Graco President L Series Instruction manual

Instructions – Parts List
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
Copyright 1997, Graco Inc. is registered to I.S. EN ISO 9001
PresidentRAir Motors
For use with Graco fluid handling pumps.
See your pump instruction manual for Maximum Working Pressure.
Model 205647, Series L
For in-line mounting, medium-pressure oil pump
Model 206078, Series L
For in-line mounting, high-pressure grease pump
Model 205038, Series M
For stanchion tube mounting
Model 207352, Series F
For divorced mounting
Model 222772, Series F
For divorced mounting
Table of Contents
Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Drawings and Parts LIsts
Model 205647 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 206078 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 205038 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 207352 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 222772 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Hole Layouts 24. . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional Drawing 24. . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Standard Warranty 26. . . . . . . . . . . . . . . . . . . . . .
Graco Phone Number 26. . . . . . . . . . . . . . . . . . . . . . . . . .
306982AF
Read warnings and instructions.
Model 207352 Shown
Parts

2 306982
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
DThis equipment is for professional use only.
DRead all instruction manuals, tags, and labels before operating the equipment.
DUse the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
DDo not alter or modify this equipment.
DCheck equipment daily. Repair or replace worn or damaged parts immediately.
DDo not exceed the maximum working pressure stated on the equipment or in the Technical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.
DUse fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
DHandle hoses carefully. Do not pull on hoses to move equipment.
DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 66_C (150_F) or below –40_C (–40_F).
DWear hearing protection when operating this equipment.
DDo not move or lift pressurized equipment.
DComply with all applicable local, state, and national fire, electrical, and safety regulations.
DNever exceed 180 psi (1.2 MPa, 12 bar) air pressure to the motor, and never exceed the stated
maximum working pressure of the pump or the lowest rated component in your system. Refer to
your separate pump instruction manual.
DBe sure that all spray/dispensing equipment and accessories are rated to withstand the maximum
air and fluid working pressures of this system. Do not exceed the maximum working pressure of
any component or accessory used in the system.

3306982
WARNING
INJECTION HAZARD
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury.
DFluid injected into the skin is a serious injury. The injury may look like just a cut, but it is a serious
injury. Get immediate medical attention.
DDo not point the dispensing valve at anyone or any part of the body.
DDo not put your hand or fingers over the end of the dispensing valve.
DDo not stop or deflect leaks with your hand, body, glove or rag.
DUse only extensions and no-drip tips that are designed for use with your dispensing valve.
DTighten all fluid connections before operating the equipment.
DCheck the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not
repair high pressure couplings; you must replace the entire hose.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
DKeep clear of all moving parts when starting or operating the pump.
DBefore checking or servicing the equipment, follow the Pressure Relief Procedure on page 6 to
prevent the equipment from starting unexpectedly.

4 306982
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re-
sult in a fire or explosion and serious injury.
DGround the equipment and the object being sprayed. Refer to Grounding on page 5.
DIf there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately. Do not use the equipment until you identify and correct the problem.
DProvide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
DKeep the spray area free of debris, including solvent, rags, and gasoline.
DBefore operating this equipment, electrically disconnect all equipment in the spray area.
DBefore operating this equipment, extinguish all open flames or pilot lights in the spray area.
DDo not smoke in the spray area.
DDo not turn on or off any light switch in the spray area while spraying or while operating if fumes
are present.
DDo not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
DBe sure that all fluids and solvents used are chemically compatible with the wetted parts shown in
the Technical Data section of your pump manual. Always read the manufacturer’s literature before
using fluid or solvent in your pump.
DKnow the specific hazards of the fluid you are using.
DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
DAlways wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
United States Government safety standards have been adopted under the Occupational Safety and Health Act. You
should consult these standards – particularly the General Standards, Part 1910, and the Construction Standards,
Part 1926.

5306982
Installation
General Information
NOTE: Reference numbers and letters in parentheses
in the text refer to the callouts in the figures and the
parts drawing.
NOTE: Always use Genuine Graco Parts and
Accessories, available from your Graco distributor.
Grounding
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE OR EXPLOSION HAZ-
ARD on page 4.
DPump: Use a ground wire and clamp as shown in
Fig. 1. Loosen the grounding lug locknut (A) and
washer (B). Insert one end of a 12 ga (1.5 mm@)
minimum ground wire (C) into the slot in lug (D) and
tighten the locknut securely. Connect the other end
of the wire to a true earth ground.
Model No. 206078: Remove the ground screw (Z)
and insert through the eye of the ring terminal at
end of ground wire (Y). Fasten the ground screw
back onto the pump and tighten securely. Connect
the other end of the ground wire to a true earth
ground. See Fig. 2. To order a ground wire and
clamp, order Part No. 222011.
DAir, and fluid hoses: Use only electrically
conductive hoses.
DAir compressor: Follow manufacturer’s
recommendations.
DSpray gun and dispensing valve: Ground through
connection to a properly grounded fluid hose and
pump.
DObject being sprayed: Follow your local code.
DSolvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the pail
on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding
continuity.
DTo maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the spray
gun firmly to the side of a grounded metal pail, then
trigger the gun.
0720
Fig. 1
C
A
DB
Fig. 2
Z
Y
TI1052

6 306982
Installation
Pressure Relief Procedure
WARNING
INJECTION HAZARD
Fluid under high pressure can be in-
jected through the skin and cause
serious injury. To reduce the risk of an
injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you
DAre instructed to relieve the pressure
DStop spraying
DCheck or service any of the system equipment
DInstall or clean the spray tips
1. Engage the spray gun/dispensing valve safety
latch.
2. Shut off the air to the motor.
3. Close the bleed-type master air valve (required in
your system).
4. Disengage the gun/valve safety latch.
5. Hold a metal part of the gun/valve firmly to the side
of a grounded metal pail, and trigger the gun/valve
to relieve pressure.
6. Engage the gun/valve safety latch.
7. Open the pump drain valve (required in your
system), having a container ready to catch the
drainage.
8. Leave the drain valve open until you are ready to
spray/dispense again.
If you suspect that the spray tip/nozzle or hose is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the tip guard retaining nut or hose end coupling
and relieve pressure gradually, then loosen completely,
then clear the tip/nozzle or hose.
A bleed-type master air valve is required in your
system to reduce the risk of serious bodily injury
from moving parts if you are adjusting or repairing
the air motor.
The bleed-type master air valve relieves air trapped
between this valve and the motor after the air
regulator is shut off. Trapped air can cause the
motor and pump to cycle unexpectedly. Install the
valve between the pump air inlet and the air
regulator within easy reach of the pump.
WARNING
Moving parts can pinch or amputate your fingers or
other body parts. When the pump is operating, the
priming piston (located at the pump intake) and the
air motor piston (located behind the air motor
plates) move. Never Operate the pump with the air
motor plates removed, and keep your fingers and
hands away from the priming piston. See Moving
Parts Hazard on page 3.
WARNING

7306982
Operation
NOTE: See your separate pump manual for detailed
operation instructions.
Restarting a Stalled Air Motor
CAUTION
Never exceed 180 psi (1.2 MPa, 12 bar) air supply
pressure to the air motor. Exceeding this pressure
may cause the air motor to stall with the air transfer
valves stuck at mid position, making the air motor
inoperative.
To reseat the air transfer valves and restart a stalled
air motor, relieve the air supply pressure to the motor
by closing the bleed-type master air valve. If the air
transfer valves fail to reseat, screw the cap nut (F) out
of the cylinder (G), pull up on the trip rod (H) and
screw the cap nut back into the cylinder. See Fig. 2.
Be sure the air supply pressure is less than 180 psi
(1.2 MPa, 12 bar) before opening the bleed-type
master air valve.

8 306982
Service
Servicing the Air Motor
Before you Start
DBe sure you have all necessary parts on hand. Air
Motor Repair Kit 207385 includes repair parts for
the motor. Use all the parts in the kit for best
results. Parts included in the air motor kit are
marked with double asterisks (**) in text and
drawings. See the parts list and drawing for your
pump (pages 14 to 22) for further information.
DTwo accessory tools should be used. Padded
pliers, 207579 is used to grip the trip rod without
damaging its surface. Gauge, 171818, is used to
ensure the proper clearance between the poppets
and seat of the transfer valve.
Disassembly
1. Flush the pump. Follow the Pressure Relief
Procedure Warning, at left, before proceeding.
2. Disconnect the air hose from the motor. If
necessary, disconnect the motor from the pump.
Clamp the air motor base in a vise.
3. Manually push up on the piston rod to move the
piston assembly to the top of its stroke. Unscrew
the cylinder cap nut (F) from the cylinder (G). Pull
up on the cap nut. Grip the trip rod (H) with
padded pliers 207579 and screw the cap nut off
the trip rod. See Fig. 2.
CAUTION
Do not damage the plated surface of the trip rod.
Damaging the surface of the trip rod can result in
erratic air motor operation. Use the special padded
pliers, 207579, to grasp the rod.
4. Remove the eight screws (Z) holding the cylinder
(G) to the base (J). Carefully pull the cylinder
straight up off the piston. See Fig. 2.
CAUTION
To avoid damaging the cylinder wall, ALWAYS lift the
cylinder straight up off of the piston. Never tilt the
cylinder as it is being removed.
Always keep fingers clear of the toggle assemblies
(E), to avoid pinching or amputating them. See
Fig. 3.
WARNING
5. Use a screwdriver to push down on the trip rod
yoke (K) and snap the toggle assemblies (E)
down. See Fig. 3. Remove the lockwires (L) from
the adjusting nuts (M and Q) of the transfer valves
(N). Screw the top nuts (M) off. Screw the valve
stems (O) out of the grommets (P) and lower
adjusting nuts (Q). Take the valve poppets (R) off
the stems and squeeze them firmly to check for
cracks.
Fig. 2
G
Z
J
BB
H
Hold trip rod with
padded pliers
207579, to prevent
damage to rod
F

9306982
Service
6. Grip the toggle rockers (S) with a pliers. Compress
the springs (T) and swing the toggle assembly (E)
up and away from the piston lugs (U), and remove
the parts. Check that the valve actuator (V) is
supported by the spring clips (W), but slides easily
into them. See Fig. 3.
7. Remove the trip rod yoke (K), valve actuator (V)
and trip rod (H). Check the exhaust valve poppets
(X) for cracks.
NOTE: To remove the exhaust valve poppets (X),
stretch them out and cut with a sharp knife.
8. Pull the piston (Y) up out of the base (J) and
inspect the piston o-ring (AA) and the o-ring in the
base casting.
Cut off tops of
poppets (x) as
indicated by dotted
lines
0.125 in.
(3.18 mm)
CUTAWAY VIEW
Fig. 3
E
Push toggles (E) in
and then up.
Turn wires up.
U
HK L**
M**
O**
P**
Y
J
T
S
WX** V
Q**
R**
H
W
V
X**
O** M**
P**
Q**
AA**
Y
R**
N

10 306982
Service
Reassembly
1. Clean all the parts carefully in a compatible solvent
and inspect for wear or damage. Use all the repair
kit parts during reassembly and replace other parts
as necessary.
2. Check the polished surfaces of the piston, piston
rod and cylinder wall for scratches or wear. A
scored rod will cause premature packing wear and
leaking.
3. Lubricate all parts with a light, waterproof grease.
4. Be sure the o-rings are in place. Slide the piston
rod down through the throat bearing and lower the
piston (Y) into the air motor base (J).
5. Pull the exhaust valve poppets (X**) into the valve
actuator (V) and clip off the top part shown with
dotted lines. See Fig. 3.
6. Install the transfer valve poppets (R**) onto the
valve stems (O**), then reassemble the valve
stems (O**), bottom adjusting nuts (Q**),
grommets (P**), and top adjusting nuts (M**) on
the piston (Y). Assemble the trip rod (H), valve
actuator (V), trip rod yoke (K) and toggle
assemblies (E) on the piston. See Fig. 3.
7. Before installing the lockwires (L**) in the adjusting
nuts (M** and Q**), use the special gauge 171818
to adjust the transfer valve (N) so there is 0.125 in.
(3.18 mm) clearance between the poppets (R**)
and the piston (Y) when the toggle assemblies are
in the down position. See Fig. 3.
8. Snap the toggle assemblies (E) to the up position.
Reinstall the cylinder (G) and cap nut (F).
Reassemble the air motor to the displacement
pump.
9. Before remounting the pump, connect an air hose
and run the pump slowly, at about 40 psi
(0.28 MPa, 2.8 bar) to ensure that it operates
smoothly.
10. Reconnect the ground wire before regular
operation of the pump.

11306982
Service
Throat Packing Service for In-Line Pump Model 205647
The piston in the air motor, located behind the air
motor plates, moves when air is supplied to the
motor. Moving parts can pinch or amputate your
fingers or other body parts. Therefore, never
operate the pump with the air motor plates
removed.
WARNING
NOTE: See Fig. 4 on page 12 and the Parts Drawing
on page 14.
1. Clamp the pump in a vise and unscrew the
displacement cylinder (CC) from the air motor
base (J). Pull the displacement cylinder away from
the air motor until the cotter pin (DD) which
secures the displacement pump connecting rod to
the air motor piston rod (FF) is visible. See Fig. 4.
2. Remove the cotter pin (DD) and unscrew the pump
connecting rod (EE) from the air motor piston rod
(FF). See Fig. 4. Remove the cylinder (G) from the
air motor base (J) as described under
Disassembly on page 8.
3. Remove one louvered air exhaust plate (BB) and
unscrew the throat packing nut (HH), using a
spanner wrench or a 0.22 in. (5.6 mm) diameter
rod. See Fig. 4. Remove the spacer and packing
from the base and packing nut. Clean the throat
packing area in the base and the packing nut.
Clean and inspect all parts and replace as
necessary.
4. Lubricate the packings, piston rod and piston
flange with a light waterproof grease. Reinstall the
spacer and packing in the base and packing nut.
Be sure the lips of the v-packings face down. See
Detail B. Screw the packing nut loosely into the
base. Carefully slide the piston rod down through
the throat packing and lower the piston into the
base. Tighten the packing nut securely. Reinstall
the plate (BB) and cylinder (G). Reassemble the
air motor to the displacement pump.
CAUTION
When reinstalling cotter pin (DD), always spread and
flatten the pin (both the head and prongs) around the
rod to within a 1 in. (25 mm) total diameter. See
Detail A of Fig. 4.

12 306982
Service
Fig. 4
HH
BB
CC
J
G
SEE DETAIL A
FF
DD
EE
1 in.
(25 mm)
DETAIL A
NOTE: To avoid seal damage during installa-
tion, insert the seal at an angle as shown above,
so that side A is below hole C. Then press side
B down until the seal bottoms out.
C
A
190249
B
112843
190495
DETAIL B, for In-Line Pump Model 205647
In-Line Pump Models
205647 and 206078

13306982
Service
Throat Packing Service for In-Line Pump Model 206078
The piston in the air motor, located behind the air
motor plates, moves when air is supplied to the
motor. Moving parts can pinch or amputate your
fingers or other body parts. Therefore, never
operate the pump with the air motor plates
removed.
WARNING
See Fig. 4 on page 12 and the Parts Drawing on
page 16.
1. Clamp the pump in a vise and unscrew the
displacement cylinder (CC) from the air motor
base (J). Pull the displacement cylinder away from
the air motor until the cotter pin (DD) which
secures the displacement pump connecting rod to
the air motor piston rod (FF) is visible. See Fig. 4.
2. Remove the cotter pin (DD) and unscrew the pump
connecting rod (EE) from the air motor piston rod
(FF). See Fig. 4. Remove the cylinder (G) from the
air motor base (J) as described under
Disassembly on page 8.
3. Remove one louvered air exhaust plate (BB) and
unscrew the throat packing nut (HH), using a
spanner wrench or a 0.22 in. (5.6 mm) diameter
rod. See Fig. 4.
4. Remove the packing nut (45{), male and female
glands (47{, 48{), v-packings (49{), washer
(44{), bearing (46{), retainer (24{), wiper (22{),
o-ring (23{), u-cup (25{), and washer (26{) from
the base.
5. Clean the throat packing area in the base and the
packing nut. Clean and inspect all parts, and
replace as necessary.
6. Lubricate the packings, piston rod and piston
flange with a light waterproof grease.
7. Install the washer (26{) into the base. Assemble
the packing (25{) and the wiper (22{) into the
retainer (24{). Install the o-ring (23{) onto the
retainer, and insert the retainer assembly into the
base.
NOTE: Make sure the packing (25{) lips face
down, and make sure the wiper (22{) lips face up.
8. Insert the bearing (46{) and the washer (44{) into
the base. Assemble the female gland (48{),
v-packings (49{), and the male gland (47{) into
the packing nut (45{).
9. Reinstall the spacer and packing in the base and
packing nut (45{). Screw the packing nut into the
base, and tighten it securely. Carefully slide the
piston rod (FF) down through the throat packing,
and lower the piston into the base. Reinstall the
plate (BB) and cylinder (G). Reassemble the air
motor to the displacement pump.
10. Torque the outlet adapter (42) to 45 to 55 ft-lb (61
to 75 N-m).
CAUTION
When reinstalling cotter pin (DD), always spread and
flatten the pin (both the head and prongs) around the
rod to within a 1 in. (25 mm) total diameter. See
Detail A of Fig. 4.

14 306982
Parts
Model 205647, Series L
for in-line mounting, medium-pressure oil pump
1
2
3
*4
5
6
7
8
*9
10*
13 14
15
16
17
18**
19
**20
21**
24
25
27**
27**
28**
29
30**
31
32
33
34
35
36
33
37**
38**
5354
57
58

15306982
Parts
Model 205647, Series L
for in-line mounting, medium-pressure oil pump
Ref
No. Part No. Description Qty
1 207150 TRIP ROD 1
2 207391 PISTON
includes items 3 to 5 (also includes
207385 repair kit when ordered
as a replacement part) 1
3 102975 .SCREW, rd hd mach; 6–32 x 1/4 in. 2
4 158361* .CLIP, spring 2
5 .BARE PISTON (not sold separately) 1
6 100078 SCREW, hex head; 8–32 x 3/8 in. 20
7 101578 SCREW, hex head Nylock;
8–32 x 3/8 in. 8
8 150647 GASKET; copper 1
9 156698* O-RING; Buna–N 1
10 112843* PACKING, block, V 1
13 158359 ACTUATOR, valve 1
14 158360 YOKE, rod, trip 1
15 158362 PIN, toggle 2
16 158364 ROCKER, toggle 2
17 167585 SPRING, helical compression 2
18 158367** GROMMET; rubber 2
19 158377 SEAL, flat ring; nitrile rubber 1
20 158378** SEAL, o-ring; nitrile rubber 1
21 158379** SEAL, o-ring; nitrile rubber 1
24 190495 SPACER, throat 1
25 190249 NUT, packing 1
27 160261** NUT, adjusting 4
28 160618** LOCKWIRE, transfer valve 2
29 160623 ARM, toggle 2
Ref
No. Part No. Description Qty
30 160896** STEM, valve 2
31 161435 NUT, cylinder cap 1
32 162629 CYLINDER, motor, air 1
33 178270 PLATE, muffler 2
34 164924 BASE, motor, air 1
35 164925 ROD, piston 1
36 177844 PLATE, identification 1
37 170708** POPPET, valve; urethane 2
38 170709** POPPET, valve; urethane 2
53 104029 LUG, grounding 1
54 104582 WASHER, tab 1
57 180233 LABEL, warning 2
58Y177843 PLATE, warning 1
* Recommended spare parts to keep on hand.
** Included in Repair Kit 207385. Must be
purchased separately.
YIf users of this equipment do not read English, you
may order one of the following labels to apply to
your air motor. Apply the label over the matching
label on the air motor plate for good visibility. Do
not cover the air exhaust holes. Order the labels
free of charge directly from Graco. Contact your
distributor to order.
French 290466
Spanish 290468

16 306982
Parts
1
2
3
*4
5
7
8
*9
13
14
15
16
17
18**
**20
27**
27**
28**
29
30**
31
32
36
37**
38**
33
Model 206078, Series L
for in-line mounting, high-pressure grease pump
42
40
52
56
48{
06733B
46{
22{
45{
23{
24{
25{
26{
44{
47{
49{
21**
19
58
53
33 57
6
1Torque to 45 to 55 ft-lb (61 to 75 N-m).
1

17306982
Parts
Model 206078, Series L
for in-line mounting, high-pressure grease pump
Ref
No. Part No. Description Qty
1 207150 TRIP ROD 1
2 207391 PISTON
includes items 3 to 5 (also includes
207385 repair kit when ordered
as a replacement part) 1
3 102975 .SCREW, rd hd mach; 6–32 x 1/4 in. 2
4* 158361 .CLIP, spring 2
5 .BARE PISTON (not sold separately) 1
6 100078 SCREW, hex head; 8–32 x 3/8 in. 20
7 101578 SCREW, hex head Nylock;
8–32 x 3/8 in. 8
8 150647 GASKET; copper 1
9* 156698 O-RING; Buna–N 1
13 158359 ACTUATOR, valve 1
14 158360 YOKE, rod, trip 1
15 158362 PIN, toggle 2
16 158364 ROCKER, toggle 2
17 167585 SPRING, helical compression 2
18** 158367 GROMMET; rubber 2
19 158377 SEAL, flat ring; nitrile rubber 1
20** 158378 SEAL, o-ring; nitrile rubber 1
21** 158379 SEAL, o-ring; nitrile rubber 1
22{113935 WIPER, rod 1
23{113944 PACKING, o-ring 1
24{192172 RETAINER, packing 1
25{113936 PACKING, u-cup 1
26{192173 WASHER, packing 1
27** 160261 NUT, adjusting 4
28** 160618 LOCKWIRE, transfer valve 2
29 160623 ARM, toggle 2
30** 160896 STEM, valve 2
31 161435 NUT, cylinder cap 1
32 162629 CYLINDER, motor, air 1
33 178270 PLATE, muffler 2
36 177844 PLATE, identification 1
15E555 for FireBallr425 models: 205394,
205395,239729, 239730 and 239731
37** 170708 POPPET, valve; urethane 2
38** 170709 POPPET, valve; urethane 2
Ref
No. Part No. Description Qty
40 150461 GASKET; copper 1
42 158409 ADAPTER, outlet 1
44{158697 WASHER, thrust 1
45{159047 NUT, packing 1
46{159048 BEARING, brass 1
47{159306 GLAND, male 1
48{159307 GLAND, female 1
49{159308 V-PACKING; nitrile rubber 4
52 162553 ROD, piston 1
53 116343 SCREW, grounding 1
56 15F570 BASE, motor, air 1
57 180233 LABEL, warning 2
58Y177843 PLATE, warning 1
* Recommended spare parts to keep on hand.
** Included in Repair Kit 207385. Must be purchased
separately.
{Service parts for air motor throat packing area.
Must be purchased separately.
YIf users of this equipment do not read English,
you may order one of the following labels to
apply to your air motor. Apply the label over the
matching label on the air motor plate for good
visibility. Do not cover the air exhaust holes.
Order the labels free of charge directly from
Graco. Contact your distributor to order.
German 290467
French 290466
Spanish 290468

18 306982
Parts
1
2
3
*4
5
6
13 14
15
16
17
18**
19
**20
21**
22**
22**
23**
24
33**
Model 205038, Series M
for stanchion tube mountings
30
*12
27
11
32**
25**
10
26
8
9
28 31
35 34
7
363837
29

19306982
Parts
Model 205038, Series M
for stanchion tube mountings
Ref
No. Part No. Description Qty
1 207150 TRIP ROD 1
2 207391 PISTON
includes items 3 to 5 (also includes
207385 repair kit when ordered
as a replacement part) 1
3 102975 .SCREW, rd hd mach; 6–32 x 1/4 in. 2
4 158361* .CLIP, spring 2
5 .BARE PISTON (not sold separately) 1
6 114422 SCREW, pan head; 8–32 x 3/8 in. 20
7 101524* SEAL, wiper; leather 1
8 101525 RING, retainer 1
9 101526 BEARING; bronze 1
10 101578 SCREW, hex head Nylock;
8–32 x 3/8 in. 8
11 150647 GASKET; copper 1
12 156698* O-RING; Buna–N 1
13 158359 ACTUATOR, valve 1
14 158360 YOKE, rod, trip 1
15 158362 PIN, toggle 2
16 158364 ROCKER, toggle 2
17 167585 SPRING, helical compression 2
18 158367** GROMMET; rubber 2
19 158377 SEAL, flat ring; nitrile rubber 1
20 158378** SEAL, o-ring; nitrile rubber 1
21 158379** SEAL, o-ring; nitrile rubber 1
22 160261** NUT, adjusting 4
23 160618** LOCKWIRE, transfer valve 2
24 160623 ARM, toggle 2
25 160896** STEM, valve 2
Ref
No. Part No. Description Qty
26 162628 ROD, piston 1
27 162629 CYLINDER, motor, air 1
28 178270 PLATE, muffler 1
29 162663 BASE, motor, air 1
30 164704 NUT, cylinder cap 1
31 177844 PLATE, identification 1
32 170708** POPPET, valve; urethane 2
33 170709** POPPET, valve; urethane 2
34 104029 LUG, grounding 1
35 104582 WASHER, tab 1
36 180233 LABEL, warning 2
37Y177841 PLATE, warning 1
38 178269 PLATE, muffler 1
* Recommended spare parts to keep on hand.
** Included in Repair Kit 207385. Must be
purchased separately.
YIf users of this equipment do not read English, you
may order one of the following labels to apply to
your air motor. Apply the label over the matching
label on the air motor plate for good visibility. Do
not cover the air exhaust holes. Order the labels
free of charge directly from Graco. Contact your
distributor to order.
German 290464
French 290463
Spanish 290465

20 306982
Parts
18**
19
**20
21**
22**
22**
23**
24
27
25**
28
Model 207352, Series F
for divorced mountings
26
*13
30
17
16
14 15
34**
7
*8
9
6
33**
12
29
11
32
1
includes
items 2 to 4
38
10
31 28 37
36 35
5