Roger PR411DR-SET User manual

PR411DR-SET Installation Manual 2020-10-07
1/2
Roger Access Control System
PR411DR-SET Installation Manual
Controller firmware version: 1.18.10 or newer
Product version: 2.0
Document version: Rev. B
This document contains minimum information that is necessary for initial setup
and installation of the kit. The detailed description of configuration parameters
and functionalities of all components is specified in respective Operating
manuals available at www.roger.pl.
INTRODUCTION
PR411DR-SET is designed to control single door in RACS 4 system. The door
can be read-in or read-in/out type when equipped with PRT series readers
(RACS CLK/DTA), Wiegand interface readers or Magstripe interface readers.
The kit includes PR411DR-BRD access controller and ME-1 metal box with
18VAC/40VA transformer. The box is adapted to installation of 7Ah battery for
emergency supply. All elements of controlled door including readers and door
lock can be supplied from the kit.
PRELIMINARY CONFIGURATION
Preliminary configuration requires addressing of the controller on RS485 bus in
range of 00-99. All controllers on this bus must have unique addresses. It is
recommended to configure the address of controller by means of jumpers. Other
methods are explained in controller’s manual.
Fig. 1 Addressing with jumpers
CONFIGURATION WITH PR MASTER PROGRAM
Configuration with PR Master enables to define the logic of controller including
users and access rights. More information is given in PR Master manual. The
communication with controller requires connection to computer via
communication interface (e.g. UT-4DR, UT-2USB, RUD-1) or via CPR32-NET-
BRD network controller.
MEMORY RESET
Memory reset procedure resets all settings to default ones. RS485 address
which is configured with jumpers remains unchanged.
Memory reset procedure:
1. Disconnect power supply from controller.
2. Short CLK and DTA lines.
3. Restore power supply - LED OPN (green) will start to pulsate.
4. Disconnect CLK and DTA.
5. Connect PRT series reader to CLK and DTA lines (without switching power
supply off) and execute further steps by means of that reader.
6. Read any card at the reader, this will be a new MASTER card
7. After a few seconds the controller will restart automatically and switch to
normal mode.
FIRMWARE UPDATE
New firmware can be uploaded to the controller with RogerISP software. The
latest firmware file is available at www.roger.pl.
Firmware update procedure:
1. Connect the device to RUD-1 interface (fig. 2) and connect the RUD-1 to
computer’s USB port.
2. Place jumper on FD contacts (fig. 1).
3. Restart the device (switch power supply off and on or press RST button) –
LED SYS (orange) indicator will be switched on.
4. Start RogerISP software, select serial port with RUD-1 interface port, select
the option USB-RS485 Converter and indicate path to firmware file (*.hex).
5. Click Update to start firmware upload with progress bar displayed.
6. When the update is finished, remove jumper from FDM contacts and restart
the device.
Fig. 2 Connection of the controller to RUD-1 interface for firmware update
Note:
1. If the controller is not responding after firmware update and LED SYS (orange)
indicator is switched on then it is necessary to start memory reset procedure.
2. If firmware update is not successful for any reason then repeat the procedure.
3. UT-2USB interface can be used instead of RUD-1 interface for firmware
update.
POWER SUPPLY
The kit is supplied from 18VAC/40VA transformer. The metal box offers space for
installation of typical 7Ah backup battery which is connected to BAT+ and BAT-
terminals of PR411DR-BRD controller.
Fig. 3 PR411DR-SET
The installation can be done only by qualified person with all
necessary certificates concerning connection and maintenance
of 230VAC and low voltage networks.
Prior to starting the installation it is necessary to ensure that
230 VAC circuit is disconnected. All works inside the box must
be carried out with 230VAC supply voltage disconnected.
It is forbidden to use the kit without properly executed and
operational earthing system.

PR411DR-SET Installation Manual 2020-10-07
2/2
TAMPER DETECTOR
The metal box is equipped with door contact which can be connected to one of
the inputs (e.g. IN8) and GND terminal of the controller. The anti-sabotage
function can be assigned to the input with PR Master software.
APPENDIX
Table 1. PR411DR-BRD screw terminals
Name
Description
BAT+, BAT-
Backup battery
P1, P2
18VAC input power supply
NO, COM, NC
30V/1.5A DC/AC (REL1) relay
CLK, DTA
RACS CLK/DTA bus
GND
Ground
A, B
RS485 bus
IN1-IN8
Input lines
IO1, IO2
15VDC/1A transistor output lines
TML
12VDC/0.2A output power supply (for readers)
AUX
12VDC/1.0 output power supply (for door lock)
NO, COM, NC
230V/5A DC/AC (REL2) relay
Table 2. PR411DR-BRD LED indicators
Name
Description
AC
AC supply
SYS
Various signalling functions
OPN
Door unlocked
STAT
Current arming mode
LINK
Data transmission on RS485 bus
Table 3. Specification
Supply voltage
230VAC, 50/60Hz (-15%÷+10%)
Power supply
AWT150 TRP/40/16/18 transformer
Short circuit and overload
protection
Yes
Metal box
DC01 0.7mm metal sheet, white colour RAL9016
Tamper protection
NO/NC detector, 50VDC/50mA
Distances
Between controller and communication interface
(RS485): max. 1200m
Between controller and PRT reader (RACS
CLK/DTA): max. 150 m
IP Code
IP20
Environmental class
(acc. to EN 50133-1)
Class I, indoor general conditions, temperature:
+5°C to +40°C, relative humidity: 10 to 95% (no
condensation)
Dimensions H x W x D
295 x 285 x 90 mm
Weight
3.5 kg
Certificates
CE
Fig. 4 Typical connection of controllers (CPR32-NET-BRD)
Fig. 5 Typical connection of controllers (CPR32-SE-BRD)
Fig. 6 Typical door control
Notes:
In case of read-in door, single reader is connected to the controller and then
such PRT reader can have default ID=0 address. If two PRT readers are
connected to the controller for the purpose of read-in/out door then one of the
readers must be addressed as ID=1 according to its manual.
Pre-programmed EM125kHz MASTER proximity card is included with
PR411DR-SET. It can be used at PRT reader to open door.
PR controller configuration from computer with PR Master software requires
UT series interface or CPR32-NET-BRD network controller.
Diagram includes door with electric strike. In case of electromagnetic lock, the
NC terminal of relay is used instead of NO terminal.
Diagram includes exit button. In case of read-in/out doors it can be used for
emergency door opening.
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [email protected]l
Web: www.roger.pl