Goldair Platinum GPPH620 User manual

Electronic Inverter Panel Heater with WiFi
Operating Instructions
Model: GPPH610, GPPH620, GPPH630

CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
•This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning the use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the
appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this appliance. Covering this appliance
presents fire risk and will activate the safety fuse; permanently disabling the
unit.
WARNING: Do not use this appliance in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a minimum distance of 1 metre from the air outlet.
General Care and Safety Guide
•Use only the voltage specified on the rating label of the appliance.
•Keep all objects at least 1 metre from the front and 150mm from the sides of
the appliance.
•This appliance is intended for household use only and not for commercial or
industrial use.
•Indoor use only.
•Use this appliance only as described in this manual. Any other use is not
recommended by the manufacturer and may cause fire, electric shock or
injury.
•Do not use the appliance if it has been dropped or damaged.
•The common cause of overheating is deposits of dust or fluff in the appliance.
Ensure these deposits are removed regularly by unplugging the appliance and
vacuum cleaning the air vents and grills.
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

•Never use the appliance to dry clothes.
•Always unplug appliance when not in use.
•When the appliance has been unpacked, check it for transport damage and
ensure all parts have been delivered. If parts are missing or the appliance has
been damaged, contact the Customer Services Team.
•Do not use if there are visible signs of damage to the appliance.
•Do not connect the appliance to mains supply until completely assembled and
adjusted.
•Ensure hands are dry before handling the plug or main unit.
•Ensure appliance is on a flat, stable, heat-resistant surface.
•Do not operate with cord set coiled up as a heat build up is likely, which could
be sufficient to become a hazard.
•Carry out regular checks of the supply cord to ensure no damage is evident
•Do not operate this appliance with a damaged cord, plug or after the appliance
malfunctions or has been dropped or damaged in any manner. Take to a
qualified electrical person for examination, electrical service or repair.
•Do not twist, kink or wrap the cord around the appliance, as this may cause the
insulation to weaken and split. Always ensure that all cord has been removed
from any cord storage area and is unrolled before use.
•It is recommended that this appliance is plugged directly into the wall socket.
Power boards are not rated to supply power to high wattage appliances.
•A correctly specified, undamaged extension cord may be used with this
appliance provided it is used in a safe manner.
•Do not remove plug from power socket until the appliance has been switched
off.
•Do not remove plug from power socket by pulling cord; always grip plug.
•Do not place cord under carpet or cover with rugs or furniture. Arrange the cord
so it cannot be tripped over.
•Don’t place appliance on bedding or on thick & long carpet where the openings
may get blocked.
•Switch off and use handle provided when moving
•Do not place appliance close to radiant heat source.
•Do not insert or allow foreign objects to enter any ventilation or exhaust
opening, as this may cause an electric shock, fire or damage to the appliance.
•Do not sit on the appliance.
•Do not use abrasive cleaning products on this appliance. Clean with a damp
cloth (not wet) rinsed in hot soapy water only. Always remove plug from the
mains supply before cleaning.
•Do not operate in areas where petrol, paint or other flammable liquids are used
or stored.
•Do not use this appliance in the immediate surrounds of a bath, a shower, or a
swimming pool or other liquids.
General Care and Safety Guide

•The appliance must not be immersed in any liquids.
•There are no user serviceable parts installed in the unit.
•Do not place the unit in wardrobes or other enclosed spaces as this may cause
fire hazards.
•This unit is not supposed to be used in or around locations where foodstuffs,
works of art or delicate articles of science, etc. are stored.
•If your appliance does not work, or is not working properly, contact the place of
purchase or the Customer Services Team.
General Care and Safety Guide

Components
CONTROL PANEL
HEAT OUTLET
AIR INLET
CASTOR WHEELS X 4
CASTOR WHEEL BRACKETS X 2
MAIN POWER SWITCH
WALL MOUNTING
BRACKET
SMALL FILTERS X 3
BIO FILTER

Before using this appliance, it must either be wall mounted or have the castor plates and
castors fitted.
This appliance has been supplied with ‘1 way screws’ for permanent installation of the
feet. This is a safety requirement for the New Zealand and Australian market.
Assembly Instructions
FREE STANDING
1. Ensure the appliance is unplugged and power switches are off.
2. Carefully turn the main body upside-down on a scratch-free and stable surface. Be
careful to prevent damage to the cosmetic finish or your floor surfacing.
3. Align the screw hole on the Castor Wheel Bracket with the screw hole on the base of
the appliance.
4. Attach Castor Wheel Bracket with the ‘1 way screws’ provided and ensure the
bracket sits firmly in place (do not over tighten). Firmly press Castor Wheels into
the slots provided on the Castor Wheel Bracket until they click into place. Some
force may be required.
5. Set appliance upright.
NOTE: The wall bracket edges may be sharp. It is recommended that if using as a free
standing appliance please remove the wall bracket from the back of the heater.

Installation Instructions
The appliance must not be located immediately below a socket outlet.
NOTE: Your Panel Heater should be installed with at least 150mm clearance from the
floor and any other surrounding parts including other appliances and side walls.
At least 300mm clearance from ceilings, shelves and soft furnishings.
Note:Do not run the power cord behind the heater.
WALL MOUNTED HEATERS ARE
ONLY TO BE MOUNTED ON HEAT
RESISTANT WALLS THAT COMPLY
WITH CURRENT AS/NZS
SPECIFICATIONS & BUILDING
REGULATIONS
150mm
300mm
150mm
150mm
WALL MOUNTED
1. Make sure the appliance is unplugged and power switches are off.
2. Position the panel appliance within one metre of a wall socket. Do not mount in front of or
below the wall socket. Ensure there is at least 150mm clearance on all sides of the
appliance.
3. Detach the mounting bracket from the back of the panel appliance by unscrewing the two
locking screws (located on the top of the mounting bracket).
4. Position the mounting bracket on the wall and mark the hole positions with a pen or pencil
and check they are horizontal with a spirit level. Ensure the two bottom mount holes are at
least 150mm from the floor and drill holes as required.
5. Secure the mounting bracket to the wall with the mounting screws. (For masonry walls use
the plastic sheaths).
6. Slot the back of the appliance onto the mounting bracket locating the bottom plugs first
and secure with two locking screws.
7. Plug appliance into a standard 240 volt AC electrical outlet.

Operating Your Heater
Always choose a safe location for the heater, keeping in mind the safety precautions
outlined. Ensure all packaging has been removed from the unit before use. Please
follow the below instructions.
WARNING: In order to avoid overheating or fire, do not cover the heater.
WARNING: Keep all objects at least 1 metre from the front and 150mm
from the sides of the appliance.
WARNING: Do not use this heater with a programmer, separate timer,
remote-control system or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned
incorrectly.
WARNING:Never leave this heater unattended when in use.
If mounted on castors, ensure heater is on a flat, stable, heat-resistant
surface.
Once the heater is in a safe operating position and all switches are in the off
position, insert the power plug into the mains outlet and switch on.
CAUTION: Ensure the power cord is not tight because if pulled it may
partially pull the plug from the socket. A partially inserted plug will overheat
the plug and socket and could result in fire.
Note: When the appliance is turned on for the first time, it may release a
slight odour or smoke. This odour or smoke is a normal occurrence caused by
the initial heating of the heating elements and should not occur again.

1. LED display
2. On/Off button
3. Mode setting button
4. Up button
5. Down button
6. Power setting button
7. Power indicator lights
8. Comfort indicator light
9. Economy indicator light
10. Anti-frost indicator light
11. Timer indicator light
12. Auto indicator light
13. User indicator light
14. WiFi button
8910 45
11 112 13 7632
14
Operating Your Heater

Press the button. A beep will sound indicating the heater is now on and the setting will be
“AUTO” mode. The current temperature will be displayed on the screen.
To turn the heater off, press the button for at least 2 seconds until the heater switches off.
AUTO Mode
In “AUTO” mode you can set either Comfort or Economy settings as shown below. The default
temperature setting is 25oC. Set your desired temperature by pressing the UP or DOWN
buttons. The screen will return to the current temperature after a few seconds but the set
temperature will be retained unless changed by you.
Comfort mode can be set from 5 –35oC
Economy mode can be set from 5 - 31oC (this is pre-set so there is always a 4oC
difference between Comfort and Economy settings)
You may want to set the economy temperature to a much lower level than the comfort
temperature and set the heater to economy when going to bed so that the room it is in stays
warm but not as hot as you would have it if you were in the room.
The heater will automatically set the best heat setting to reach the temperature you have set
and will adjust the heat setting to maintain the temperature you have set. The blue lights will
show which heat setting is currently in use.
USER mode
Press the button to change from AUTO to USER mode. The power setting will go to high (all
blue lights illuminated). You can select the power setting you want. There are 5 levels. The blue
lights will decrease with each push. When it reaches the bottom light (lowest heat setting) the
heater will then go back into AUTO mode.
In “USER” mode you can set either Comfort or Economy settings as shown below. The default
temperature setting is 25oC. Set your desired temperature by pressing the UP or DOWN
buttons. The screen will return to the current temperature after a few seconds but the set
temperature will be retained unless changed by you.
Comfort mode can be set from 5 –35oC
Economy mode can be set from 5 - 31oC (this is pre-set so there is always a 4oC
difference between Comfort and Economy settings)
You may want to set the economy temperature to a much lower level than the comfort
temperature and set the heater to economy when going to bed so that the room it is in stays
warm but not as hot as you would have it if you were in the room.
Check that the heater main power switch is in the OFF position before plugging into the mains
supply.
Turn the main power switch which is on the right hand side of the appliance just below the
control panel to the “I” position to turn the heater on. The heater will beep once and will be
stand by mode.
Operating Your Heater