golmar iPlus EL632/IP User manual

TEL632/IP EN REV1706 X7
EL632/IP VIDEO MODULE
INSTRUCTIONS MANUAL

INTRODUCTION
CONTENTS
2
SAFETY PRECAUTIONS
Introduction...............................................................................................................................................2
Contents...................................................................................................................................................2
Safety precautions..........................................................................................................................2
EL632/IP, description of the module..................................................................................................3
Descrition of the buttons modules EL610D & EL606D........................................................................3
Door lock connection.................................................................................................................................4
Embedding box installation................................................................................................................4
Push buttons modules conection..............................................................................4
Push buttons module setting.....................................................................................................5
Installation diagrams............................................................................................................................6
Specifications and cautions..................................................................................................................7
EL632/IP VIDEO MODULE
First and foremost we would like to thank you for purchasing this product.
Our commitment to satisfying our customers can be seen from our ISO-9001 certification and from the
manufacturing of products like this one.
Its advanced technology and exacting quality control will ensure that customers and users enjoy the many
features this system offers. To obtain the maximum benefit from these features and a properly wired
installation, we kindly recommend that you spend a few minutes of your time reading this manual.
- Do not use excessive force when tightening the monitor's connection block screws.
.- Always disconnect the power supply before making modifications to the equipment.
.- The installation and handling of these devices must be carried out by authorised personnel.
.- All of the wiring must run at least 40cm away from any other wiring.
.- Install the monitor in a dry and protected place without risk of drip or water projections.
.- Do not place in humid, dusty or smoky locations, or near sources of heat.
.- Before connecting the system to the mains, check the connections between the door panel, power supplies,
switches and monitors.
.- Always follow the instructions contained in this manual.

DESCRIPCIÓN GENERAL
3
EL632/IP VIDEO MODULE
people with impaired hearing).
Note:See installation diagrams for wiring.
Micr .ophone
Speaker.
Front side.
Sound module push buttons (x2).
Relays terminals CN1.
Push buttons connector
Back side.
: ontact . Rel 3."C" c free for lock release ay
: . Rel 3."N.O" contact free for lock release ay
: Positiv , .e ground
: .Digital communication
Color camera .
R1
R1
R2,
R2
_
Leds (visual indications for
Leds illumination
Push button number.
lug the push buttons with the short
P
connection cable.
Between push buttons modules EL610D of the same embedding box,
insert the short connection cable of the low connector of the first push
buttons module to the top connector of the second push buttons
module, as shown in the drawing.
Insert the short connection cable that it is supplied with the product
EL610D, in the push buttons connector of the sound module and the
other end of the connection cable in the connector placed in the top
part of the push buttons EL610D module, as shown in the drawing.
Between push buttons modules EL610D of different embeddingt boxes,
insert the short connection cable in the low connector of the last
module EL610D of the first embedding box and the other end of the
connection cable in the middle connector of the last push buttons
module EL610D placed in the low part of the second embedding box,
as shown in the drawing.
Front side.
Push buttons module (x10).
Configuration dip switch
(Push buttons call code).
Push button number.
Input/Output push buttons connector (x3).
Back side.

DOOR LOCK CONNECTION
Installation of the embedding box:
R1 and R2 are dry contact relays to drive ac or dc locks.
4
CV-24
CV-24
Rj45 R2 R2 R1 R1
CV-24/DC
CV-24/DC
230 0
RF-12/1,25A
~ ~ 230 0
TF-104
Rj45 R2 R2 R1 R1
1650
1850
1450
PANEL INSTALLATION
EL632/IP VIDEO MODULE
Pass the wiring through the hole made in the bottom part of the
embedding box. Level and flush the embedding box. Once
the embedding box is placed, remove the protective labels
from the attaching door panel holes.
90CS
CEA90C
99
143
40
Door panel
Model
An
Al
P
90C
CEV90C
99
250
56
90
CEV90
99 mm.
328 mm.
56 mm.
The upper part of the door panel should be placed at 1,65m. height roughly. The hole dimensions
will depend on the type of door panel.
The door panel has been designed to be placed under most of the environmental conditions.
However it's recommended to take additional cautions like rainproof covers. To obtain a good
quality picture on video door entry systems, avoid direct incidence from light sources.

PUSH BUTTONS MODULES CONFIGURATION
Setting the push buttons codes
5
In case more than 2 push buttons are required, EL610D or EL606D can be added to extend the number of
push buttons.
Depending on the setting of the dip switches(*), the buttons will take different codes. .
EL632/IP allows the iomplementation up to 72 push buttons, when usfin double button configuration, or 36
buttons when using single button configuration
*
( )
2
Dip1
1
4
6
3
5
7
Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 P1
1
21
41
61
11
31
51
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
On
On
On
On
On
On
On
Push button code
2
22
42
62
12
32
52
3
23
43
63
13
33
53
4
24
44
64
14
34
54
5
25
45
65
15
35
55
6
26
46
66
16
36
56
7
27
47
67
17
37
57
8
28
48
68
18
38
58
9
29
49
69
19
39
59
10
30
50
70
20
40
60
Dip switch
P2 P3 P4 P5 P6 P7 P8 P9 P10
Dip switch configuration
Note: The built-in butons at EL632/IP are factory set as codes 101 (left) and 102 (right).
Double button configuration
EL-606D push buttons module
EL-610D push buttons module
2
Dip1
1
4
6
3
5
7
Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 P1
1
21
41
61
11
31
51
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
On
On
On
On
On
On
On
2
22
42
62
12
32
52
3
23
43
63
13
33
53
4
24
44
64
14
34
54
5
25
45
65
15
35
55
P2 P3 P4 P5
EL632/IP VIDEO MODULE
Single button configuration
EL-606D push buttons module
EL-610D push buttons module
Push button code
Dip switch
Dip switch configuration
Note: The built-in buton at EL632/IP is factory set as codes 102 (right).

GENERAL INSTALLATION SCHEMA
6
EL632/IP VIDEO MODULE
P-switch
T-switch
T-switch
T-switch
T-switch
T-switch
T-switch
T-switch
PoE-switch
UTP Cat5/6
UTP Cat5/6
Beoview7 Beoview7
EL632/IP (*)
EL610D (*)
*For detailed information on the conection of the door lock and EL610D, check pages 3 and 4.

Especificaciones, precauciones y mantenimiento
7
!Material / ColoUr Grey plastics
!Installation Nexa panel
!Dimensions 83(W) x 100(H) x 39(D) mm
!Weight 160 gr.
!
!Sensor 1/4"
!Resolution VGA(640x480)
!Ilumination 0 Lux, (white leds lighting)
!Optics 2,6mm
!Viewing angle 127º
!
!Leds technology SMD
!Number of light leds 8
!Numbner of leds for signalization 4
!Working temperature -20 to +60ºC
!Humidity 10%~90% non-condensing
!Communication Hands free
!Volume adjustment By configuration software
!Audio power 1 Watt
!Maximum distance to Switch 90 meters
!power source POE 48VDC ( IEEE 800.3af)
!Consumtion 2w idle.
SPECIFICATIONS
EL632/IP VIDEO MODULE
Cautions
Maintenance
This is a product manufactured with high quality materials. Do not use chemical products or abrasives or
cleaning agents.
This is an electronic product, please consider the following cautions.
- Do not through liquids over the unit. Any liquid entering into the product may cause a failure and there
is a risk of fire.
- Do not use the monitor under high temperatures, corrosive environments or high humidity grades
above its specifications.
- Do not hang neither place any object on it. The bracket might brake, as it is designed to suport its own
weight. Pulling, pushing or climbing on it may cause the monitor to fall.
- This is a professional product. it is strongly recommended to follow the instalaltion specifications and to
leave the installation to a profesional installer.

[e-mail]
www.golmar.es
Sistemas de comunicación S.A.
Golmar se reserva el derecho a cualquier modificación sin previo aviso.
Golmar se réserve le droit de toute modification sans préavis.
Golmar reserves the right to make any modifications without prior notice.
GOLMAR S.A.
C/ Silici, 13
08940- Cornellá de Llobregat
SPAIN