golmar IPG+ ART 1/G+ User guide

ART 1/G+
ART 1/G+ V01 REV.0121|ENGLISH
INSTALLER MANUAL

CATEGORY 1_HEADERCATEGORY 2_HEADER
2Footer Infos
ART 1/G+IP G+
2
www.golmar.es
INDEX
1. Safety cautions and warnings............................................................................................................................3
2. Specications ......................................................................................................................................................3
3. Device description..............................................................................................................................................3
3.1. Jumper description ....................................................................................................................................4
4. Device installation..............................................................................................................................................4
5. Module conguration through the Web Client..............................................................................................5
5.1. Settings ........................................................................................................................................................5
5.2. SIP Server....................................................................................................................................................5
5.3. About ...........................................................................................................................................................6

3
ART 1/G+ IP G+
www.golmar.es
- TCP/IP video intercom system with technology IP-G+.
- Installation over existing ethernet network (D4L-G+/POE are required).
- Up to 98 blocks in one system.
- Up to 19 entry panels at each block.
- Up to 19 general panels at each installation.
- Up to 799 ats per each block.
- Up to 19 guard units for the general compound and 9 guard units at each block.
- Up to 32 ONVIF cameras.
2. SPECIFICATIONS
- e installation and setup of this equipment must be done by an authorized installer.
- e current regulations oblige to protect the power supply by means of a thermal magnetic circuit breaker.
- All the installation conduits must distance at least 40 cm from any other installation.
- In regards of the power supply FA-G+:
- Do not tight with excessive strength the screws of the terminal block at FA-G+ power supply.
- Install the power supply in a dry and secure area, protected against water drops.
- Avoid placing the power supply close to heating sources, humid or dusty areas.
- Do not cover the power supply ventilation openings area to assure air ow circulation.
- To prevent damages, the power supply has to be strongly mounted. Use a DIN rail 46277 (8 DIN) to x it.
-To avoid an Electrical shock, do not remove the protection cover and do not manipulate the cables connected to the power terminals.
1. SAFETY CAUTIONS AND WARNINGS
3. DEEVICE DESCRIPTION
Speaker.
Microphone..
Capacitive touch-buttons.
Auxiliary sounder connector.
12V local power connector.
Apartment doorbell connector.
Supply voltage selector jumper.
RJ45 connector.

4
ART 1/G+IP G+
www.golmar.es
3.1. Jumper descripon
e jumper allows to select which voltage amplitude supplies the device as is not the same voltage when the apartment unit is connected to
an output of a D4L-PoE/G+ switch as it is when connecting it to a switch providing 48V standard PoE.
- Position 48V (default).
e device is ready to receive 48V standard PoE.
- Position 18V.
e device is ready to receive 18V from a D4L-PoE/G+ or from a
DCS-G+.
4. DEVICE INSTALLATION
For the device installation, rst we must place the mount in a at surface and at the most convenient height for correct handling.
At a height of 1,65m would be the optimal choice for anyone to maintain an adequate distance between the microphone and their face when
speaking.
1,65m
1,45m máx
1,85m máx
Mount of the hands-free audio unit.
Necessary elements to complete an installation:
• FA-G+ power supply for each 8 devices (door panels, monitors…).
• Distribute the dierent devices through D4L-G+/PoE distributors of 4 distributed outputs.
• Choose the 6502/G+ coded panel, or a modular composition of the Nexa panel with the El632/G+ audio and video module to
be able to register the devices..
• Choose ART 7/G+ video units, or ART 7W/G+ units with integrated WiFi to receive calls via the G2CALL+ app (available for
Android and IOS).
• Add ART 7/G+/PCM and ART 7W/G+/PCM video units if you want that the internal unit has a PCM/G+ private call module
In case of daisy-chain distribution of devices (IN/OUT), use DCP/G+ injector with the FA-DC48/G+ power supply and DCS/G+
Ethernet switches in monitors.

5
ART 1/G+ IP G+
www.golmar.es
5. MODULE CONFIGURATION THROUGH THE WEB CLIENT
To do the device conguration, it will be necessary to connect to its web client as it is not possible to do it in the own device.
We will connect with the browser to the device IP that will be the 10.0.0.254 as it has all the default factory settings.
It is essential that there is no other device connected to the network with factory default settings, as when sharing the same IP address would
cause a conict and we would not be able to acces the device web client with our computer.
5.1. Sengs
Sip Server
About

APARTMENT UNIT

Network
 10.0.7.105
 255.0.0.0
Gateway 10.0.0.1
Server IP 10.0.14.9

 5
 1
 1
 1
 99901

Manual entering of network
parameters.
Dialing code length (5).
Block number (1-98).
Apartment address (1-799).
Unit number (1-6).
(**) Direct guard call
address.
(***) Automatic answer.
(****)Press HZ to call
the guard unit.
(*) Address to which the device will call when the icon is pressed.
(**) With this mode enabled, when the hands-free audio unit receive a call it won’t be necessary to press icon to answer the call, this
automatically enables the communication.
(***) When this mode is activated, we will make a call to the address assigned in the “Guard” eld when pressing the push-button connected
to HZ.
5.2. SIP Server
L
Name
SERVER LIST
Apply
Enabled

SERVER INFORMATION
Delete
1
2
3
4
5
6
7
8
9
10
11
10.0.128.8
5060
grandstream
IP Address
Port
User
Password
Transmission mode*
*Transmission mode
0 IP - 1 to 30 SIP Servers
1000
*****
1
grandstream
In the “SIP Server” section we will be able to include the device in a PABX telephone switchboard to receive calls through an extension which
we previously assigned to the device in the switchboard.
We must select the server of the list on the le-hand of the screen and ll the requested parameters as follows:
Enable/Disable the SIP
server.
SIP server name.
Switchboard IP address.
Transmission port. e
most frequent is the 5060.
Extension and password
created for the device.

CATEGORY 1_HEADERCATEGORY 2_HEADER
6Footer Infos
5.3. About
Sip Server
About

MCU 1.00
Firmware 1.01
Hardware VER.B
Server IP 10.0.14.9


10.0.7.105

In the “About” section we will nd the information of the device conguration as well as rmware and hardware versions. We also nd a QR
link wich forward us to the product websit where we will nd in the “Downloads” section all the product manuals.
We will be able to reboot the device, update its FW version and restore the device to factory default settings.
Restart the device. Return the device to factory settings. Update Firmware.
6
www.golmar.es
IP G+ ART 1/G+

Sist
emas de comunicación S.A.
C/ Silici 13. Poligon Industrial Famadas
08940 – Cornellà del llobregat – Spain
[e-mail]
Telf: [phone]
www.golmar.es