Gladiator GAGB28KDYG User manual

3/4-DOOR MODULAR
GEARBOX
Assembly Instructions
ARMOIRE À OUTIL AVEC
PORTE – 3/4
Instructions d’assemblage
GEARBOX MODULAR
DE 3/4 PUERTAS
Instrucciones de ensamblaje
In U.S.A. call: 1-866-342-4089
Aux États-Unis, composer le: 1866342-4089
En los EE.UU., llame al: 1-866-342-4089
W11430293C
In Canada call: 1-800-807-6777
Au Canada, composer le: 1800807-6777
En Canadá, llame al: 1-800-807-6777
www.gladiatorgarageworks.com
www.gladiatorgarageworks.ca
TABLE OF
CONTENTS TABLE DES MATIÈRES TABLA DE CONTENIDOS
Model/Modèle/Modelo:
GAGB28KDYG - Hammered Granite/Silver Tread
Ardoise martelée/texturé argenté
Granito Martillado/Plateado Huella
GAGB28KDKSG - Hammered Granite/Hammered Granite
Ardoise martelée/ardoise martelée
Granito Martillado/ Granito Martillado
GAGB28KDKW - Hammered White / Gray Slate
Blanc martelé/ardoise grise
Blanco Martillado / Pizarra Gris
CABINET SAFETY ...................................2
CABINET ASSEMBLY .............................2
PARTS.......................................................3
ASSEMBLY INSTRUCTIONS..................4
Tools and Parts .....................................4
Unpack the Cabinet .............................. 4
Assemble Cabinet.................................4
Complete the Assembly........................ 7
WEIGHT CAPACITY ................................8
ACCESSORIES ........................................8
WARRANTY .............................................8
SÉCURITÉ DE L’ARMOIRE ....................9
ARMOIRE.................................................9
PIÈCES ...................................................10
INSTRUCTIONS D’ASSEMBLAGE.......11
Outils et pièces..................................11
Déballage de l’armoire........................11
Assemblage de l’armoire ....................11
Fin de l’assemblage............................14
ACCESSOIRES ......................................15
GARANTIE..............................................15
SEGURIDAD DEL GABINETE...............16
CONJUNTO DEL GABINETE................16
PIEZAS ...................................................17
INSTRUCCIONES DE ENSAMBLAJE..18
Herramientas y piezas......................18
Desempaque del gabinete..................18
Ensamble del gabinete .......................18
Completar el ensamblaje ....................21
ACCESORIOS........................................22
GARANTÍA..............................................22

2
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your product. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
CABINET SAFETY
CABINET ASSEMBLY

3
P2
P3
P6
P5
P1
P11
P10
P9
P4
P8
P7
P7
D5
D1 D2
D3
D4
P7
P7
F1 F2 F3 F5
PARTS

4
ASSEMBLY INSTRUCTIONS
Tools and Parts
F1 F2 F3 F5
5/16" Hex-
head bolt
(24 required*)
Flange nut
(8 required*)
Phillips-head
screw
(52 required*)
Small ange
nut
(4 required*)
* For your convenience, 1 extra of each fastener has been
provided.
Gather the required tools before starting installation.
Tools Needed:
■1/2" Wrench ■Phillips screwdriver
■3/8" Wrench ■Level
Tool Supplied:
■Hex key
Part Supplied:
■Key
Unpack the Cabinet
1. Remove and verify the contents as shown in "Tools and Parts"
2. Dispose of/recycle all packaging materials.
1. Assemble Cabinet Frame
1. Place side panel (P1) on a at, rm surface so that the edge
with the holes facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel
(P1), with the edge with holes facing up as shown.
3. Align the holes and attach the top (P2) to side panel (P1) using
4 pcs 5/16" hex-head bolts (F1) and 2 pcs ange nuts (F2) as
shown. Do not tighten completely.
4. Position side panel (P3) so that the top (P2) is between the
edges of side panel (P3), with the edge with holes facing up
as shown.
5. Align the holes and attach the top (P2) to the side (P3) using
4 pcs 5/16" hex-head bolts (F1) and 2 pcs ange nuts (F2) as
shown. Do not tighten completely.
6. Insert cabinet bottom (P4) between the edges of side panels
(P1 and P3), with the edge with holes facing up as shown.
7. Align the holes and attach the bottom (P4) to the side panels
(P1 and P3) using 8 pcs 5/16" hex-head bolts (F1) and 4 pcs
ange nuts (F2) as shown. Do not tighten completely.
8. Stand the cabinet upright and fasten the front corners using
8 pcs 5/16" hex-head bolts (F1), 2 pcs at each corner. Do not
tighten completely.
P2
P1
P3
P4
P3
P2
A
F1
5/16" Hex-head bolt (24) F2
Flange nut (8)
Assemble Cabinet
■As you assemble the cabinet, make sure the edges with the
holes are facing up.
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
A. Edge with holes

5
2. Attach Lower Back Panel
3. Install Leveling Feet
1. Using 7 pcs Phillips-head screws (F3), attach the lower back
panel (P6) to the bottom (P4) and sides (P1 and P3) as shown.
Tighten screws completely.
1. Screw a leveling foot (P7) into each of the 4 pcs rivet nuts
located at the corners of the cabinet bottom as shown.
2. Stand the cabinet upright on to its leveling feet.
3. If you have not already, fasten the two bolts at each front
corner, of the cabinet frame. Completely tighten all the cabinet
bolts and nuts.
■The Gladiator®Modular GearBox is designed to be either
stationary or to roll on casters. To order the Gladiator®
"Modular GearBox Caster Kit", see “Accessories.”
F3
Phillips-head screw (7)
P1
P3
P2
P6
P4
P1
P4
P6
P5
A
P7
A. Leveling feet
4a. Assemble Drawer
■Position the drawer sides so that the glides are at the top and
facing the outside.
1. Working from the back, insert 3 pcs Phillips-head screws (F3)
through the drawer back and attach the side (D1) to the back
(D2) as shown.
2. Working from the back, insert 3 pcs Phillips-head screws (F3)
through the drawer back and attach the side (D3) to the back
(D2) as shown.
NOTE: Do not fully tighten the six screws attaching the
drawer back (D2) to the sides (D1 and D3).
3. Working from the top, set the drawer bottom (D4) down onto
the back and side anges as shown.
4. Working from the bottom, insert 7 pcs Phillips-head screws
(F3) through the drawer back (D2), sides (D1 and D3), and
then into the drawer bottom (D4) as shown.
F3
Phillips-head screw (13)
D4
D2
D3
D1