Gossen MetraWatt DIGISKY User manual

Revision level:
04-03.2014
Please checkthat the exposuremeter and accessories as
detailed below are included inthe box. If thecontents are
incomplete, pleasecontact your local dealer.
DIGISKY
V070A rechargeable battery
Power supply and USB connector cable
Carrying strap
CD ROM (includes operating instructions)
Quick-start guide
DIGISKY
Quick-start Guide –15448 –V1.18
Contents
Page
Preparation
2
Meter Overview
3
Measuring Modes
4
Function Selection
4
AmbientLight
5
Flash Light
6
MOVIE
7
Main Menu
8
FCC & IC (USA)
9
Safety Precautions
10
Preparations required for use of the exposure
meter and its basic functions are described in
these instructions.
Please read the
operating instructions
(on the CD) first.
Essentials

2 GOSSEN Foto- und Lichtmesstechnik GmbH
How to insert and charge the battery
The DIGISKY works with a device-specific, rechargeable lithium-
ion battery. Use the V070A rechargeable battery and the USB
battery charger included with the exposure meter.
In order to insert the rechargeable battery, it is necessary to
have a (Philips) recessed head screwdriver.
Switch your DIGISKY off or wait until the exposure meter is
switched off automatically.
Unscrew the battery cover at the back of the meter with a
(Philips) recessed head screwdriver, and then pull it down and
out of the housing.
Insert the battery into the compartment as shown in the figure.
Make sure that the battery is inserted with correct polarity
(+ and –)! Then place the battery cover over the battery
compartment and secure it with the screw.
Connect the cable to the USB port at the exposure meter first,
and then insert the mains plug into an electrical outlet.
The battery can also be charged using a USB port at a PC.
Remove the mains plug to this end, and connect the USB plug to
your PC.
The charging indicator lights up red while the battery is charging.
After the battery has been fully charged, the indicator will light up
green.
To protect the battery pack and prolong its life, do not
charge it for longer than 24 hours without break.
1 Unscrew
2 Remove cover
3 Insert battery

GOSSEN Foto- und Lichtmesstechnik GmbH 3
Switch DIGISKY off
Incident light,
flat diffuser
Meter Overview
Diffuser ring for incident
light/ reflected light
measurement, off
LEDs for status
of the meter
Display panel
Data key
Ring controller
Socket for connecting
flash synchronizing cable
Carrying strap
holder
USB port for charging battery
or data transmission
Meter cell f. reflected
light measurement
Menu key
Measurement key
User
Cam 1
Cam 2
Cam 3
Movie
Retractable
diffuser head
f.spherical/
flat /reflected
measurement
ISO
speed
Measuring
function
Measured
values
Analog scale
EV
Cor.
Batt.
Incident light
Spherical diffuser
Reflected light

4 GOSSEN Foto- und Lichtmesstechnik GmbH
Function Selection: Ambient Light / Flash Light
Use the menu key ...
to select a function.
Measuring Modes
Spherical incident light
measurement
. Reflected light meas.
Flat incident light meas
Off
DIGISKY off
RF Function Selection: All / Group
Use the data key ...
to select “All” or a group.
Switching the DIGISKY on after:
Standby (display off)
Activate by pressing any key or turning the instrument head
Automatic switching OFF
Activate with menu key only
Manual switching OFF
Turn instrument head to measurement modes

GOSSEN Foto- und Lichtmesstechnik GmbH 5
Ambient Light
Use the ring
controller ...
to set time /
f-stop
Use the ring
controller ...
to select the desired
value.
Press the measurement key to make a measurement.
Contrast measurement: press and hold the measurement key.
Contrast measurement: use the data key to display the average, minimum and maximum value.

6 GOSSEN Foto- und Lichtmesstechnik GmbH
Flash light
Use the ring
controller ...
to select the desired
synchronization
speed.
RF
Use the data key ...
to select the desired
group.
Press the measurement key ...
to perform a measurement.
NonCord
Approx. 45 seconds measurement standby duty
Cord
Synchronizing cable –flash is triggered
RF
RF module –flash is triggered

GOSSEN Foto- und Lichtmesstechnik GmbH 7
Movie
Settings (f-stop, sector angle, sensitivity etc.) are set in the main menu.
EV analog display
Illuminance,
luminance
Measured value with
correction
Press the measurement key to perform a measurement.
For continuous measurement: press and hold the measurement key;
use data key to display the average, minimum and maximum value.
Use the menu key ...
to switch the display
from f-stop value to
photometric value.
Shutter
angle
CINE Speed

8 GOSSEN Foto- und Lichtmesstechnik GmbH
Main Menu
Press and hold menu key ...
to select a menu.
Use the ring controller ...
to select a user.
to select a setting.
Use the ring controller ...
Press the measurement key ...
to confirm.
to select a submenu.
Use the measurement key ...
to exit the menu.
to select a value.

GOSSEN Foto- und Lichtmesstechnik GmbH 9
FCC & IC - USA
Modifications
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to
operate the equipment.
Conditions of
Operations
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
15.105
Class B digital device
or peripheral
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
15.105
Class A digital device
or peripheral
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.

10 GOSSEN Foto- und Lichtmesstechnik GmbH
Safety Precautions
In the event of malfunctioning, switch the light meter off immediately.
If the event that smoke develops or unusual odors become apparent, which are caused by either the measuring instrument or the power
supply, disconnect from mains power immediately and remove the rechargeable battery from the instrument in order to prevent possible
fire. Continuing to operate the measuring instrument or the power supply after such malfunctions have occurred may result in severe
injury. Please contact your local dealer or Gossen-Service in order to eliminate malfunctioning. If you bring or send the instrument in for
repairs, make sure that the rechargeable battery has been removed first.
Never use the measuring instrument in proximity to flammable gases.
Electronic devices must not be used near flammable gases. Otherwise there would be danger of explosion and fire.
Never hang the meter and/or the carrying strap around the head or neck of a child.
Danger of strangulation exists if the carrying strap is hung around the head or neck of a child.
!!
Displaying Documentation in PDF Format
Adobe Reader or Adobe Acrobat Reader must be installed to your PC if you want to display product documentation in PDF
format. If this software has not already been installed to your PC, it can be downloaded from the following website:
http://www.adobe.com.
This icon indicates that this product must be disposed of separately.
The following must be observed by users in European countries:
This product may only be disposed of separately at a designated collection point. It may not be disposed
of with household trash.
For further information contact your local dealer or waste disposal authorities.