Glacier bay HD67688W-6004 Assembly instructions

THANK YOU
INSTALLATION AND CARE GUIDE
We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this lavatory
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
MODERN SINGLE HOLE TOUCHLESS
BATHROOM FAUCET
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
6/2021 REV.01HOMEDEPOT.COM
Model#
HD67688W-6001
HD67688W-6010H
HD67688W-6004
HD67688W-604405
Internet#
311893464
311893465
317147255
317147260
SKU#
1004931228
1004929183
1006463761
1006463760
With Deck Plate Without Deck Plate

2
Table of Contents
Important Information..............................2
Warranty ...................................................2
Pre-Installation.........................................2
Planning Installation ..............................2
Package Contents..................................3
Installation................................................4
Operation ..................................................11
Troubleshooting ......................................13
Care and Cleaning ................................... 12
Service Parts
........................................... 15
Adjustable
wrench
Safety
goggles
Phillips
screwdriver
SILICONE
Silicone
sealant
6mm
diameter
Electric
drill
Tools and Hardware Required ...............2
Important Information
□ Observe all local plumbing and building codes.
□ Cover the sink drain to avoid losing any parts.
□ Review the care and cleaning section included in this guide.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package
Contents list. If any part is missing or damaged, do not attempt to install the product. Contact Customer Service
for replacement parts.
TOOLS AND HARDWARE REQUIRED
Channel
lock pliers
Warranty
LIMITED LIFETIME WARRANTY
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.
Sensor mechanism excluded from Limited Lifetime Warranty and is covered by a 3-year warranty from date of
purchase. Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER
(1-855-434-5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original
consumer purchaser must be made available for all Glacier Bay warranty claims.
This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended
a five year limited warranty from the date of purchase, with all other terms of this warranty applying except the
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for
more details.
Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.
(2) Supply
lines

3
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
A 1Faucet
DWasher 1
C Washer 1
FDeck plate 1
GGasket 1
Part Description Quantity
ENut 1
BQuick connect
assembly 1
H 1
I Battery pack 1
Sensor control box
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
J"AA" Battery 4
Sensor Control Box
K
L
M
N
Press Pop-Up Assembly
K 1Top gasket
L 1Pop-up body
M 1Bottom gasket
N 1Nut
O 2Screw
H
+
-
-
+
+
-
-
+
I
J
A
B
D
E
C
F
G
O

Installation
4
1 Installing the faucet assembly
CAUTION: Always shut off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
□Shut off the water supply. Remove the old
faucet.
2 Securing the faucet assembly
□Install the washers (C & D) onto the threaded
mounting shank. Thread the nut (E) onto the
mounting shank. Lock the nut (E) into position
by tightening the screws (O). Do not
overtighten.
□WITH DECK PLATE: Align the holes in the
gasket (G) and deck plate (F) with the mounting
holes in the sink. Install the faucet body (A)-
including inlet tubes, hose (1) and sensor cable
(2)-through the middle hole in the deck plate (F).
□Clean the mounting surface.
□Remove the preassembled nut (E) and
washers (C & D) from the new faucet (A).
□WITH NO DECK PLATE: Install the faucet
body (A)-including inlet tubes, hose (1) and sensor
cable (2)-through the hole in the sink.
NOTE: Silicone sealant is required under the gasket (G).
A
2
1
SILICONE
A
F
G
2
1
□Loosen the screws (O) on the nut (E) until the
ends of the screws (O) are flush with the face
of the nut (E).
1
O
D
E
C
O
E
2
3

5
Installation (continued)
3Installing the sensor cable
□Install the sensor cable (1) to the control box connection (2). Ensure the arrows on the sensor cable and
control box connection are aligned to one another to ensure proper installation. Ensure they are tightly
connected by firmly pushing together.
□Secure the connection by hand tightening the nut (3) in a clockwise direction onto the threaded sensor cable.
CAUTION: If the connections are not made properly, the
sensor feature will not work.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
3
1
1
2
2
H

6
Installation (continued)
□Connect the hose with the yellow tag to the hose on the control box (H) with a matching yellow tag. Push
firmly together until they snap into place. As shown in the Fig 1.
□Connect the hose with the green tag to the hose on the control box (H) with a matching green tag. Push
firmly together until they snap into place. As shown in the Fig 1.
4Attaching the quick connector
to the receiving block
Fig 1
Yellow
Green
Green
Yellow
2
1
H

7
Installation (continued)
5Installing the batteries
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
NOTE: This step is for battery installation (optional). If the
battery will not be used, install as described in step 7.
□To open the battery housing, squeeze the tabs (1) on the cover (2), then remove the cover (2).
□Install the four AA batteries (J) included by matching the positive (+) and Negative (-) ends on the battery (J)
to the (+) and (-) markings in the battery pack (I). The negative ends of the battery (J) should always
connect to the spring end of the battery slots in the battery pack (I).
□Reinstall the battery pack cover (2) by pushing up and snapping into place.
NOTE: When the sensor flashes 10 times continuously
and slowly, the batteries have lost their charge. Replace
the batteries (J).
+
-
-
+
+
-
-
+
2
+-
+
+
-
-
3
4
4
J
I
I
1
1
2
5
2

8
Installation (continued)
6Installation using the battery
pack
NOTE: After installing the battery pack, the light on the
sensor will flash and the faucet control box will make a "click"
sound when you move your hand in the sensor area. If not,
check to ensure the batteries are installed correctly.
NOTE: This step is for battery installation (optional). If the
battery will not be used, install as described in step 7.
□Insert the battery pack cable (3) into the control box connection (4).
□Drill a hole in the wall using a 6mm (15/64 in.) diamater drill bit. Install the battery pack (I) using the molly
anchor (1) and screw (2) provided.
(15/64 in.) dia.
6mm
2
I
1
3
4
1
2

HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Installation (continued)
9
7Installation using the AC
adapter (not included)
NOTE: This step is for installation without batteries using
an AC adapter (not included). If using the batteries, install
as instructed in step 5 and skip to step 8. The AC adapter
is not included with the product, but can be purchased from
Homedepot.com.
□Install the AC adapter (3) into the power outlet.
□Insert the AC adapter cable (1) into the control box port (2).
NOTE: After installing the AC adapter, the light on the
sensor will flash and the faucet control box will make a
"click" sound when you move your hand in the sensor area.
If not, check if the connections are made properly.
1
2
3

10
Installation (continued)
8 Preparing the pop-up assembly
□Remove the bottom gasket (M) and nut (N) from
the top gasket (K) and pop-up body (L).
□Remove these pieces by pushing the bottom
gasket (M) down into the top of the nut (N) and
twisting together.
9 Installing the pop-up body
□Insert the pop-up body (L) into the sink. Ensure
that the top gasket (K) rests securely between
the top of the sink and the top of the pop-up
body (L).
10 Securing the pop-up body
□From underneath the sink, screw the bottom
gasket (M) and nut (N) assembly onto the
pop-up body (L) by twisting clockwise until
secure.
K
L
K
L
M
N
L
M
N