GoldenDesigns GDI-7389-01 User manual

GDI-7289-01 / GDI-7389-01 / GDI-7689-01
2, 3 and 6 Person Saunas
OWNER’S MANUAL
FOR STEAM MODEL SAUNAS
REQUIRES 240VAC /1PHASE (30/40AMP, depending on your electrical
code) DEDICATED CIRCUIT FOR THE STOVE
REQUIRES 120VAC 15 AMP CIRCUIT FOR THE SAUNA
Please Note: The stove must be installed by a certified electrician per the
manufacturer’s manual. The stove must be installed per the electrical code
in your area with reference to the breaker and wire sizes. Models are
subject to change.

2
Thank you for the purchase of your new Steam Sauna! FOLLOW ALL INSTRUCTIONS AND BE
CAUTIOUS OF SAFETY SYMBOLS. All electrical wiring must be performed by a qualified licensed
electrician.
High Voltage Symbol: Be cautious as there is the presence of a high voltage current that flows through the
equipment!
General Caution Symbol: Be cautious as the equipment uses electrical current that can cause
serious injury.
1.Please read this Operating Instruction Manual thoroughly before use. This will allow the user to become
familiar with the operation of the control system. Please keep the Operating Instruction Manual available
for future reference. If any technical assistance or repairing is needed, please contact the manufacturer.
2. The steam sauna must be installed indoors or can be installed outdoors within the protection of a
structure that includes a water-proof roof protecting it from the outdoor weather elements. When not in
use and placed outdoors, a water proof cover must be used to cover the sauna room.
3. To reduce the risk of electric shock and/or fire, do not expose the control system to direct water
contact or rain. Do not open the cover to the control system as there are high tension fittings that can be
dangerous. Only dealer authorized qualified technicians should make any needed or necessary repairs
at any time.
4. Any repairs, alterations, or modifications to the control system are not authorized unless by an
approved repair technician. Any non-authorized repairs, alterations, or modifications can lead to
serious injuries and can cause the unit to work outside its intended specifications parameters.
5. Any non-authorized repairs, alterations, or modifications will void the warranty.
6. Before connecting the unit to a power source, please make sure that all wires, cords, and connections
are connected properly.
7. Make sure that the control system is in a well-ventilated and dry area. Do not place it next to any heat
source, in direct sunlight, where there is any type of vibration, or in any damp or dusty environment. It
should not be place in an area with other thermal-radiating objects.
8. When the equipment is not going to be used for an extended period of time, unplug the unit from the
power source.
9. Allow 30 seconds between turning the control system “On” and “Off”. By allowing 30 seconds between
powering the control system “On” and “Off” will prolong the life of the unit.
10. Confirm that you adhere to the correct power requirements of the control system. Connecting the
control system to other than the required voltage can damage the control system and possibly cause
serious injury. It is very important that the load parameters are consistent with that needed by the
control system.
11. Canadian Red Cedar and its rich aroma can cause an extremely small percentage of the population to
have an adverse reaction known as Multiple Chemical Sensitivity (MCS). While this is not an universally
recognized disorder in the medical field, certain consumers have an adverse physical reaction to low
levels of many common chemicals and cannot tolerate any aromatic oils, shampoos with perfumes
infused or certain herbs with natural aromas. However, for the majority of the population, Canadian Red
Cedar is the sauna wood of choice.

3
CAUTION: Exit sauna immediately if you feel dizzy, sleepy, or
any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY
GDI-7289-01
*The above assembly diagram is for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.

4
GDI-7289-01
Schematics
*The above assembly diagram is for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.

5
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY
GDI-7389-01
*The above assembly diagram is for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.

6
GDI-7389-01
Schematics
*The above assembly diagram is for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.

7
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY
GDI-7689-01
*The above assembly diagram is for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.

8
GDI-7689-01
Schematics
*The above assembly diagram is for quick
reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.

9
TABLE OF CONTENTS
Product Introduction 9
Parts Description 9
Assembly Instructions 11
Control Panel Operation 24
Tips for Using Your Sauna 26
Safety Instructions 27
Safeguards for Your Sauna 28
Warranty 29
Warranty Card 31
WARNING: Visually inspect all parts before assembly to make sure they are not damaged.
Any excessive vibrations during transport could cause damage to the sauna components.
DO NOT START the sauna if damage is detected! Contact your dealer or manufacturer for
troubleshooting and replacement parts.
PLEASE NOTE: The pictures and diagrams shown within this owner’s manual are
representations of this model. Actual model may vary. Design and construction are
subject to change. The sauna cannot be placed directly in the weather elements. It is
highly recommended to keep the weather elements from reaching the sauna by placing the
sauna under a covered patio or structure with a roof to fully protect the sauna.
1. Product Introduction
The steam sauna room is composed of a wood cabin. The wood cabin includes a FRONT
WALL PANEL with GLASS, REAR WALL PANEL, LEFT SIDE WALL PANEL, RIGHT SIDE
WALL PANEL, ROOF, and BENCHE(S). Other smaller wood items will also be included and
can be identified in the schematics on pages 4, 6, and 8.
2. Parts Description
A. The REAR WALL PANEL can be seen in the image below. It will have speakers
towards the bottom of the interior side of the wall panel. It will have some cord
connections at the top center. (see Figure 1)
Figure 1

10
B. The SIDE WALL PANELS are the same size. The LEFT SIDE WALL PANEL on
model GDI-7289-01 will have a vent at the top of the wall panel. The RIGHT
SIDE WALL PANEL on models GDI-7389-01 and GDI-7689-01 will have a vent
at the top of the wall panel. (see Figure 2)
VENT
LEFT SIDE WALL PANEL
CONTROL PANEL
RIGHT SIDE WALL PANEL
GDI-7289-01 GDI-7389-01/GDI-7689-01
Figure 2
C. The FRONT WALL PANEL can be seen in the images below. The FRONT
WALL PANEL will have one stationary glass panel on GDI-7289-01 and two
stationary glass panels on GDI-7389-01 & GDI-7689-01 already in place and the
glass door will be pre-installed. (see Figure 3)
GDI-7289-01 GDI-7389-01 GDI-7689-01
Figure 3

11
Assembly Instructions
A. Choose a good location to install the sauna
1. The location must be dry, leveled, and away from any source of water.
2. The stove must be installed by a certified electrician.
3. Two adults are required for installation on model GDI-7289-01 and three adults
for installation on models GDI-7389-01/GDI-7689-01.
4. Wood cabin installation order: REAR WALL PANEL RIGHT SIDE WALL
PANEL LEFT SIDE WALL PANEL FLOOR PANEL FRONT WALL
PANEL SECOND LAYER BENCH SUPPORT PANEL FIRST LAYER
BENCH SUPPORT PANEL SECOND LAYER BENCH FIRST LAYER
BENCH BACKREST ON REAR WALL PANEL BACKREST ON RIGHT
SIDE WALL PANEL FAN SHAPED BENCH RIGHT SIDE BENCH
SUPPORT PANEL RIGHT SIDE BENCH REINFORCEMENT RIGHT
SIDE BENCH ROOF PANEL
5. Tools Required: Battery Operated Screwdriver or Hand-Held Philips Screwdriver,
Rubber Mallet, Claw Hammer, Leveler, and Ladder.
B. Installing the REAR WALL PANEL and RIGHT SIDE WALL PANEL
1. Place the REAR WALL PANEL upright. Next, stand the RIGHT SIDE WALL
PANEL upright and up against the REAR WALL PANEL. Locate the screw holes
on the exterior side and screw the two wall panels together using the provided
screws. (see Figure 4 & 5)
Figure 4

12
Figure 5
C. Installing the LEFT SIDE WALL PANEL to the REAR WALL PANEL
1. Place the LEFT SIDE WALL PANEL up against the REAR WALL PANEL and follow
the same instructions used to mount the RIGHT SIDE WALL PANEL to the REAR
WALL PANEL. Make sure to use the correct size wood screws when screwing the
wall panels together. (see Figure 6 & 7)
Figure 6

13
Figure 7
D. Installing the FLOOR WOOD GRADE and FRONT WALL PANEL to the LEFT
SIDE WALL PANEL and RIGHT SIDE WALL PANEL
1. First, place the FLOOR PANEL on the inside of the sauna room and on your
floor (concrete floor is preferred). Two/three adults will be need to install the front wall
panel. Be cautious when installing the FRONT WALL PANEL with the stationary
glass panels and glass door. Stand the FRONT WALL PANEL up against the side
wall panels and use the provided wood screws to attach the FRONT WALL
PANEL. (see Figure 8)
Figure 8

14
E. Installing the SECOND LAYER BENCH SUPPORT PANEL, FIRST LAYER BENCH
SUPPORT PANEL, and FLOOR PANEL
1. Hold the SECOND LAYER BENCH SUPPORT PANEL vertically in place and install it
as seen in Figure 9 below. The SECOND LAYER BENCH SUPPORT PANEL is only
on model GDI-7689-01.
2. Next, hold the FIRST LAYER BENCH SUPPORT PANEL vertically in place and
Install it as seen in Figure 9 below. Also, place FLOOR PANEL in position as
well. Use the provided screws to secure the BENCH SUPPORT PANELS into
place. (see Figure 10)
Figure 9
Area under bench
For Model GDI-7689-01
Figure 10 For Model GDI-7289-01

15
F. Installing the SECOND LAYER BENCH and FIRST LAYER BENCH
1. Slide into position the narrow wood slats that support the SECOND LAYER
BENCH (upper bench for model GDI-7689-01 only). (see Figure 11)
2. Next, slide into position the SECOND LAYER BENCH (upper bench for models
GDI-7689-01). The screw locations are indicated with arrows for the upper and lower
benches. (see Figure 12 & 12a)(Please Note: ONLY INSTALL BENCH ALONG
REAR WALL AT THIS TIME)
3. Then slide into position the FIRST LAYER BENCH (lower). (see Figure 13 & 13a)
Figure 11
Figure 12 GDI-7689-01

16
Figure 12a
Figure 13 GDI-7289-01
Figure 13a

17
G. Installing the BACKREST ON WALL PANELS
1. Now it is time to install the BACKREST ON REAR WALL PANEL. In addition, you
will need to connect the wire connection from the REAR WALL PANEL to the wire
connection on the BACKREST ON THE REAR WALL PANEL. After connected,
tuck the wires behind the BACKREST. Use the provided screws to screw into
place. (see Figure 14 & 15) Also, you will need to connect the wire connection
from the RIGHT REAR CORNER to the wire connection on the BACKREST ON
THE RIGHT SIDE WALL PANEL (for GDI-7389-01 & GDI-7689-01). After
connected, tuck the wires behind the BACKREST. Use the provided screws to
screw into place. (see Figure 14, 15, & 16) Please note that the FAN SHAPED
BENCH has not yet been installed as seen in Figure 16. It will be installed in
Section H, Part 2.)
Rear Wall –Middle Light Connection Rear Right –Corner Light Connection
Figure 14
Figure 15

18
Figure 16
H. Installing the FAN SHAPED BENCH, RIGHT SIDE BENCH SUPPORT PANEL, RIGHT
SIDE BENCH REINFORCEMENT, and RIGHT SIDE BENCH (only on models GDI-
7389-01 and GDI-7689-01)
1. You are ready to install the FAN SHAPED BENCH, RIGHT SIDE BENCH SUPPORT
PANEL, and RIGHT SIDE BENCH REINFORCEMENT. Be sure to slide into position
the narrow wood slats that support the RIGHT SIDE BENCH as seen in Figure 17.
Use the provided screws to secure. (see Figure 18)
Figure 17

19
Figure 18
2. The RIGHT SIDE BENCH and FAN SHAPED BENCH are ready to be installed. (see
Figure 19, 20, & 21)
Figure 19 Figure 20
Figure 21

20
I. Installing the ROOF PANEL
1. Place the ROOF PANEL over the wall panels carefully. (see Figure 22)
2. Next, carefully slide the ROOF PANEL into place.
3. Use the provided screws to secure the roof into place. (see Figure 23 & 24)
Figure 22
Figure 23