GJD Sapphire 1500 MK3 GJD005 User manual

ADJUSTMENT TO FACTORY SETTINGS
When connecting the unit to the electrical supply or when
the supply is interrupted, the indicators will ash for one
minute whilst the system settles. Pressing any button
during this time will start normal operation.
Internal adjustments panel
The factory settings are shown.
LIGHT ON TIME IN MINUTES
1 to 24 minutes:
The length of the light on time after the last detection
during darkness. The red detector indicators will stay on for
this time after the last detection day and night.
PULSE COUNT/WALK TEST
Select this symbol to assist in location alignment of the
detector beams during daylight installations. When the
detector beams are activated the external lights will stay on
for a period of 6 seconds.
1, 2 or 3
After completing the ‘walk test’ function, set the pulse count
to required level. The pulse count is the number of detector
beams that have to be crossed to trigger the system.
1. Will give fast response
2. Gives better immunity with good response
3. Gives highest immunity to false activation in poor
environments but us less responsive.
The GJD Sapphire is a single area security lighting
controller which enables external areas to be accurately
monitored.
It automatically switches up to 1500 watts of resistive
lighting at night for a pre-set period and can be manually
overridden when required. The controller incorporates an
audible warning tone and features four detector indicators
which illuminate when activated by detection day and night.
OPERATING INSTRUCTIONS
When a detector is activated day or night the relevant
detector indicator ickers and will remain on for the length
of the timer setting. During darkness the lighting will be
switched on automatically while the detector is receiving
activation signals, and will automatically turn off after the
pre set timer period.
The ‘Zone 1’ green indicator has to be selected for
automatically controlled lighting on detection during
darkness.
1
ZONE 1
ZONE 1
ZONE 1
Green indicator is ‘on’. This mode
must be selected for automatic
lighting during darkness.
Indicator ‘off’. Lighting and tone are
switch off.
Green indicator ashing. A detector
has activated the lighting.
Manually selecting this yellow
indicator will turn the lighting ‘on’.
Turning the indicator ‘off’ will return
to automatic mode.
Indicator ‘off’.
Yellow indicator ashing. A
detection has automatically
activated the lighting.
Red indicator ‘on’. Audible warning
tone selected. Zone 1 indicator to
be selected to function.
Indicator ‘off’ Audible warning tone
is switched off.
LIGHT ON
TIME MINS
PULSE
COUNT
1
3
5
10
24
1 2
3
Sapphire 1500 MK3
GJD005 Lighting Controller
Detect.Illuminate.Dete
r

CAUTION: To be installed by qualied personnel only:
1. Remote triggering of lights for the timer period. Pulse Count ‘1’ must be selected
2. Activate zone lighting for alarm period when linked to an intruder alarm panel.
All diodes: IN4148, IN4002 etc.
Caution if this equipment is intended for applications not specied pleas contact GJD prior to installation.
GJD reserve the right to alter the specication without notice.
2

3
SPECIFICATION
Supply 230 Vac 50Hz via ELCB/MCB - unit
fused at 10A
12 VDC@ 100mA GJD Opal XL (6mA) or Elite
Detectors (10mA) Optional external
12VDC piezo sounder up to
50mA
LOAD: Each Sapphire Controller can
switch up to
1500W of resistive load or 1000W
of inductive load. The
inductive load may require a
“snubber”
(suppressor) to manage the lamp
discharge current.
INDICATION: Four 24 hour detector indicators
which
pulse during detection and are
steady after detection for the
duration of the light on timer setting.
AUDIBLE Internal warning tone which
sounds on
detection day and night, and is
button selectable.
CONTROL: Controls up to 8 x GJD detectors.
Switches one area of lighting with
manual override when required.
OPTIONS: Ability to activate lighting with
remote push button.
Ability to have an auxiliary output.
Ability to activate lighting when
linked to an intruder alarm panel.
DIMENSIONS: 146(W) x 86(H) x 56(D) mm
Weight 495gm
MOUNTING: Indoor use only. Mount in a clean
dry location on a secure at
surface.
TEMPERATURE: -10 to +55 Centigrade
Certications
Self contained - Class 2 independently mounted control.

Unit 2, Birch Business Park, Whittle Lane, Heywood, Greater Manchester, OL10 2SX, UK
w: www.gjd.co.uk t: [phone] f: [phone]
ENGINEER NOTES