GiveBest HPU15A-E User manual

Digital Ceramic HeaterDigital Ceramic Heater
With Remote Control
Owner's Manual
Model: HPU15A-E
GiveBest

2

3

Parts of the Heater
1.
2. LED Display
3. Safety Grille
4. Base
5. Remote Control
6. Power Light
Control Panel
Symbols
1. Place the heater on a firm, level surface, after assembling per
this manual. Plastic or rubber tabs, like the feet on this unit, may
stick to furniture surfaces and/or hardwood floors. The unit may
leave a residue that could darken, stain or leave permanent
blemishes on the finish of certain furniture surfaces, including
wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt AC outlet. Be sure that the
plug fits tightly into outlet. When plugs fit loosely into
receptacles, they may slip partially or completely out of the
receptacle with only the slight movement of the attached cord.
Receptacles in this condition may overheat and pose a serious
fire hazard; if covered by a curtain or drape, the fire hazard is
even greater.
3. When the heater is initially plugged in, there will be a "beep"
and the
Power Light will come on indicating that there is power
to the unit. The Power Light will remain lit until the heater is
unplugged from the electrical outlet. (Figure 2)
4. Turn the heater ON by pressing the Power Button
.
GH heat.
H heat.
(Figure 2)
Power Button
H/L Heat Button
High Temperature Setting Button
Low Temperature Setting Button
Timer Button
Figure 2
Operation
(Figure 1)
Figure 1
2
3
1
4
6
4
6.
Upon turning the heater on, the unit will be in HI
Press the button to switch over LOW or HIG
5.
To turn the heater OFF, press the Power Button . The
unit will first turn off the heating elements, the fan will be shut
down 30 seconds later. Unplug the unit by pulling the plug from
the electrical outlet only after the fan stopped.
7.

Oscillation
Pressing the
Oscillation Button
will allow the heater to
oscillate back and forth. To stop the oscillation, press the
Oscillation Button again. When the heater is in Automatic
Temperature Control, the oscillation function will stop when the
set temperature is reached and resume when the heater turns
back on.
Figure 3
Figure 4
5
Timer Function (Figure 3)
The timer function may be activated when the heater display is in
any function. This function allows you to set the length of time
the heater will run before turning itself off, from 1 hour to 8 hours.
Pressing the
Timer Button will increase the length of time
by 1 hour each time this button is pressed. After the display
reflects 8 hours, pressing the Timer Button once more will
reset the heater to run continuously. The heater will turn off when
the set time has elapsed. The unit can be turned back on by
pressing the
Power Button
.
Automatic Temperature Control (Figure 4)
1. To set the room at a specific temperature, press the or
buttons to the desired temperature. The heater is now in Auto
Temperature Mode and the indicator will glow on the
LED
display .
2. When the display shows the temperature at which you want to
set the unit, the set temperature will flash several times and then
the display will return to indicate the current room temperature
and will gradually change as the room temperature changes.
NOTE: The temperature display does not indicate the
temperature of the heated air being emitted by the heater.
3. Once the room temperature reaches 2 degrees above the set
temperature, the heater will shut off. Once the room temperature
reaches 2 degrees below the set temperature, the heater will
turn back on and continue to cycle off and on to maintain the set
temperature.
4. This function will cancel if the button is pressed.
NOTE: It is normal for the heater "fan" to run for approximately
30 seconds when the heater shuts off after reaching the set
temperature.

Figure 5
Remote Control (Figure 5)
The remote control uses two (2) "AAA" batteries (not included)
for operation.
Note: Change the batteries with new and same types if the
remote control does not operate well. Otherwise your remote
control may not operate properly. Remove the batteries out of the
remote control if you won't use the remote control for a long time.
Remaining batteries may damage your remote control.
Note: Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (nickel-cadmium)
batteries.
Battery Disposal - Please dispose of the used battery per
municipal or provincial law.
This heater is equipped with a safety tip-over switch, which is
located on the bottom of the heater. This feature cuts the main
power to the heater if it gets knocked over. If the heater does tip
over, simply stand it upright in order to resume operation.
This heater includes an Overheat Protection System that shuts
the unit off when a potential overheat temperature is reached. If
this occurs, the heater can only resume its normal operation after
resetting it. To reset the heater:
1. Unplug the heater and wait 10 minutes for the unit to cool down.
2. After the 10 minutes, plug the unit in again and operate
normally.
6

1. Perform the cleaning procedures described above.
2. Wipe all parts dry.
3. Pack the heater in a plastic bag and store it in a cool, dry place.
We recommend that you store the heater in its original carton.
If your heater fails to operate:
Make sure the electrical outlet or circuit breaker is working.
Check for obstructions. If you find an obstruction, turn the
heater OFF, and UNPLUG THE UNIT. Carefully remove the
obstruction and follow the reset instructions.
1. Press the Power Button to turn the heater OFF and unplug
the heater before moving or cleaning.
2. Interior dust can often be removed by using a vacuum cleaner
with a crevice tool attachment.
3. To clean the enclosure, use a clean, soft and lightly damp
cloth to gently wipe off the dirt from the surface of the unit. Be
sure not to wet the Heating Element and the switches. Allow the
unit to dry completely before use.
4. Do not use cleaning liquid or other chemicals to spray on the
unit.
7

8
Brand family: Brightown, Givebest
[email protected]
US [phone]
Mon-Fri 8AM-10PM(EST)
For customer service and warranty, contact us here