BEFORE USING FOR THE FIRST TIME
1. Remove all of the various packaging, stickers or accessories from both the
inside and outside of the kettle.
2. Taking care to keep the electrical components on the exterior of the kettle
dry, wipe the interior of the kettle with a damp cloth. If your hand will not
fit inside the kettle, swish warm, soapy water around the interior of the
kettle with the lid closed.
3. Rinse out the inside of the kettle thoroughly with water.
4. With a damp cloth, gently wipe off the exterior of the kettle. Do not wipe
electrical components as this may cause damage to the unit.
5. Dry all parts completely.
6. It is recommended to run one boiling cycle through your kettle before
using it. Following the instructions in “To Boil Water” (below), boil a full
kettle of water. When water has boiled, pour it out and rinse the inside of
the kettle once more. The kettle is now ready for use.
TO BOIL WATER
1. Place the base on a at, stable, heat-resistant surface away from water
splashes and any sources of heat.
2. Make sure that the Removable Filter is properly inserted. See“Removing and
Inserting the Filter” on page 3for instructions on inserting the filter.
3. Open the lid and fill with water through the lid opening. Water must be
filled between the “MIN” and “MAX” levels inside the kettle.
4. Close the lid, ensuring it locks into place.
• Never fill the kettle with any liquids other than water.
• Use distilled water when possible for best taste and to minimize
mineral build-up in the kettle.
10
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS
5. Plug the Power Cord into a wall outlet and place the kettle onto the Power Base.
The kettle will “beep” once to indicate it is on.
6. Press the POWER ( ) button to turn the kettle on. The Blue Illumination Light
will turn on and the kettle will begin heating the water. As the water begins to
heat, the LED Display will show the temperature in real time.
7. Once the water reaches a boil, the kettle will “beep” three times and
automatically stop heating.
8. Using the Easy-Grip Handle, lift the kettle o the Power Base to serve. Do not
touch the glass body, it will be hot.
9. When nished serving, pour out any remaining water and unplug the Power Cord.
• Never open the lid while water is boiling.
• If the kettle is heated with no water, the internal safety mechanism will
automatically turn the kettle o.
• If the lid is not completely closed or if the lter isn’t inserted correctly
the kettle will not automatically turn o.
USING THE KEEP WARM TEMPERATURES
1. Place the Power Base on a sturdy, level and dry surface.
2.Make sure that the Removable Filter is properly inserted. See page 13for
instructions on inserting the lter.
4. Open the lid and ll with water through the lid opening. Water must be lled
between the “MIN” and “MAX” levels inside the kettle.
5. Close the lid, ensuring it locks into place.
5. Plug the Power Cord into a wall outlet and place the kettle onto the Power
Base. The kettle will “beep” once to indicate it is on.
6. Press the POWER ( ) button to turn the kettle on and then press the Keep
Warm button. The Blue Illumination Light will turn on and the kettle will begin
heating the water. As the water begins to heat, the LED Display will show the
temperature in real time.
7. Pressing the + or – buttons will increase or decrease the temperature.
8. Once the desired temperature setting is reached, the Blue Illumination Light
will turn o and stop heating. The kettle will heat occasionally in order to
maintain the selected temperature.
After pouring, make sure the bottom of the kettle and the Power Base are
dry before placing kettle back on the Power Base.
SUGGESTED TEMPERATURE USES
7
5L]LYÄSS[OLRL[[SL^P[OHU`SPX\PKZV[OLY[OHU^H[LY
<ZLKPZ[PSSLK^H[LY^OLUWVZZPISLMVYILZ[[HZ[LHUK[VTPUPTPaLTPULYHSI\PSK\WPU[OLRL[[SL
USING THE KEEP WARM TEMPERATURES
CAUTION
Place the Power Base on a sturdy,
level and dry surface.
Close the lid, ensuring it locks into
place.
6WLU[OLSPKHUKÄSS^P[O^H[LY
through the lid opening. Water must
ILÄSSLKIL[^LLU[OL¸4PU¹HUK
¸4H_¹SL]LSZPUZPKL[OLRL[[SL
Make sure that the Removable Filter
PZWYVWLYS`PUZLY[LK:LL¸9LTV]PUN
HUK0UZLY[PUN[OL-PS[LY¹VUWHNL
MVYPUZ[Y\J[PVUZVUPUZLY[PUN[OLÄS[LY
1 2 3 4
NOTE
OPERATING INSTRUCTIONS
11
USING THE STAINLESS STEEL TEA INFUSER
Boil water to desired temperature.
1. Press the Lid Button and allow steam to disperse from the kettle.
2. Place tea to be brewed into the infuser.
3. Carefully insert the infuser into the kettle by holding the infuser handle,
making sure the at side of the infuser lays parallel to the removable lter.
Close the lid and steep tea for desired length of time.
4. Once nished, remove the infuser from the kettle, close the lid and serve.
NOTE: Loose tea or tea bags can be used in the infuser.
REMOVING AND INSERTING THE FILTER
1. Do not attempt to remove lter until the unit has cooled completely.
Open the lid.
2. Grasp the tab on the lter and pull upward. The lter should slide out easily.
3. Wash and rinse the lter. Grasping the lter at the tab, slide the lter into the
slots on the inside of the spout until the lter sits securely into place.
Once the lter is securely in place, the kettle will be ready for use.
NOTE: It is necessary for the lter to be properly in place for the kettle to
shut o automatically.
