Goldair Platinum GPPH220 User manual

CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
•This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning the use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the
appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this heater. Covering this heater presents
fire risk and will activate the safety fuse; permanently disabling the unit.
WARNING: Do not use this heater in small rooms when they are occupied
by persons not capable of leaving the room on their own, unless constant
supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a minimum distance of 1 metre from the air outlet.
WARNING: In order to avoid overheating or fire, do not cover the heater.
General Care and Safety Guide
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.
•The heater must not be located immediately below a socket outlet.
•Do not use the heater if it has been dropped or damaged.
•Do not use if there are visible signs of damage to the heater.
•Ensure heater is on a flat, stable, heat-resistant surface.
•Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming
pool or other liquids.
•Keep all objects at least 1 metre from the front and 150mm from the sides of the appliance.
•This appliance is intended for household use only and not for commercial or industrial use.
•Indoor use only.
•Use only the voltage specified on the rating label of the appliance.
•Use this appliance only as described in this manual. Any other use is not recommended by
the manufacturer and may cause fire, electric shock or injury.
•The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging the appliance and vacuum cleaning the air
vents and grills.

•Never use the appliance to dry clothes.
•Always unplug appliance when not in use.
•Do not connect the appliance to mains supply until completely assembled and adjusted.
•Ensure hands are dry before handling the plug or main unit.
•Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to
become a hazard.
•Carry out regular checks of the supply cord to ensure no damage is evident
•Do not operate this appliance with a damaged cord, plug or after the appliance malfunctions
or has been dropped or damaged in any manner. Return to a qualified electrical person for
examination, electrical service or repair.
•Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to
weaken and split. Always ensure that all cord has been removed from any cord storage area
and is unrolled before use.
•It is recommended that this heater is plugged directly into the wall socket. Power boards are
not rated to supply power to high wattage appliances.
•A correctly specified, undamaged extension cord may be used with this heater provided it is
used in a safe manner.
•Do not remove plug from power socket until the appliance has been switched off.
•Do not remove plug from power socket by pulling cord; always grip plug.
•Do not place cord under carpet or cover with rugs or furniture. Arrange the cord so it cannot
be tripped over.
•Don’t place appliance on bedding or on thick & long carpet where the openings may get
blocked.
•Switch off and use handle provided when moving
•Do not place appliance close to radiant heat source.
•Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the appliance.
•Do not sit on the appliance.
•Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet)
rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning.
•Do not operate in areas where petrol, paint or other flammable liquids are used or stored.
•The appliance must not be immersed in any liquids.
•There are no user serviceable parts installed in the unit.
•Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.
•This unit is not supposed to be used in or around locations where foodstuffs, works of art or
delicate articles of science, etc are stored.
•When the appliance has been unpacked, check it for transport damage and ensure all parts
have been delivered. If parts are missing or the appliance has been damaged, contact the
Customer Services Team.
•If your appliance does not work, or is not working properly, contact the place of purchase or
the Customer Services Team.
General Care and Safety Guide
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

SCREW PACK
8 x SCREWS including 2 x ONE
WAY SCREWS TO ATTACH
FEET
WALL MOUNTING
6 x LONG SCREWS
4 x WALL PLUGS
Components
FEET x 2
CONTROL PANEL
HEAT OUTLET
AIR INLET
(BACK)
MAIN POWER SWITCH

FREE STANDING
1. Ensure the appliance is unplugged and power switches are off.
2. Carefully turn the Main Body upside-down on a scratch-free and stable surface. Be careful to
prevent damage to the cosmetic finish or your floor surfacing.
3. Align the screw hole on the Feet Bracket with the screw hole on the base of the appliance.
4. Attach feet with the screws provided and ensure the bracket sits firmly in place (do not over
tighten).
5. Set appliance upright and plug into a standard 240 volt AC electrical outlet.
Assembly and Installation
Before using this appliance, it must either be wall mounted or have the feet fitted.
The screw pack to attach the feet to your appliance will be taped to either one of the
feet for your appliance, or taped to the plug.

WALL MOUNTED
1. Make sure the appliance is unplugged and power switches are off.
2. Position the panel appliance within one metre of a wall socket. Do not mount in front of or
below the wall socket. Ensure there is at least 100mm clearance on all sides of the
appliance.
3. Assemble the bracket with the screws provided –see image 1.
4. Position the mounting screws on the wall per below mounting guide and check they are
horizontal with a spirit level. Ensure the bottom of the heater is at least 100mm from the
floor and drill holes as required. Fix the bracket to the wall.
5. Slot the back of the appliance onto the mounting screws. The bottom mount is on there to
keep the heater at the correct distance from the wall. You do not need to put a screw in the
bottom mount.
6. Plug appliance into a standard 240 volt AC electrical outlet.
Assembly and Installation
NOTE: Your Goldair Panel Heater should be installed with at least 100mm
clearance from the floor and any other surrounding parts including other
appliances, side walls and soft furnishings. There must be at least 1m
clearance from the top of the heater to ceilings or shelves.
Note: Do not run the power cord behind the heater.
WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT
COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS

Operating your Appliance
Always choose a safe location for the appliance, keeping in mind the safety precautions
outlined. Ensure all packaging has been removed from the unit before use.
WARNING: In order to avoid overheating or fire, do not cover the heater.
WARNING: Keep all objects at least 1 metre from the front, sides and rear
of the appliance.
WARNING: Do not use this heater with a programmer, separate timer,
remote-control system or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned
incorrectly.
WARNING:Never leave this heater unattended when in use.
Ensure heater is on a flat, stable, heat-resistant surface.
WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT
COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS
Once the heater is in a safe operating position and all switches are in the off position,
insert the power plug into the mains outlet.
CAUTION: Ensure the power cord is not tight because if pulled it may
partially pull the plug from the socket. A partially inserted plug will overheat
the plug and socket and could result in fire.
Note: When the appliance is turned on for the first time, it may release a
slight odour or smoke. This odour or smoke is a normal occurrence caused by
the initial heating of the internal heating elements and should not occur
again.
Do not use this heater until it is fully assembled according to the free standing or wall mounting
instructions within this manual.
CONTROL PANEL 1
5
6
8
2
3
7
4
1–Display
2–Up Button
3–Down Button
4–Power Button
5–Heat Setting Button
6–Timer Button
7–Receiver
8–Child Lock Button

OPERATION
Plug in the unit and switch on the main power switch. The power indicator will light up.
Press the Power button (4) to turn the unit on. The current room temperature will be displayed.
HEAT SETTINGS
Press the Heat Setting button (5) to set the heat level to either low or high.
SETTING THE TEMPERATURE
Press the Up (2) or Down (3) buttons to increase or decrease the temperature. If no buttons are
pressed for 3 seconds, the heater will run to the previously set temperature.
SETTING THE TIMER
Press the Timer button (6) to set timer. The set time is displayed. Press the Timer button to
increase the timer in one hour increments. The timer has a range of 0-24 hours. The unit will
turn off once the timer completes its countdown.
CHILD SAFETY LOCK
Press and hold the Child Lock button for 3 seconds to lock the system. A will be displayed.
To unlock, either turn the unit off or press and hold the Child Lock button for 3 seconds.
TURN OFF
Press and hold the Power button (4) to turn off the unit. The power indicator light will remain lit
while the main power switch is in the On position.
Operating your Appliance

TECHNICAL SPECIFICATION
Model No: GPPH220
Supply: 220-240VAC 50/60Hz
Wattage: 2000W
SUPPORT AND TECHNICAL ADVICE
Goldair –New Zealand
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[email protected]
Goldair –Australia
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[email protected]
Operating Your Heater
SAFETY DEVICE
This appliance has one protection devices:
•Resettable Thermal Link - this will automatically disconnect the power to the
appliance at a pre-set overheat temperature. After cooling down it will reset and
power on again. If this occurs, investigate what is causing the appliance to overheat.
CAUTION: The heater generates heat during use. Proper precautions must
be taken to prevent the risk of burns, scalds, fires or other damage to persons.
CARE AND CLEANING
•The heater requires regular cleaning to ensure trouble free operation:
•Unplug the heater from the mains supply before cleaning.
•Ensure that the heater has been allowed to cool down completely before cleaning.
•The common cause of overheating is deposits of dust or fluff in the appliance. Ensure
these deposits are removed regularly by unplugging the appliance and vacuum
cleaning the air vents and grills.
•Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and
dirt.
•Never use solutions such as petrol, thinners or polishing agents.
•Ensure the heater is dry before plugging back into the mains supply.
PROOF OF PURCHASE
To receive warranty retain receipt as proof of purchase.

WiFi –Downloading and Setting up APP
This APP is supported only on 2.4GHz Wi-Fi channels. Please ensure your phone is 2.4GHz
capable
Note this heater will only work within your home WIFI system.
This does not operate on 3G or 4G internet connections.
You will need a connection to your home Wi-Fi.
•Select your country code
•Enter your cellphone number
•Tap “Next”
You will then receive a text message with a verification
code.
Tap REGISTER near the bottom of the screen.
Download Goldair Heater mobile APP
•Open the APP Store or Google Play on your mobile phone.
•Open “Search” and enter “Goldair"
•Click “GET” and begin to download and install.
Once downloaded to your phone open the APP