anchor pier. Piers should be placed 38" to 40"
in front of each net pole.
2. During the concrete pour for the ground
sleeves, fill each hole to within 1-1/2" of the
surface level. This will place the eyebolt
anchor point below the surface level so as not
to interfere with mowing.
3. After concrete has cured, drill a 1/2" x 2
1/2" deep hole in the center of the pier for the
stainless steel threaded anchor. Clean the
hole and insert the threaded anchor. Seat the
anchor with a 5/16" pin punch and install the
3/8" eyebolt.
www.gillathletics.com
Copyright

2017 by Gill Athletics.
All rights reserved.
800-637-3090
2/17/2017
INST739120
Page 2 of 7
20' OFFSET BALL STOPS
ASSEMBLY INSTRUCTIONS

If Net Anchor Piers are not used, move the net rope guide to
the through hole at the base of the pole. Secure the bottom
of the net and lower net cable to this eye nut and bolt.
OPTIONAL
www.gillathletics.com
Copyright

2017 by Gill Athletics.
All rights reserved.
800-637-3090
2/17/2017
INST739120
Page 3 of 7
20' OFFSET BALL STOPS
ASSEMBLY INSTRUCTIONS

HDWE012570E0
5/16" x 5.5" BOLT
M1232
NOTE:
ROPE CLEAT CAN BE INSTALLED
ON EITHER SIDE OF POLE
DETERMINE LOCATION IN FIELD
CLEAT
M2244
NYLOCK NUT
TOP CAP
LOCKWASHER
HDWE53003000
HDWE012560E0 PCAP00158002
HDWE040010E0
M2591
HDWE53003000
HDWE012560E0
HDWE040010E0
M2591
FLATWASHER
LOCKWASHER
2. Assemble the top cap, rope cleat, and eye nuts as shown
NOTE: THERE ARE 2 DIFFERENT BOLTS USED IN THIS STEP, 5.5" AND 5" LONG
USE THE 5.5" BOLT ON THE ROPE CLEAT
EYE NUT
FLATWASHER
5/16" x 5" BOLT
EYE NUT
5/16" x 5" BOLT
www.gillathletics.com
Copyright

2017 by Gill Athletics.
All rights reserved.
800-637-3090
2/17/2017
INST739120
Page 4 of 7
20' OFFSET BALL STOPS
ASSEMBLY INSTRUCTIONS

L
PULLEY
PULY00100
M2223
SNAP HOOK
3. Attach the pulley.
www.gillathletics.com
Copyright

2017 by Gill Athletics.
All rights reserved.
800-637-3090
2/17/2017
INST739120
Page 5 of 7
20' OFFSET BALL STOPS
ASSEMBLY INSTRUCTIONS