GoldenDesigns MX-J206-02S User manual

Model: MX-J206-02S & MX-J306-02S
FOR CARBON MODEL SAUNAS
HEMLOCK AND RED CEDAR MODELS
FOR INDOOR USE ONLY
MX-J206-02S: 120V/15AMP DEDICATED CIRCUIT REQUIRED
MX-J306-02S: 120V/20AMP DEDICATED CIRCUIT REQUIRED

1
Thank you for your purchase of the Infrared Sauna!
Index
=====================================
Page
Important Safety Guides…………………………………………………...… 2
Introduction…………………………………………………………...………… 3
Health & Beauty Benefits……………………………………………………… 3
Highlights……………………………………………………………….……..… 4
Assembly..…………………………………….……………………………..….. 4
Operating Your Sauna..………………………………………………………… 12
Tips For Using Your Sauna...………………………….……………………….14
Safety Instructions………………………………………………………………. 15
Safeguards For Your Sauna..……………………………………………..…… 16
Troubleshooting Guide..………………………………………………………… 16
Warranty……………………………………………………………………..….. 19
Warranty Card…………………………………………….……………………… 20
WARNING: Visually inspect all heaters before assembly to make sure they are not
damaged. Any excessive vibrations during transport could cause damage to the heating
elements. DO NOT START the sauna if damage is detected! Contact your dealer or
manufacturer for troubleshooting and replacement parts.
DISCLAIMER
The infrared rays emitted by your sauna are reported to offer a wide range of possible
therapeutic benefits based on research completed over the last 25 years from all around the
world. These benefits are presented for reference purposes only and no implication of
infrared saunas creating a cure for or treating any disease is implied nor should it be inferred.
If you have a health condition, are taking prescription drugs, or have acute joint injuries,
please consult your medical physician before starting infrared therapy. Persons with
surgical implants (metal pins and rods, artificial joints, silicone, or other types of surgical
implants) typically do not experience any adverse effects, but should also consult their
physician or surgeon before starting infrared therapy. Models are subject to change without
notice. Pictures shown are for representation only and may not resemble your exact model.

2
READ IMPORTANT SAFETY GUIDES BEFORE USING!
READ AND FOLLOW ALL INSTRUCTIONS
A). Please following all warning labels and markings on the sauna room before using.
B). Do not install any receptacles on the interior or exterior walls of the sauna room.
C). No locking devices are installed or shall be installed on the door of the sauna room which
could result in entrapment within the sauna room.
D). During use, the ceiling vent can be in the opened position.
E). CAUTION! Hyperthermia Danger: the normal body temperature can't rise above 103°F.
Symptoms of excessive hyperthermia include dizziness, lethargy, drowsiness,
and fainting. The effects of excessive hyperthermia may include failure to perceive heat,
physical inability to exit sauna, unawareness of impending hazard, unconsciousness and
fetal damage in pregnant women. Hyperthermia could make your body's core temperature
rise. You should not set the temperature to an excessively high temperatures.
F). Do not use drugs, medications, or consume alcohol prior to or during the sauna session
as they may lead to unconsciousness and/or other harmful physical injuries. If
absolutely necessary, persons using medications should consult a physician before using
the sauna. Some medications may induce drowsiness while others may affect the heart
rate, blood pressure, and/or blood circulation.
G). WARNING! Your hands must be dry and free of moisture before plugging and unplugging
cords and wiring harnesses from the power supply and circuit boards. Never operate the
sauna with wet hands or wet feet to avoid risk of electric shock. Never touch the metal
prongs of the plug.
H). Persons suffering from obesity or with a medical history of heart disease, low or
high blood pressure, circulatory system problems, or diabetes should consult a
physician prior to using the sauna.
I). Do not pour water or any other liquids on the infrared emitters. Do not place
combustible materials near on or on the heaters. Do not bump, hit, or break the
heating elements as it may cause an electrical short and pose a safety risk.
J). To reduce the risk of injury, do not allow children to use the sauna unless they are closely
supervised by an adult and use of the sauna has been prescribed by a medical physician.
K). If the power supply cord becomes damaged, it must be replaced immediately by the
manufacturer or its agent. If you find the power cord is too hot or that the electrical
equipment may be experiencing technical problems, please contact the manufacturer or
its agent immediately to avoid hazardous conditions.
L). Pregnant or possibly pregnant women should contact their physician prior to using the
sauna. Excessive temperature has the potential for causing fetal damage during
pregnancy.

3
M). Never sleep inside the sauna.
N). Do not use any type of cleaning agents on the interior of the sauna. Only wipe down with
a cloth and water.
O). Do not stack or store any object on top or inside the sauna.
P). Do not use the sauna during an electrical storm to avoid risk of shock.
Q). Do not attempt to make any repairs yourself. If a problem occurs with the sauna, please
contact seller, distributor, or the manufacturer to avoid safety risks. Unauthorized repair
attempts will void the manufacturer’s warranty.
R). Please make sure the outlet power supply meets the specifications required.
Failure to meet the requirements may cause safety risks.
S). Some sauna models are equipped with reading and roof lamps. Because the
lamp temperature will become very hot once powered on, do not attempt to touch
the lamp to avoid being burned. Do not attempt to touch it for at least 20
minutes after it has been powered off.
T). Do not make any modifications to the sauna, the sauna structure, or the sauna
components.
SAVE THESE INSTRUCTIONS
Introduction
We welcome you to the most affordable infrared sauna in the nation! We also congratulate you on your new
path to better health! Thousands of users enjoy the benefits of infrared saunas every day. Infrared saunas help
you burn calories, reduce toxins, relieve pain and even clear complexions. Now you can enjoy the great benefits of
far infrared heat within the privacy of your own home.
Health & Beauty Benefits
Relieve pain: The far infrared rays of a sauna accelerate the blood circulation and supply more oxygen to the
body. Increased blood circulation diminishes inflammation, relieves pain, and speeds up recovery. Infrared saunas
have also been used to treat bursitis, rheumatism, arthritis, and hemorrhoids. Increased blood circulation not only
alleviates internal ailments, but also skin conditions such as psoriasis, eczema and scars. Good circulation is
essential for smooth and healthy skin.
Burn calories & fat: The far infrared rays of the sauna eliminate extra salt and subcutaneous fat. Burn up to
600 calories in a half hour session versus a half hour of jogging which burns 300 calories or a half hour of cycling-
which burns 225 calories.
Relax your body and mind: Use the built-in CD player to listen to your favorite music to relax and reduce
stress. Infrared saunas also improve symptoms of insomnia and other stress related disorders.
Reduce toxins and improve complexions: Perspiring in a lower temperature environment activates the
sweat glands and expels toxins and heavy metals from the body.

4
Highlights
a. High quality craftsmanship
b. Automatic thermostat for constant temperature
c. Timer and buzzer: buzzer sounds 5 minutes before the end of the sauna session
d. Digital sensor and thermometer
e. Infrared carbon heat emitter panels
f. Power supply:
Main Power: main power to sauna room
HT1, HT2, HT3, & HT4: power to heaters
Light: power to reading lamp
CTRL: power to control panel
CD/SIG: communication to MP3 Jack,
Speakers,and temperature sensor
Fuse Reset: resets the power supply
g. MP3 Jack
h. Buckles
Assembly
PLEASE NOTE: The pictures and diagrams shown within this owner’s manual are for
representation only. Actual model may vary. Please note that your sauna has been
completely assembled and tested at the factory prior to packaging. Please further note that
the rear wall panel is intentional warped as part of the overall design. Two adults will be
needed to assemble the sauna room.

5
Assembly Requirements
a. You will need a Philips screwdriver, ladder, and two adults to assemble.
b. Do not plug any other appliances into the power supply of the sauna room other than the designated sauna
connections/plugs.
c. Assemble the sauna room on a completely level surface.
d. Do not spray or get water on the exterior/interior walls of the sauna room. If the floor is damp, install a floor
separator to keep the sauna high & dry.
e. Do not store flammable objects or chemical substances near the sauna.
Sauna Room Assembly:
1. Structure of Infrared Sauna. See FIG-1
2. Make sure all parts are present before installing the unit. See packing list below.
A. Front Panel B. Floor Panel C. Back Panel D. Left Side Panel E. Right Side Panel
F. Bench G. Bench Heater Panel H. Roof Panel I. Roof Cover J. Floor Heater
K. Handle
1. Power Supply 6. Left Side Panel 1000 x 300mm 200W
2. Color Lights 7. Rear Wall Panels 1000 x 400mm 300W
3. Temperature Sensor 1000 x 400mm 300W
4. Speakers 8. Rights Side Panel 1000 x 300mm 200W
5. Control Panel 9. Bench Support Panel 18 x 570mm 300W
10. Floor Panel 1000 x 400mm 300W
FIG-1a

6
1. Power Supply 6. Left Side Panel 1000 x 400mm 300W
2. Color Lights 7. Rear Wall Panels 1000 x 400mm 300W
3. Temperature Sensor 1000 x 400mm 300W
4. Speakers 1000 x 400mm 200W
5. Control Panel 8. Right Side Panel 1000 x 400mm 300W
9. Bench Support Panel 18 x570mm 300W
10. Floor Panel 1000 x 400mm 300W
FIG-1b
4. 2-person saunas are packed into two cartons. For example: C/NO: 002 1 OF 2 and C/NO: 002 2 OF 2.
3-person sauna and 4-person saunas are packed in three cartons. For example: C/NO: 002 1 OF 3, C/NO:
002 2 OF 3, and C/NO: 002 3 OF 3. See FIG-2.1 & 2.2

7
FIG-2.1 Cartons FIG-2.2C/No.
4. Place the Floor Panel on a smooth/flat surface and make sure which side is the front and which side is the back.
The front of the floor has no stain finish as the other three sides do. See FIG 3.
FIG 3 Placing Floor Panel FIG 4 Assembling Back Panel
4. Align the Back Panel by placing it up and onto the Floor Panel. It should sit up against the quarter round trim
molding on the Floor Panel. One person should hold the Back Panel while the other person continues to the next
step. See FIG 4
5. Align the Right Side Panel by placing it up and onto the Floor Panel; make sure the Right Side Panel fits flush into
the Back Panel. See FIG 5

8
FIG 5 Assembling Right Side Panel FIG 6 Buckle
7. Latch the Right Side Panel with the Back Panel. The buckle has a guide tab that must be placed in the guide slot for
alignment. When the Back Panel and the Side Panel are attached together on the floor panel, make sure all the
buckles are latched. See Figure 6
8. Align the Left Side Panel by placing it up and onto the Floor Panel; make sure the Right Panel fits flush into the Back
Panel and latch together. See FIG 6 and FIG 7
FIG 7 Assembling Right Panel FIG 8 Placing Floor Heater

9
Bench Heating Board
9. Place the Floor Heater on the Floor Panel making sure that the Floor Heater is in front of the Bench Heater Panel
slots. Please note there is a pre-cut small hole under the Bench Heater Panel which is provided for the Floor Heater
cord. Connect the Floor Heater cord to the cord coming from the Left Side Panel. See FIG 8 & 8.1
FIG 8.1 Connect Floor Heater
10. Slide the Bench Heater Panel down (vertically) into the slot at an angle and pull it forward as seen in FIG 9. Connect
the Bench Heater Panel cord with the cord coming from the Rear Wall Panel. Next, place the Bench on top of the
Bench Heater Panel and slide it into place all the way back against the Rear Wall Panel. See FIG 9, 9a & 10 Note:
Make sure the cords are connected snug and tight, otherwise the heaters will not work.
FIG 9 Installing Bench FIG 9 Connecting Cord FIG-10 Installing Bench
11. Align the Front Panel up against the Floor Panel. Remember, this side of the Floor Panel has no stain finish. Next,
latch the Front Panel with the Left and Right Side Panels respectively. Note: Be cautious with the glass door to
avoid breakage. See FIG 11.
Floor Heater
Floor Heater Wire

10
FIG 11 Assembling Front Panel FIG 12 Installing Roof Cover
12. Place cords/wires of Side Panel and Back Panel into the sauna room area to avoid damaging the cords/wires during
the roof installation. Open the door, lift the Roof Panel up and over the sauna room, and gently lower it into place resting
it on the wall panels. See FIG 12.Make sure that all cords/wires are slipped through the corresponding holes in the
Roof Panel. Proceed in screwing the Roof Panel down. See FIG 13
.
FIG-13 Slip cords/wires through corresponding holes
13. Connect all the wires and connectors to the corresponding outlets on the Roof Panel. Please be sure all the plugs are
connected snug and tight. See FIG 14.
FIG-14 Connecting cords/wires connectors

11
Connect the plugs according to the respective labels. Connect the CTRL plug from the power supply to the CTRL plug from
the control panel. Then screw the two connections together. Last, connect the buzzer connection. See FIG 14 –FIG 18.
FIG 15 FIG 16
FIG 17 FIG 18
14. Make sure all steps are completed correctly. Plug in the power cord to your wall outlet. Turn on the sauna at
the control panel to confirm that the control panel is responding. If the control panel responds accordingly, then
proceed in putting the Roof Cover onto the Roof Panel. Make sure to pull the power cord through the
corresponding hole in the Roof Cover. See FIG 19
FIG 19 Slip the power cord through Roof Cover
15. Screw down the Roof Cover to the Roof.
16. Attach the door handle and screw into place. Screw cup-holder and magazine rack to the interior wall panel.
(Cup-holder and/or magazine rack are not available on all models.)
17. Enter the sauna and remove the protective covering from the TEMPERATURE SENSOR. Situate the
TEMPERATURE SENSOR so that it is vertical, pointing downward.

12
FIG 19
Installation Completed.
Operating the Sauna
NOTE: Before the sauna is turned on, remove plastic protective covering from the CONTROL PANELS. Please check
and confirm that the connections to the POWER SUPPLY, HEAT EMITTERS, CD/RADIO, and TEMPERATURE
SENSOR are connected properly. The power supply voltage and frequency must match the requested voltage and
frequency of the sauna (120VAC 15AMP Dedicated Circuit or 120VAC
20AMP Dedicated Circuit).
Since many materials absorb the infrared rays, minimal clothing is recommended for maximum effect. The infrared
sauna emitters are designed to heat you and not necessarily the air inside the sauna. It is not a hot box like a
traditional sauna. The temperature gauge is a guide for your safety. It is recommended that you drink water before,
during, and after sauna use to prevent dehydration since body fluids will be lost through perspiration. It is not
recommended to shower after use since the pores in your skin will be open and could possibly absorb anything in
the water.
1. Plug the sauna into the outlet receptacle.
2. Press the POWER button once. The POWER light will come on, the TIME DISPLAY will show 90 (minutes), the
TEMPERATURE DISPLAY will show 66 (degrees Celsius), and the control panel will flash.
3. Press the up/down arrows under the TIME DISPLAY to adjust the amount of time you want the sauna to remain on.
Press the C/F button to choose between Celsius and Fahrenheit. Press the up/down arrows under the
TEMPERATURE DISPLAY to adjust the temperature setting. Once you have set these adjustments to the desired
settings, press the START/WORK button. If you don’t press the button for 5 seconds, the control panel will stop
flashing and the set-up values will be memorized. The WORK and HEAT lights will now be on and the emitters will now
be generating heat. You will need to pre-heat the sauna room to the set temperature before entering. Please keep
in mind that you will increase the time it takes for the sauna room to reach the set temperature if you enter the sauna
room before it has reached the set temperature.

13
4. During your sauna session, set-up time will count down the minutes one by one. When the time remaining is 5
minutes, the buzzer will make a warning sound for approximately 15 seconds letting you know you only have 5
minutes remaining. At this point, you can let the time run out or adjust the time by pressing the up/down arrows under
the TIME DISPLAY. If you do choose to adjust the time, the control panel will flash and the emitters will stop
generating heat. Once you set the time to the desired setting, then press the START/WORK button twice and the
control panel will stop flashing and heat will began coming from the emitters once again.
5. Heating times do vary. Generally, it will take approximately twenty to thirty minutes to preheat the sauna to 50
degrees Celsius / 122 degrees Fahrenheit. When the ambient temperature is low, heating requires additional time.
For the first few times of use, you may use 46 degrees Celsius / 115 degrees Fahrenheit as a reference starting point
for a time period of about 15 minutes (this represents the actual time you are in the sauna at the desired
temperature). As you become more comfortable and familiar with the sauna, you can increase the temperature and
time period according to personal preference.
6. When the temperature is at the set-up value, the digital control will maintain the set temperature.
The WORK light will remain on and the HEAT light will turn off. The emitters will stop generating heat. Once the
inside temperature drops approximately 4 degrees, the HEAT light will turn back on and heat will again be
generated by the emitters. With the digital control, the inside temperature will always remain around the set-up
value.
7. Reading lamps and/or roof lamps and/or color therapy lamps are operated by pressing the respective buttons
located towards the center of the control panel. These lamps are offered on some models and are not available on
all models.
8. Chromotherapy/Color Therapy Lighting (optional) can be operated as follows. First, you
will need to install the battery. Once the battery has been inserted into the remote, you are ready to operate
the chromotherapy/color therapy lighting system. Press the READING LIGHT button on the sauna control panel.
The white light will come on. While pointing the remote at the ceiling light, you can press any of the colors on the
remote and that color will be displayed. You can use the SHADE button on the remote to go through a sequence
of colors. If you want to turn the light off during your sauna session, you can press the POWER button on the
remote. Please note: You must be inside the sauna room for the remote to work. Remote may vary in
appearance.

14
Power On/Off: Press to control the main power of the sauna
Power Indicator: Indicates the status of the sauna’s main power
Work Start/Stop: Press to control the working functions of the sauna
Work Indicator: Indicates the working status of the sauna
Heat Indicator: Indicates the status of heating function
Light: Press to control the lighting function
Time Display: Displays the heating time of the sauna in minutes
Time: Press to adjust the setting of the timer
Temperature Display: Displays the actual interior temperature of the sauna room in
0
C/
0
F
Temperature: Press to adjust the temperature setting
0C/0F: Press to change the temperature display between 0
C/
0
F
Pictures shown are for representation only and may not resemble your exact model.
Tips for using Your Sauna
1) If you take a hot/warm shower or bath before using your sauna, you may perspire more and experience more
comfort.
2) Drink water prior to, during, and after your sauna session to replenish body fluids.
3) To regulate the set temperature inside the sauna to your comfort level, use the movable roof ventilation or leave
the door open slightly. The roof ventilation is installed on the sauna and used based on personal preference.
4) Use 2 or 3 towels during your sauna session. Fold one of the towels several times and place it on the bench. This
towel will absorb some of your perspiration while adding comfort as you sit on the bench. Place another towel on the
floor to absorb perspiration as it falls from your body(onlyonCeramicModelSaunas). Be sure not to place any towels
over the floor heat emitters. Use a third towel to wipe perspiration from your body from time to time.
5) At the first sign of a cold or flu, increasing your sauna sessions may be beneficial in boosting your
immune system and decreasing the reproductive rate of viruses.
6) To help relieve sore and tense muscles, massage the affected areas during your sauna session.
7) To treat your ankles and feet more effectively, you can elevate them and move them close to one of the heat
emitters to achieve a deep heating effect.

15
8) To utilize the sauna's heat therapy effect, put oil or treatment into your hair and wrap it with a towel. After your
sauna session is over, rinse your hair thoroughly. Please follow the product directions for the intended benefits.
9) The peaceful and relaxed state rendered by a sauna session may help you to sleep easier and deeper.
10) To conserve energy consumption, please unplug your sauna when not in use.
11) After the sauna session is over, do not jump into the shower or bath immediately. Because your body was heated
up during the sauna session, it will continue to perspire even after the heat emitters are off. Sit in the sauna with
the door open slightly and let your body cool down. Once your body has cooled down and you feel comfortable,
you can exit the sauna. After about twenty minutes and when your body has completelycooled down, you can take
a shower to rinse the perspiration off your body.
Safety Instructions
1.) Read and follow all instructions carefully before using the sauna.
2.) When installing and using the electrical equipment, safety precautions should always be followed.
3.) To reduce the risk of injury, do not allow children to use the sauna unless they are closely supervised at all times by
an adult.
4.) Do not use the sauna immediately following strenuous exercises. Wait at least 30 minutes to allow the body to
cool down completely.
5.) Pregnant or possibly pregnant women should contact their physician prior to using the sauna. Excessive
temperature has a high potential for causing fetal damage during pregnancy.
6.) Hyperthermia Danger: the normal body temperature can't rise above 39°C (103°F). Symptoms of excessive
hyperthermia include dizziness, lethargy, drowsiness, and fainting. The effects of excessive hyperthermia may
include failure to perceive heat, physical inability to exit sauna, unawareness of impending hazard,
unconsciousness and fetal damage in pregnant women. Hyperthermia could make your body's core temperature
rise. Setting desired temperature to an excessively high temperature is not recommended.
7.) The use of alcohol, drugs, or medications prior to or during the sauna session may lead to
unconsciousness and/or other harmful physical injuries.
8.) Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure,
circulatory system problems, or diabetes should consult a physician prior to using the sauna.
9.) Persons using medications should consult a physician before using the sauna. Some medications may induce
drowsiness while others may affect the heart rate, blood pressure, and/or blood circulation.
10) Exercise care before and after sauna use.
11) Never sleep inside the sauna.
12) Do not use any type of cleaning agents on the interior of the sauna. Only wipe down with a cloth and water.
13) Do not stack or store any object on top or inside the sauna.
14) If the power supply cord becomes damaged, it must be replaced immediately by the manufacturer or its agent. If
you find the power cord is too hot or that the electrical equipment may be experiencing technical problems, please
contact the manufacturer or its agent immediately to avoid hazardous conditions.
15) Do not use the sauna during an electrical storm to avoid risk of shock.

16
16) Do not continuously switch the power on and off as it will compromise the life of the electrical components.
17) Your hands must be dry and free of moisture before plugging and unplugging cords and wiring harnesses from the
power supply and circuit boards. Never operate the sauna with wet hands or wet feet to avoid risk of electric shock.
Never touch the metal prongs of the plug.
18) Do not attempt to make any repairs yourself. If a problem occurs with the sauna, please contact seller,
distributor, or the manufacturer to avoid safety risks. Unauthorized repair attempts will void the manufacturer’s
warranty.
19) Please make sure the outlet power supply meets the specifications required. Failure to meet the
requirements may cause safety risks.
20) Some sauna models are equipped with reading and roof lamps. Because the lamp temperature will
become very hot once powered on, do not attempt to touch the lamp to avoid being burned. Do not attempt
to touch it for at least 20 minutes after it has been powered off.
21) Do not pour water or any other liquids on the infrared emitters. Do not bump, hit, or break the heating
elements as it may cause an electrical short and pose a safety risk.
22) Do not make any modifications to the sauna, the sauna structure, or the sauna components.
23) Prior to each sauna session, the sauna room is to be inspected for correct operation. If for any reason your
sauna room does not seem to be operating properly, discontinue use and contact the manufacturer.
Safeguards For Your Sauna
1. Do not install the sauna near water, near a bathtub, near a shower, in a wet basement, or near a swimming pool.
2. Do not use liquid cleaners or aerosol cleansers inside the sauna. Unplug the sauna from the wall outlet before
cleaning. Use plain water and a soft cloth for cleaning.
3. The power supply cord should be routed so that it is not walked on or pinched by any object that may be placed
against it.
4. When replacement parts are required, be sure they meet the specified requirements of the manufacturer.
Unauthorized substitutes may result in fire, electric shock, or other hazardous conditions. After any
repairs, please ask the service technician to perform safety checks to determine that your sauna is working
properly.
5. Do not use any wall receptacle adapter or extension cord between the sauna cord and wall receptacle.
Troubleshooting Guide
1. No Heat Coming From Some Of The Heat Emitters
Solution: Check to make sure all the heat emitter cords are properly connected, including the cord to the heat
emitter underneath the bench (if applicable). Go to the roof, and also check that the heat emitter cords are

17
properly connected to the cords on the roof and that those cords are properly plugged into the power supply.
Solution: If some of the heat emitters are working, then the ones which are not working may have been
damaged. Do not continue to operate. Contact the manufacturer for
replacement parts.
Solution: If the heat emitters are not working but the control panel displays the time and temperature, then the
temperature sensor may not be plugged in properly or it may be damaged. Turn the control panel off and then
go to the roof of the sauna and locate the red and black wires near the air vent towards the rear of the sauna.
After you have located the red and black wires labeled “TEMP SENSOR”, disconnect them. Connect the spare
temperature sensor. For testing purposes, insert the “TEMP SENSOR” (you just connected) down the vent on
the roof so that it is now inside the sauna. Then go to the control panel and press the power button. If the heat
emitters now have heat, then the “TEMP SENSOR” was the cause of the problem. You may have to wait about
five minutes to
confirm if the heat emitters are generating heat. Remove the original temperature sensor from its hole and
replace it with the spare one.
2. Control Panel Malfunctioning
Solution: The control panel will turn on, but not off and the displayed numbers flash. The issue may be a
connection problem. Go up to the roof and locate the “CTRL” wire harness you connected when the roof
was installed onto the sauna room. Disconnect the “CTRL” wire harness, check the pins to make sure they
are straight and not bent, and firmly reconnect the “CTRL” wire harness. Attempt to turn the sauna on at
the control panel and check to see if the buttons are now responding. Contact the manufacturer for any
additional troubleshooting.
Solution: The control panel will not turn off, the power/work/or heat lights do not come on, or the
temperature and timer buttons do not work means the control panel may have been damaged and will need
to be replaced. Contact the manufacturer for additional troubleshooting.
3. Sauna Shows Signs Of No Power
Solution: There could be one of a few problems causing this. First, check to see if the cord from the power
supply is plugged into the wall outlet. Also check your main circuit breaker to confirm that it has not tripped.
Check the power supply on the roof of the sauna to make sure there are no signs of malfunctioning, such as a
high temperature, burning odor, or strange sounds. Also, check to make sure none of the power cords are
damaged. If the power supply is malfunctioning or power cords are damaged, then unplug the sauna
immediately and contact the manufacturer.
Solution: If your sauna is plugged in and you have no power at the control panel, then the power
supply may need to be reset. Go to the roof of the sauna and locate the power supply. Press the

18
RESET button to reset the power supply. The RESET button is on the same side of the power supply
as all the heater cord connections. Attempt to turn the sauna on at the control panel. Contact
the manufacturer for any additional troubleshooting.
Solution: There could be damage to the temperature sensor. If your sauna arrived with a spare temperature
sensor, turn the control panel off and go to the roof of the sauna and locate the red and black wire near the air
vent towards the rear of the sauna. After you have located the red and black wires labeled “TEMP SENSOR”,
disconnect them. Connect the spare temperature sensor. For testing purposes, insert the “TEMP SENSOR”
(you just connected) down the vent on the roof so that it is now inside the sauna. Then go to the control panel and
press the power button. If the heat emitters now heat, then the temperature sensor was the cause of the
problem. You may have to wait about five minutes to confirm if the heat emitters are generating heat. Remove the
original temperature
sensor from its hole and replace it with the spare one.
Solution: Check the wiring harnesses coming from the power supply located on the roof of the sauna. Make sure
the wiring harness labeled “CTRL” is connected to the power supply at one end and connected to another wiring
harness labeled “CTRL” at the other end. If this wiring harness is not properly connected, then the sauna will
show signs of having no power.

19
Limited Lifetime Warranty
5 Year Limited Warranty: Golden Designs, Inc. warranties the wood, structure, heating elements, and electronics
against defects in material and workmanship for a period of 1 to 5 years from the original date of purchase. This sauna
is for INDOOR use only. Placing your sauna outdoors will VOID this warranty. Any damage due to exposure to
outdoor elements such as rain, snow, sun, wind or extreme temperatures will not be covered by this warranty.
Any damages as a result of modifications made to the sauna or its components will void this warranty.
Extent of Warranty: This limited warranty applies to products manufactured or distributed by Golden Designs, Inc.
under the Dynamic brand name, delivered in the continental United States or Canada and extends to the original
purchaser at the original site of installation only. This warranty becomes valid at time of purchase and terminates either
by specified time frame listed above, owner transfer, or relocation. Your sales receipt showing the date of purchase
of the product is your proof of purchase.
Manufacturer Warranty
All Golden Designs, Inc. products are manufactured with the highest quality appliances and are warranted to be free
from defects in material and workmanship at the time of delivery. The appliance warranty is extended through the
manufacturer for the product including, but not limited to: stereos, CD/DVD players, etc. All exchanged parts and
products replaced under this warranty will become the property of Golden Designs, Inc. Golden Designs, Inc. reserves
the right to change manufactures of any part to cover any existing warranty. Any parts determined to be defective must
be returned to Golden Designs, Inc. to obtain warranty service. You must prepay any shipping charges, export taxes,
custom duties and taxes, or any other charges associated with the transportation of the parts. In addition you are
responsible for insuring any parts shipped or returned. You must present Golden Designs, Inc. with proof of purchase
documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof of purchase
documents will be cause to VOID this limited warranty. Products on which the serial number has been defaced or
removed is not eligible for warranty service.
Warranty Limitations
This warranty does not apply if the unit has been subject to negligence, alteration, modification, misuse, abuse, repairs
by non-Golden Designs, Inc. authorized personnel, inappropriate installations, or any case beyond the control of Golden
Designs, Inc. invalidating this warranty including but are not limited to:
Use of lacquer or paints
Sauna and other Golden Designs, Inc. products accessories placed on non-approved surfaces
Outdoor applications
Normal wear and tear or weathering
Use of product not in accordance with instructions