Goldwing PITTS 30CC V3 User manual

PITTS 30CC V3
ASSEMBLY MANUAL
WWW.GOLDWINGRC.COM

01
Thank you for purchasing this excellent almost-ready to fly R/C model!!! This ARF adopts the
latest 3Ddesign features and emphasizes high performance,light weight and fun.This plane is
designed by professional engineers and built by skilled craftsmen.Many of the parts are already
pre-installed for you! We wish you great success in the assembly and flying of your new model.
Features:
1. Latest structure
2. Super quality
3. Easy installation
4. Carbon fiber wing tube
5. Carbon fiber tail wheel assembly
6. Two pieces removable wings
7. Extra strength epoxy control horns
8. Latest nylon bolts for wings installation
9. One piece carbon fiber landing gear
10.Advanced rubber wheels
11.Long servo arms included
12.Servo extension safety connector clips also included
13.Scale canopy and latest nylon bolts
14. Fixed ring inside cowling for easy build
16. Pre-hinged wing control surfaces ready to fly
17. Pre-mounted and plumbed gasoline tank ready to fly
18. Genuine ORACOVER film
19.Low wing loading makes it easy to fly
20.Light weight construction with high structural strength
21.Excellent aerobatics and 3D performance
15.One piecel stab
INTRODUCTION
61” ( 1 5 5 0mm)
63” ( 1 6 0 4mm)
132 7 s q . in(8 5 . 6 s q.dm . )
Win g Sp an:
Le n gth :
Wing Area:
PIT T S
F l y i n g
we i ght 4300-4900g

Attention
1.You should not regard this plane as toy!
2.Before the assembly please the careful reading instruction booklet, he can give
you the full detail instruction if you are the first contact airplane model public
figure, should assemble under the experienced correct instruction!
3.Please inspect in the packing all components, if lacks perhaps the damage,
please immediately with dealer relation.
4.As a result of weather temperature the moist change, the model outer covering
possibly can appear the phenomenon which relaxes, you may use the package to
have a cotton fabric the iron to burn again the outer covering smoothly, but must
take care not to apply too much heat to one area for long periods of time.
5.Inventory and inspect all parts and hardware for any imperfections or damage.
Contact us quickly if there are missing or damaged parts.
6.Fly only in AMA (Academy of Model Aeronautics) approved areas.
7.The manufacturer can not control the assembly, operation and maintenance of
this product therefore, We are not responsible for any damage that occurs as a
result of the use or misuse of this radio controlled model.
8.All GOLDWING products are guaranteed against defects within 30 days of
receiving your airplane. This warranty is limited to construction or production
defects in both material and workmanship. It does not cover any components or
parts damaged by misuse or modification.
9.The purchaser accepts all responsibility of any and all structural or mechanical
failures.
10.GoldWingRC reserves the right to make changes and amendments to
construction manuals, terms and conditions without notice.
02
If you have any problems and questions please contact GoldwingRC:
Address: No.19, Western Jinfeng Rd, Jinding science and technology
Zone, Zhuhai ,China
Postcode:519028
Tel:[phone]
Fax:[phone]
Info email: [e-mail] [e-mail]
1642378762 qq.com@
[e-mail]

03
Introduction -------------------------------------------------- -- -----
Attention------------------------------------------------------------------------
Wing Assembly-----------------------------------------------------------------
Aileron Control Horns --------------------------------------------------------
Aileron Servo Installation ----------------------------------------------------
Elevator Assembly -------------------------------------------------------------
Stab and Elevator Installation ------------------------------------------------
Elevator Servo Installation --------------------------------------------------
Rudder Assembly --------------------------------------------------------------
Rudder Horns and Hinges ----------------------------------------------------
Rudder Servo Installation -----------------------------------------------------
Tail Wheel Installation --------------------------------------------------------
Fin And Stab Cable Tensioning --------------------------------------------
Main Landing Gear Assembly -----------------------------------------------
Landing Gear Installation ----------------------------------------------------
Pants Installation --------------------------------------------------------------
Engine Installation ------------------------------------------------------------
Firewall Holes Assembly ------------------------------------------------------
Throttle Servo Installtion ----------------------------------------------------
Fuel Tank and Fuel Line assembly -------------------------------------------
Ignition Module and Battery assembly ---------------------------------------
Cowl Assembly -----------------------------------------------------------------
Wing Final assembly ----------------------------------------------------------
Canopy assembly --------------------------------------------------------------
Flight Preparation-------------------------------------------------------------
C.G Location--------------------------------------------------------------------
Symmetry Control --------------------------------------------------------------
Control Throws ----------------------------------------------------------------
Engine Debugging -------------------------------------------------------------
Flight Checking----------------------------------------------------------------
Accessories List ---------------------------------------------------------------
----- ------ 01
02
04
04
05
07
08
10
11
12
13
15
17
18
18
19
19
20
21
22
23
24
26
27
28
28
28
29
29
29
30
34
41
TABLE OF CONTENTS

04
1.Scuff the horns with sand paper to ensure a good glue bond.Drill 2.5mm
holes in the horns and install the M2.5mm ball link with the screw.
3.Apply 30 minute epoxy inside the
pre-cut slots and coat the horns with
epoxy , Insert them into the pre-cut
slots. Wipe away excess glue with
rubbing alcohol.
2
Aileron Control Horns
3
Wing Assembly
2.Pre-hinged control surface is
ready to fly.Remove the covering
below to expose the pre-cut slots with a
knife. .
2.5mm bit
21
.
12
.
21
.
11
.

05
Aileron Servo Installation
2.The covering of the servo location
had been remove as shown.Put the end
of the servo extension in the servo
location.And then pull the extension
le a d th r oug h t o th e r o ot o f t h e
wing.Taping servo lead to the inside
of the wing panel will help to
prevent lead from dropping back
inside of wing panel during
transportation.
1.Use the provided safety clips to
secure the servo and servo extension
leads.
3.Drill 1 m m h o l es f o r the se r v o
mounting screws. Position the servo
with the servo label closest to the wing
trailing edge.
4.Use a drop of thick CA glue on each
screws to prevent tapping screws from
loosening due to vibration. Install
servo with M2*12mm tapping screws.
Minimum Required Servo:180 in.oz / Metal Gear / Digital
1
2
Tape
3
Close to the
wing trailing
1mm bit
44
CA glue

06
Repeat all the previous steps for the other wing.
6 A till
position. And then install the pushrod to the arm with M2.5*16mm hex
socket screw and lock nut.
.djust the pushrod length the aileron and servo are in the neutral
2.5mm latest nylon
ball link assembly
Anodized
AL
Long servo arm
6
M2.5*60mm
Black steel
pushrod
Pre-adjustable
Epoxy horns
5
5 . Mo u n t t h e s er vo a rm a n d t he
extension arm with M2*8mm screws
and locking nuts as shown.Then turn on
the transmitter and plug the servo into
receiver. Ensure the channel is neutral.
Install the servo arm facing toward the
wing tip.Position the servo arm 90
degrees to the servo.
Upper Wing Installation
7.Apply 30 minute epoxy inside the wing pre-cut slot and coat the wing
batten with epoxy , Insert the batten into the pre-cut slots.
1
.
72
.
21
.
71
.

Elevator Assembly
07
10.Stick them with the tape till the
epoxy dry.
8
9
10
8.Apply 30 minute epoxy inside the
other wing pre-cut slot and coat the
wing batten with epoxy , Insert it into
the pre-cut slot.
9. Coat the wing rib with epoxy ,put
the wing together.Wipe away
excess glue with rubbing alcohol.

4.Remove the covering below to expose the pre-cut slots with a knife. Scuff
the horns with sand paper to ensure a good glue bond.
1.Insert the stab into the fuselage
tail. Measure the stab to find the
middle.
3.Coat the horns with epoxy. Insert them into the fuselage again.Make sure
the stab is symmerical.
08
21
1
21
.
42
.
21
.
41
.
2.Mark the stab with a pen when the stab is symmerical.Trace around
the fuselage with a knife and remove the covering below to expose the
board.Take care not to scratch the board.
21
.
31
.
21
.
21
.21
.
22
.
21
.
32
.
Stab and Elevator Installtion

7.Insert the into the
hinge-holes.
.
hinge stab
Use a drop of thick CA
glue to stick the stab and elevator
6 hinge
Stick the hinge to the
elevator first
.Insert the into the elevator
hinge-holes.
.
8.
deflection before fasten the stab
with tape.
Check you have full elevator
5.Install the two horns with M3*16mm screw and locking nut. Apply 30
minute epoxy inside the pre-cut slots and coat the horns with epoxy, Insert
them into the pre-cut slots.
21
.
8
21
.
51
.21
.
52
.
21
7
21
.
6
09