GoldenDesigns GDI-7289-01 User manual

GDI-7289-01 / GDI-7289-01L / GDI-7689-01 / GDI-7689-01L
2-3 and 4-6 Person Saunas
OWNER’S MANUAL
FOR STEAM MODEL SAUNAS
240VAC 40 AMP DEDICATED CIRCUIT PLUS 120VAC 15 AMP CIRCUIT
Please Note: Model numbers with “L” indicate stone on the rear wall panel and
step-down lighted ceiling. Model designs are subject to change. Steam heater
must be installed by a certified electrician.

2
Thank you for the purchase of your new Steam Sauna!
FOLLOW ALL INSTRUCTIONS AND BE CAUTIOUS OF SAFETY SYMBOLS
High Voltage Symbol: Be cautious as there is the presence of a high voltage current that flows through the equipment!
General Caution Symbol: Be cautious as the equipment uses electrical current that can cause serious injury.
1. Please read this Operating Instruction Manual thoroughly before use. This will allow the user to become familiar
with the operation of the control system. Please keep the Operating Instruction Manual available for future
reference. If any technical assistance or repairing is needed, please contact the manufacturer.
2. The steam sauna must be installed indoors or can be installed outdoors within the protection of a structure that
includes a water-proof roof protecting it from the outdoor weather elements. When not in use and placed
outdoors, a water proof cover must be used to cover the sauna room.
3. To reduce the risk of electric shock and/or fire, do not expose the control system to direct water
contact or rain. Do not open the cover to the control system as there are high tension fittings that can be
dangerous. Only dealer authorized qualified technicians should make any needed or necessary repairs at any
time.
4. Any repairs, alterations, or modifications to the control system are not authorized unless by an
approved repair technician. Any non-authorized repairs, alterations, or modifications can lead to
serious injuries and can cause the unit to work outside its intended specifications parameters.
5. Any non-authorized repairs, alterations, or modifications will void the warranty.
6. Before connecting the unit to a power source, please make sure that all wires, cords, and connections are
connected properly.
7. Make sure that the control system is in a well-ventilated and dry area. Do not place it next to any heat source, in
direct sunlight, where there is any type of vibration, or in any damp or dusty environment. It should not be place
in an area with other thermal-radiating objects.
8. When the equipment is not going to be used for an extended period of time, unplug the unit from the power
source.
9. Allow 30 seconds between turning the control system “On” and “Off”. By allowing 30 seconds between powering
the control system “On” and “Off” will prolong the life of the unit.
10.Confirm that you adhere to the correct power requirements of the control system. Connecting the control
system to other than the required voltage can damage the control system and possibly cause serious injury. It is
very important that the load parameters are consistent with that needed by the control system.
11. Canadian Red Cedar and its rich aroma can cause an extremely small percentage of the population to have an
adverse reaction known as Multiple Chemical Sensitivity (MCS). While this is not an universally recognized
disorder in the medical field, certain consumers have an adverse physical reaction to low levels of many common
chemicals and cannot tolerate any aromatic oils, shampoos with perfumes infused or certain herbs with natural
aromas. However, for the majority of the population, Canadian Red Cedar is the sauna wood of choice.

3
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOURGHLY BEFORE ASSEMBLY
GDI-7289-01L
*The above assembly diagram is for a quick
reference visual guide
only. All sauna models are not shown. The wooden box for the steam
stove has been removed from models with limited space. Parts and
accessories may vary and not always be included.

4
GDI-7289-01L Schematics
Wood Screws Machine Screws
3.5x40mm
3.5x40mm
6x50mm 6x60mm
*The above assembly diagram is for a quick
reference visual guide
only. All sauna models are not shown. The wooden box for the steam
stove has been removed from models with limited space. Parts and
accessories may vary and not always be included.

5
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOURGHLY BEFORE ASSEMBLY
GDI-7689-01L
*The above assembly diagram is for a quick
reference visual guide
only. All sauna models are not shown. Parts and accessories may vary.

6
GDI-7689-01L Schematics
Wood Screws Machine Screws
3.5x40mm
3.5x40mm
5x50mm 6x60mm
*The above assembly diagram is for a quick
reference visual guide
only. All sauna models are not shown. Parts and accessories may vary.

7
TABLE OF CONTENTS
Product Introduction 7
Parts Description 8
Assembly Instructions 9
Control Panel Operation 26
Tips for Using Your Sauna 28
Safety Instructions 28
Safeguards for Your Sauna 30
Warranty 31
Warranty Card 33
WARNING: Visually inspect all parts before assembly to make sure they are not damaged.
Any excessive vibrations during transport could cause damage to the sauna components.
DO NOT START the sauna if damage is detected! Contact your dealer or manufacturer for
troubleshooting and replacement parts.
1. Product Introduction
The steam sauna room is composed of a wood cabin. The wood cabin includes a FRONT WALL PANEL
with GLASS, REAR WALL PANEL, LEFT SIDE WALL PANEL, RIGHT SIDE WALL PANEL, ROOF, and
BENCHES. Other smaller wood items will also be included and can be identified in the schematics on page
4.
SCREW IDENTIFICATION AND LOCATION CHART:
MODELS: GDI-7289-01 & GDI-7289-01L MODEL: GDI-7689-01
MODEL: GDI-7689-01L
NOTE: The pictures and diagrams shown within this owner’s manual are representations of
this model. Actual model may vary. Design and Construction are subject to change.

8
2. Parts Description
A. The REAR WALL PANEL can be seen in the image below. It will have speakers towards the
bottom of the interior side of the wall panel. It will have some cord connection at the top center.
(see Figure 1)
Figure 1
B. The SIDE WALL PANELS are the same size. The LEFT SIDE WALL PANEL on models GDI-
7689-01 and GDI-7689-01L will have a vent. The RIGHT SIDE WALL PANEL on models GDI-
7289-01 and GDI-7289-01L will have a vent. (see Figure 2)
LEFT SIDE WALL PANEL RIGHT SIDE WALL PANEL
VENT
Figure 2

9
C. The FRONT WALL PANEL can be seen in the image below. The FRONT WALL PANEL will
have the two stationary glass panels already in place and the glass door will be pre-installed.
(see Figure 3)
Figure 3
Assembly Instructions
A. Choose a good location to install the sauna
1. The location must be dry, leveled, and away from any source of water
2. MAIN POWER cord must be easily accessible
3. Two adults are required for installation on models GDI-7289-01/GDI-7289-01L and three adults
for installation on models GDI-7689-01/GDI/7689-01L.
4. Wood cabin installation order: REAR WALL PANEL RIGHT SIDE WALL PANEL LEFT
SIDE WALL PANEL SECOND LAYER BENCH SUPPORT PANEL FIRST LAYER
BENCH SUPPORT PANEL FLOOR PANEL SECOND LAYER BENCH FAN SHAPED
BENCH FIRST LAYER BENCH BACKREST ON REAR WALL PANEL BACKREST
ON RIGHT SIDE WALL PANEL RIGHT SIDE BENCH SUPPORT PANEL RIGHT SIDE
BENCH REINFORCEMENT RIGHT SIDE BENCH FRONT WALL PANEL ROOF
PANEL
5. Tools Required: Battery Operated Screwdriver or Hand-Held Philips Screwdriver and Ladder

10
B. Installing the REAR WALL PANEL and RIGHT SIDE WALL PANEL
1. For model GDI-7689-01L, please continue to follow these instructions. For all other
models, please proceed to 1a. Place the REAR WALL PANEL and RIGHT SIDE WALL
PANEL upright and next to each other. The small wood block on the RIGHT SIDE WALL
PANEL will need to fit into place on the interior side of the REAR WALL PANEL. First, screw
in the exterior top and bottom 6x60mm machine screws only. Next, align the interior wood
block to the REAR WALL PANEL and use the two 5x50mm wood screws to mount the REAR
WALL PANEL to the RIGHT SIDE WALL PANEL. Finally, use (on the exterior side) the
remaining two 6x60mm machine screws to mount the REAR WALL PANEL to the RIGHT
SIDE WALL PANEL. (see Figure 4a and Figure 5)
1a. For models GDI-7289-01, GDI-7289-01L and GDI-7689-01, please continue to follow
these instructions. Place the REAR WALL PANEL upright. Next, stand the RIGHT SIDE
WALL PANEL upright and up against the REAR WALL PANEL. Locate the screw holes on the
exterior side and screw the two wall panels together using the 6x60mm screws.(see Figure 4
and Figure 5)
Figure 4
Figure 4a
Figure 5

11
C. Installing the LEFT SIDE WALL PANEL to the REAR WALL PANEL
1. Place the LEFT SIDE WALL PANEL up against the REAR WALL PANEL and follow the same
instructions used to mount the RIGHT SIDE WALL PANEL to the REAR WALL PANEL.
Make sure to use the correct size wood screws when screwing the wall panels together. (see
Figure 6 & 7)
Figure 6
Figure 7

12
D. Installing the FLOOR HEATER and FRONT WALL PANEL to the LEFT SIDE WALL PANEL and
RIGHT SIDE WALL PANEL
1. First, place the FLOOR HEATER on the inside of the sauna room and on your floor (concrete
floor is preferred). Three adults will be need to install the front wall panel. Be cautious when
installing the FRONT WALL PANEL with the stationary glass panels and glass door. Stand the
FRONT WALL PANEL up against the side wall panels and use the 6x50mm machine screws to
Attach the FRONT WALL PANEL. (see Figure 8)
Figure 8

13
E. Installing the SECOND LAYER BENCH SUPPORT PANEL, FIRST LAYER BENCH SUPPORT
PANEL, and FLOOR PANEL
1. Hold the SECOND LAYER BENCH SUPPORT PANEL vertically in place and install it as seen
in Figure 9 below. The SECOND LAYER BENCH SUPPORT PANEL is only on models GDI-
7689-01 and GDI-7689-01L.
2. Next, hold the FIRST LAYER BENCH SUPPORT PANEL vertically in place and install
it as seen in Figure 9 below. Also, place FLOOR PANEL in position as well. Use the
3.5x40mm screws to secure the BENCH SUPPORT PANELS into place. (see Figure 10)
Figure 9
Area under bench
For Model GDI-7689-01 and GDI-7689-01L
Figure 10
For Model GDI-7289-01 and GDI-7289-01L

14
F. Installing the SECOND LAYER BENCH and FIRST LAYER BENCH
1. Slide into position the narrow wood slats that support the SECOND LAYER BENCH (upper
bench for models GDI-7689-01 and GDI-7689-01L). (see Figure 11)
2. Next, slide into position the SECOND LAYER BENCH (upper bench for models GDI-7689-01
and GDI-7689-01L)). The screw locations are indicated with arrows for the upper and lower
benches. (see Figure 12 & Figure 12a)(Please Note: ONLY INSTALL BENCH ALONG REAR
WALL AT THIS TIME)
3. Then slide into position the FIRST LAYER BENCH (lower). (see Figure 13)
Figure 11
Figure 12

15
Figure 12a
Figure 13

16
Figure 13a
G. Installing the BACKREST ON WALL PANELS
1. Now it is time to install the BACKREST ON REAR WALL PANEL. In addition, you will need to
connect the wire connection from the REAR WALL PANEL to the wire connection on the
BACKREST ON REAR WALL PANEL (only on models GDI-7289-01L and GDI-7689-01L).
After connected, tuck the wires behind the BACKREST. Use the 3.5x40mm screws to screw
into place (see Figure 14 and Figure 15)
Figure 14

17
Figure 15
2. It is time to install the BACKREST ON RIGHT SIDE WALL PANEL. You will need to connect the
wire connections from the SIDE WALL PANEL to the wire connection on the BACKREST ON
THE SIDE WALL (only on model GDI-7689-01L). After connected, tuck the wires behind the
BACKREST. Use the 3.5x40mm screws to screw into place (see Figure 16, 17, and 18)
(Please note that the FAN SHAPED BENCH has not yet been installed as seen in
figure 16. It will be installed in Section H, Part 2.)
Figure 16
Figure 17

18
Figure 18

19
H. Installing the FAN SHAPED BENCH, RIGHT SIDE BENCH SUPPORT PANEL, RIGHT SIDE BENCH
REINFORCEMENT, and RIGHT SIDE BENCH (only on models GDI-7689-01 and GDI-7689-01L)
1. You are ready to install the FAN SHAPED BENCH, RIGHT SIDE BENCH SUPPORT PANEL, and
RIGHT SIDE BENCH REINFORCEMENT. Be sure to slide into position the narrow wood slats
that support the RIGHT SIDE BENCH as seen in Figure 21. Use the 3.5x40mm screws to
secure. Please see Figures 19, 20, and 21below.
Figure 19

20
Figure 20
Figure 21