golmar G2+ User manual

G2+ 2-wire installation
USER MANUAL
Kit Soul
Art monitor7 Lite
TECHNOLOGY
Cód. 50122676 TS5110 ART 7 LITE EN REV.0220

SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE 2
CONTENTS
Contents ....................................................................................................................................................................2
Recommendations.....................................................................................................................................................3
System operation .......................................................................................................................................................3
FA-G2+/ power supplyLITE ........................................................................................................................................4
Description ......................................................................................................................................................4
Installation .......................................................................................................................................................4
Soul panel- /LITE ................................................................................................................................................5 to 77
Description ......................................................................................................................................................5
Installation .......................................................................................................................................................6
Installation terminals ........................................................................................................................................6
Configuration switches.....................................................................................................................................7
Setting the audio level ......................................................................................................................................7
Art /G2+ monitor ...................................................................................................................................... to 27 LITE 8 0
Description ......................................................................................................................................................8
Installation .......................................................................................................................................................9
Installation terminals ........................................................................................................................................9
Configuration switches.....................................................................................................................................9
Main menu .....................................................................................................................................................10
Settings menu........................................................................................................................................1 to 11 4
Door panel call screen....................................................................................................................................15
Communication screen ..................................................................................................................................16
Image and communication settings ................................................................................................................17
Timed 'do not disturb' menu....................................................................................................................18 to 19
Intercom menu...............................................................................................................................................20
Wiring diagrams............................................................................................................................................... to21 24
Cross sections and distances.........................................................................................................................21
One apartment with one access panel and one monitor ..................................................................................21
One apartment with two access panels and one monitor.................................................................................21
One apartment with up to two access panels and up to four monitors in cascade .............................................22
One apartment with up to two access panels and up to four monitors in distribution .........................................22
Connection of a lock release...........................................................................................................................23
Connection of an auxiliary device at the relay output .......................................................................................23
Connection of an output button.......................................................................................................................24
Connection of an external camera ..................................................................................................................24
Connection for an apartment door button........................................................................................................24
Special codes ..................................................................................................................................................25 to 26
Cleaning the monitor ................................................................................................................................................27
Cleaning the door panel............................................................................................................................................27
Compliance..............................................................................................................................................................28

3
SYSTEM OPERATION
RECOMMENDATIONS
- Preferably use a Golmar cable (2x1mm²).RAP-GTWIN/HF
- The wiring must run at least 40cm away from any other wiring.
- before making modifications to the device.Always disconnect the power supply
- The installation and handling of these devices must be carried out by authorised personnel.
- Check all connections before starting the device.
-Always follow the instructions contained in this manual.
To make a call, the visitor needs to press the door panel button: an audible tone indicates that the call is being made
and LED on the door panel illuminates.At this moment, the apartment's monitor(s) receive(s) the call.
In systems with two access doors, the other door panel automatically disconnects; if another visitor attempts to call, a
number of tones will indicate that the system is busy and LED on the door panel will illuminate.
Upon receiving the call, the image will appear on the screen of the master monitor (and slave 1, if it exists) without the
visitor knowing and icon displayed on the screen will blink green. To view the image from slave monitors 2 or 3,
press one of the buttons of the monitor to display the image.(located above the raised dots for the visually impaired)
If the call is not answered within 45 seconds, door panel LED will turn off and the system will become free.
To establish communication, press the button below the off-the-hook icon shown on the screen. Door panel
wLED ill illuminate. Communication will last for 90 seconds or until the button below on-the-hook icon shown
on the screen is pressed. When communication has ended, door panel LED will turn off and the system will
become free.
To open door or activate auxiliary output of the door panel, press the button below the icon or press the
hidden push button below the icon displayed on the screen. A single press activates the lock release or auxiliary
output for 3 seconds and LED on the door panel illuminates.
,
Detailed operation of the monitor is described on pp. 8 to 2 .0
12
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
1
2

4
FA-G2+/ POWER SUPPLYLITE
Description
Installation
The fitting and handling of the power supply must be carried out by authorised personnel in the absence of
electrical current.
Install the power supply in a dry, protected and ventilated location. Make sure that the vents are not obstructed.
Use a DIN 46277 rail for fastening ( elements).4
Note that current regulations stipulate that the power supply must be protected by a circuit breaker.
To prevent electric shock, do not remove the protective cover without first disconnecting the power supply. Replace
it once all connections have been made.
Connect the wires to the installation terminals following the instructions in the diagrams.
C
A. Monitor Bus connection terminals.
B. Door panel Bus connection terminals.
C. Protective cover for the current input.
D. Current input connection terminals.
E. Detail of the current input terminals without
protective cover.
NL
12240141 V01
OUTPUT
M
GOLMAR S.A.
C/ Silici, 13
08940 - SPAIN
MADE IN CHINA
BUS 30V 2V 0.5A±
INPUT ~100-240V
0.8A 50-60Hz
FA-G2+/LITE
PL
BUS BUS
N L
BUS(M) BUS(PL)
DIN rail.
Fastening tab on the DIN rail.
DIN rail.
B
D
E
A
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE

5
SOUL PANEL-7/LITE
Description
A
B
C
F
E
D
J
I
G
J
G
H H
B
C
D
L
M M
K M
Q
O
O
P
I
N
T
K
R
S
A. System status icons:
Call in progress.
Communication established.
Lock release activated.
System busy.
B. System status indicator lights.
C. Ambient lighting sensor.
D. Night viewing lighting.
E. Protective polycarbonate.
F. Nameplate label.
G. Speaker grill.
H. Colour camera.
I. Call button(s).
J. Microphone hole.
K. Front fixing screw.
L. Illumination module.
M. Wall fixing hole (x3). Do not overtighten the
fixing screws.
N. Illumination module gasket.
O. Installation terminals.
P. Cable grommet.
Q. Illumination module connector.
R. Configuration switches.
S. Volume control potentiometer.
T. No function.
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE

6
Installation
The door panel has been designed to withstand diverse environmental conditions. It is however advisable to take
extra precautions to prolong its service life, such as locating it in a covered area.
For optimum image quality, avoid direct contact from light sources (sunshine, street lights, etc.).
For correct installation: (locate the top of the door panel at a height of 1.65m).
1. Remove the metal front piece of the door panel by loosening the bottom screw with the Allen key supplied. On
the back of the front piece, you will find the button personalisation label.
2. Remove the screws that secure the .
Illumination module
3. Present the door panel to the wall, positioning the top at 1.65m. Pass the installation cables through the cable
grommet.
4. Drill three 6mm holes at the indicated points (M), see p. 5. Insert the plugs supplied and fix the door panel to the
wall using the screws supplied.
5. Connect the cables to the removable terminals following the instructions in the installation diagrams.
Before replacing the and closing the door panel, perform the necessary settings (illumination module address door
panel illumination module, audio level setting, etc.), as indicated throughout this manual. Make sure that the
gasket is properly fitted.
Installation terminals (O)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
BUS BUS CV- CV+ AP+
C NA GND CCTV AP-
ON
1 2 3 4
BUS BUS, : communications bus (non-polarised).
CV CV-, +: lock release output 12Vdc (maximum 270mA).
AP AP+, -: remote activation button connection. Note: For correct
operation, the monitor's address 1 must be connected to
the Bus.
IMPORTANT: Installation with 2 access door panels and
AP button on both door panels, one of the door panels
must connect the AC lock release (instead of DC lock
release). SAR-12/24 required,
relay a TF-104 transformer&
see pages 23 to 24.
C, : potential-free relay output (maximum 6A/24V).NA
GND CCTV, : input for external analogue camera.
SOUL PANEL-7/LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE

7
Configuration switches (R)
Configuration changes should be made with the equipment turned off. If they are performed with the equipment
turned on, disconnect it for 10 seconds after any modification.
All switches are factory set to OFF.
Switch 1.
Defines the door panel address.
Switch 2, must be OFF.
OFF-OFF
OFF OFF-
O -OFFN
Door panel 1 Door panel 2
Apartment 1
Switches and must be OFF.3 4
Setting the audio level
If the audio volume on the door panel after starting up the device is not adequate, use the volume control
potentiometer (S). This setting affects the communication and confirmation tone audio level.
BUS BUS CV- CV+ AP+
C NA GND CCTV AP-
ON
1 2 3 4
ON
12 3 4
ON
12 3 4
ON
1 2 3 4
S
SOUL PANEL-7/LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE

8
ART /G2+ MONITOR7 LITE
Description
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
A. Speaker.
B. Notification icons:
Power on indicator.
Do not disturb.
Auxiliary relay activated.
Door opening.
C. Hidden button indicator LEDs :
To access the main menu (monitor in standby), press
either of the 2 buttons located above the/
raised dots for the visually impaired (see ).page 10
In call/ communication: press button to start or end
the communication.
In call/ communication: one press will activate the
lock release 1 for 3 seconds.
In call/ communication: an LED shows the location
of each of the hidden buttons.
T button/he function of each hidden button is shown
on the monitor screen with an icon located just
above each button (see ).pp. 10 to 20
D. Raised dots for the visually impaired.
In standby:
Above the raised dots for the visually impaired / are
the buttons that access the main menu.push
In call
Above this raised dot is the 'Start/end communication'
button .
Above this raised dot is the 'Door opening' button .
E. 7” TFT colour screen.
F. Golmar use.
G. Microphone.
H. Wall mounting connector fixing (x4).
I. Configuration switches.
J. Installation terminals.
*
Hidden button
pressing area
F
A
E
B
DG
*
C
H
I
J
H
H
H
J
SA
GND
HZ
HZ
BUS
IN
ON
1 2 3 4 5 6 7 8
BUS
OUT
DIP 1 to 7
Monitor address
SA
GND
HZ
HZ
BUS
IN
BUS
OUT
DIP 8
EOL resistor
OFF = 0
ON = 1
128
codes
12210705 V02
MONITOR 7” ART 7 LITE/G2+
GOLMAR S.A.
C/ Silici, 13
08940 - SPAIN
WARNING
TO PREVENT FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS
DEVICE TO RAIN OR MOISTURE
CAUTION
TO PREVENT ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
MADE IN CHINA
128 codes
General Panel

9
Installation
Avoid dusty or smoky environments or locations near sources of heat.
For proper installation, use the template supplied with the product.
1. Position the top of the template at a height of 1.65m.
2. If you are going to use an embedding box to pass the wiring through, make sure that it is in line with the holes
corresponding to the box model chosen and fix the connector. If you prefer to fix the connector directly to the
wall, make four 6mm holes at the points indicated (A), insert the wall plugs supplied and screw in the connector.
3. Pass the installation wires through the middle hole and connect them to the removable terminals as shown in the
wiring diagrams. Before connecting the removable terminals to the monitor, configure the switch as indicated
below.
4. Connect the removable terminals to the monitor and place the monitor in front of the connector, making sure the
fixings line up. Move the monitor downwards to secure it.
Installation terminals (J)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
Configuration switches (I)
Switches 1 to 7.
These assign the address of the corresponding monitor to its call button on the door panel. Switches to must2 7
remain in the OFF position.
Apartment 1
Switch 8.
This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
ON
1 2 3 4 5 6 7 8
ART /G2+ MONITOR7 LITE
Note: HZ push button function mode: When HZ push button is pressed will be call tone and activate the output of
auxiliary call repeater with standby monitor call process m ation process HZ tone with lower audio level, , com unic ( ),
intercom .process and "Do not disturb" mode
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Switch 8 to ON
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
Switch 8 to OFF
To define whether the monitor is master or slave:
To define whether the monitor is master or slave (see special codes page 25 to 26). Each apartment must have one
master monitor, and only one.
SA
GND
HZ
HZ
ON
1 2 3 4 5 6 7 8
BUS
OUT
BUS
IN
BUS IN: Communication bus input to monitor (non-polarised).
BUS OUT: Communication bus output to additional monitor (non-polarised).
SA GND, :Auxiliary call repeater output (max 50mA/12V), relay SAR-12/24.
HZ HZ, : Apartment front door button input:
Connect only on the master monitor. The signal received is then
transmitted to the slave monitors in the same apartment through the
BUS.

10
Main menu
ART /G2+ MONITOR7 LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Press the button below icon to display the image from the door panel. Note: This enablesmaster
the door panel camera to be changed, the audio on the corresponding door panel to be activated
and the door to be opened (see p. 1 ).5
Press the hidden button below icon to access the menu of the intercom between other monitors in
the same apartment or other apartments (see pp. ).20
Press the hidden button below icon to make changes to the system settings (see pp. -1 ).11 4
Press the hidden button below icon menu and enable theto access the 'Do not disturb'
function. , press the hidden button below iconIf the monitor is in 'Do not disturb' mode
t ringtone on theo disable the function: If the monitor is in ’Do not disturb’mode, the
monitor does not sound when a call is received and the notification( “HZ”p g )see note a e 9
icon will illuminate.
Hidden button
pressing area
LED indicators
Raised dots for the
visually impaired
Main menu
If the device is in standby (screen switched off), to access the main menu, press either of the 2 buttons /
(located above raised dots / for the visually impaired) on the monitor. Then press the hidden buttonbutton/
located just below the corresponding icon. The device will return to standby mode after 0 seconds without2
activity.
No function.

11
Settings menu
ART /G2+ MONITOR7 LITE
Continued overleaf
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Returning to the main menu: Press the hidden button below icon to return to the main menu.
Settings menu
The 'About' screen provides information about the monitor, such as the software version, address
and whether it is master or slave (M, S1, S2 or S3).
It enables updated versions of the manual to be downloaded to a mobile or tablet, for which it is
necessary to have a QR code scanner app installed.
It enables the monitor to be restored to factory settings, such as melodies, call volume, etc.
Press the button below icon to return to the settings menu.
To restore the monitor to factory settings, press the hidden button below icon to access the
factory reset menu, then press the hidden button below icon to perform this function. Press
the button below icon to return to the 'About' screen.
Press the button below icon to return to the settings menu.
FW
0 /0 M1
1.03

12
Settings menu
ART /G2+ MONITOR7 LITE
Continued overleaf
Continued from previous page.
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Selecting the melody and call volume: Press the hidden button below icon to access the settings
screen. In order to identify the origin of the calls when you are not in front of the monitor, select
different melodies and the desired call volume. Go to the option to be modified by pressing the
button/ hidden button below corresponding icons / , then press the hidden buttons below
corresponding icons / to select the melodies and desired call volume. Press the button below
icon to validate the changes made and return to the settings menu.
Option selection screen
105
205 03
01
02
305
405
03
Settings " " mode:automatic door opening with the specialThis selection is visible in the settings menu,
code '0441' (Doctor mode) already entered for automatic door openingin the monitor (see special
codes pp. 2 6). Then press the button below icon to access the settings menu.5 to 2
1
Option selection screen
07h
24h

13
Settings menu
Continued overleaf
ART /G2+ MONITOR7 LITE
Continued from previous page.
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
To enable the automatic door opening (after 3 seconds of receiving a call from the door panel),
go to the option with icon by pressing the button below icon/ hidden button corresponding
/ hiddenand select the option by pressing the button below icon Press the button.
below icon to return to the settings menu.
If you wish disable the automatic door opening , go to the option with icon by pressing the
button below icon , deselect the option by pressing the/ hidden button corresponding / and
hidden button below icon . .Press the button below icon to return to the settings menu
(This function is disabled by default. To enable it, see pp. .2 to 25 6)
To set a period of time for automatic door opening (after 3 seconds of receiving a call from the
door panel), go to the option with icon by pressing the button below/ hidden button
corresponding icon and select the option by pressing the button below icon ./ hidden
Then you can set a period of time for opening the door , by(from 1h to 24h) ' ' function mode
pressing corresponding buttons / , and validate the changes made by pressing thehidden
hidden button below icon . Press the button below icon to return to the settings menu.
(This function is disabled by default. To enable it, see pp. ).2 to 25 6
1
1
1
24h
24h
24h
Time period setting screen
07h
24h

14
Settings menu
ART /G2+ MONITOR7 LITE
Continued from previous page.
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Settings menu
Main menu
Press the button below icon to return to the .main menu If the ' ' mode isautomatic door opening
enable (see pages to 13) the icon will be displayed12 in the top left of the screen in the main
menu and the blink.
notification icon will

15
Door panel call screen
ART /G2+ MONITOR7 LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
This screen is displayed when you receive a call or when you press the button below icon of the main menu.
During a call, icon displayed on the screen will blink green (during the call process). In the top of theright
screen, the source of the image is displayed. The call has a duration of 45 seconds.
Press the hidden button below icon to cancel the current call or display and return to the main
menu.
Press the button below icon / to start or end audio communication with the door
panel displayed respectively. Communication has a maximum duration o 90 seconds.f
Once communication has ended, the screen will turn off.
Press the hidden button below icon to change the source of the image as long as the system has
more than one door panel or has an external camera connected and display has been activated
(see pp. ). It is possible to make the change during display, call and communication2 to 25 6
processes.
Press the button below icon to activate the lock release (or device connected to the CV output of
the door panel) for 3 seconds (factory setting, ). During activation, indicator illsee pp. 25 to 26 w
illuminate.
P or device connected to the relayress the hidden button below icon to activate the lock release (
output of the door panel) for 3 seconds (factory setting, ). During activation,see pp. 25 to 26
indicator will illuminate.
1
2
1
2
1
12
No function

16
Communication screen
ART /G2+ MONITOR7 LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
This screen is displayed during a communication process. In the top of the screen, the source of the image isright
displayed.
Press the hidden button below icon to access the image and monitor in communication volume
settings menu. Go to the option to be modified by pressing the hidden button belowbutton/
corresponding icons / , change to the desired level by pressing the hidden buttons below
corresponding icons / and validate the changes made by pressing the button below icon ,
(see p. 1 )7
1
12
Press the button below icon / to start or end audio communication with the door
panel displayed respectively. Communication has a maximum duration o 90 seconds.f
Once communication has ended, the screen will turn off.
Press the hidden button below icon to change the source of the image as long as the system has
more than one door panel or has an external camera connected and display has been activated
(see pp. ). It is possible to make the change during display, call and communication2 to 25 6
processes.
1
2
No function.
Press the button below icon to activate the lock release (or device connected to the CV output of
the door panel) for 3 seconds (factory setting, ). During activation, indicator illsee pp. 25 to 26 w
illuminate.
P or device connected to the relayress the hidden button below icon to activate the lock release (
output of the door panel) for 3 seconds (factory setting, ). During activation,see pp. 25 to 26
indicator will illuminate.
1
2

17
Image and communication settings
ART /G2+ MONITOR7 LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
During a communication process, press the hidden button below icon to access the image and monitor in
communication volume settings menu.
The following settings menu will then appear (brightness, contrast, colour and monitor in communication volume).
Go to the option to be modified by pressing the hidden button below icons andbutton/ corresponding /
change to the desired level by pressing the hidden buttons below corresponding icons . To exit the screen/
settings and monitor volume menu and validate the changes made, press the button below icon .
1
12
1

18
Period of time for 'do not disturb' mode menú
ART /G2+ MONITOR7 LITE
Continued overleaf
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Do not disturb' mode settings: If the device is in standby (screen switched off), to access the main menu,
press either of the 2 buttons (located above raised dots / for the visually impaired) on the/
monitor You can set abelow icon to access the settings screen.
. Then press the buttonhidden
period of time during which the monitor will not sound when receiving calls .see note a e( “HZ”p g )9
To do so, enable the timer function and choose the time period. From the main menu, you can
disable the 'Do not disturb' function regardless of the timer status.
07h
To enable the ’Do not disturb’mode in which the monitor will not sound when receiving calls (see note "HZ"
page ) go to the option with icon by pressing the button below icon9 , / hidden button corresponding
/ and select the option by pressing the button below icon notification icon will
and the
illuminate. Press the button below icon to return to the main menu.
If you wish disable the 'Do not disturb' mode, go to the option with icon by pressing the button/
hidden button below corresponding icon / , deselect the option by pressing the button
below icon and the notification icon will be switched off. Press the button below icon
to return to the menumain . From the main menu, you can also disable the ’Do notNote:
disturb’function by pressing the hidden button below icon .
24h
24h
24h
07h
Option selection screen
24h
24h

19
Period of time for 'do not disturb' mode menú
ART /G2+ MONITOR7 LITE
Continued from previous page.
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
Main menu
From the main menu, you can also disable the ’Do not disturb’function regardless of the timer
status by pressing the hidden button below icon .
01h
24h
To set a period of time for in which the monitor will not sound when receiving calls"Do not disturb" mode
(see note "HZ" page ), go to the option with icon pressing the button/ hidden button below9
corresponding icon ./ and select the option by pressing the button below icon Then you can
set a period of time for , by pressing corresponding(from 1h to 24h) 'Do not disturb' mode hidden
buttons / , and validate the changes made by pressing the button below icon notification
, the
icon will and return to the main menu screen.illuminate
Time period setting screen

20
Access the intercom menu as described on p. . From this menu, you can contact another monitor(s) in your10
apartment (internal intercom)
Select option to perform an internal intercom call.
If during an intercom process with another monitor a call is received from the door panel, the intercom process will be
terminated, and the door panel call will be received on the corresponding monitor.
The selection and : Not use.
Press the button below icon to return to the main menu.
Intercom menu
ART /G2+ MONITOR7 LITE
SOUL S5110/ART VIDEO DOOR ENTRY SYSTEM KIT7 LITE
To make an internal intercom call (to another monitor(s) in the same apartment), go to the option with
icon by pressing the hidden button below corresponding icons / and press the hiddenbutton/
button below icon to access the monitor selection menu (in the same apartment). Note: You will find
information about the monitor itself with the address, Master, Slave 1 to Slave 3 of the monitor in the
'About' menu, (see p. ).11
Then press the hidden button below icons / to select the monitor to be called and press thebutton/
hidden button below icon to make the call. The monitor making the call will play a confirmation
melody and indicate with a blink the monitor called. To cancel the call, press the hidden button below
icon . Press the button below icon to return to the intercom menu. The monitor receiving the call
will play a confirmation melody showing on screen with a blink the monitor making the call. Press the
hidden button below icon to establish communication and press the hidden button below icon
to end communication.
S1
M S2
S3
0 0 1
S1
M S2
S3
001