Graco 17B587 User manual

Kit Instructions
Double Bead Box Kit
17B587 (8”) or 17B361 (12”)
For adding a second bead box to the ThermoLazer 200 or 200TC.
To be used on 200/200TC models only.
Models
17B587 – 8” (20cm), 17B361 – 12” (30cm)
Follow these instructions when adding the second bead box to an existing 8-inch (20cm) or 12-inch (30cm) bead box
on the ThermoLazer 200 or 200TC. Refer to the ThermoLazer Repair and Operation manuals as need for additional
information.
IMPORTANT SAFETY INSTRUCTIONS
Read all warnings and instructions in ThermoLazer Operation manual.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
Related Manuals:
3A1319
3A1320
334146A
EN
ti24490a

Preparation
2334146A
Preparation
1. Close manual gas shut-off valve on propane tank.
2. Disconnect hose from tank.
3. Remove propane tank from unit.
4. Cut tie wrap that secures propane line to bead hose.
5. Loosen screws on hose clamps and remove bead
hose from dispenser and bead hopper. Save for
reuse.
ti24109a
ti24489a
ti24499a
ti24502a

Preparation
334146A 3
6. Remove screws from bead hopper. Save for reuse.
Screws are accessible from the propane tank side
of the box.
7. Remove bead hopper. Dispose of bead hopper.
8. Loosen screw and remove bead dispenser engage-
ment wheel. Dispose of wheel and screw.
9. Install two angular inserts (A) on bead dispenser
with screws provided and tighten screws.
ti24504a
ti24506a
ti24514a

Installation
4334146A
Installation
1. Slide rear bead box down through slots on angular
brackets to lock into place.
2. Slide single pulley over long axle.
3. Slide bead dispenser engagement wheel pulley
onto long axle.
4. Secure pulley and wheel into place with retaining
ring (engagement wheel with pulley will rotate
freely).
5. Slide pulley onto short axle.
ti24519a
ti24524a
ti24523a
ti24522a
ti24521a

Installation
334146A 5
6. Install belts onto pulleys.
7. Align pulleys as shown below and tighten screws.
8. Attach pulley guard and tighten two screws.
9. Install new dual compartment bead box using
screws saved in Preparation Step 6.
10. Attach bead hose (Saved in Preparation Step 5.)
from rear bead box to rear dispenser and tighten
hose clamps.
ti24520a
ti24525a
ti24528a
ti24527a

Installation
6334146A
11. Attach bead hose from front bead box to front dis-
penser and tighten hose clamps.
ti24529a
The rear bead dispenser has a higher drop rate
than the front bead dispenser.

Parts 17B361, 17B587
334146A 7
Parts 17B361, 17B587
31
41
15
6
78
18
4
4
2
12
16
16
5
5
1
17
19
13
42
31
10 11
10
9
27
25
19
19
34
32
33
30
29
26
20
20
21
21
54
57
56
ti24530a

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 334146
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision A, October 2014
Parts List 17B361, 17B587
Ref. Part Description Qty.
1 123261 SCREW, thumb 1
2 123481 SCREW, shoulder, screw, 1/4-20 2
3 295709 SCREW, cap, socket head 1
4 15X282 HANDLE, adjuster 1
5 110631 SCREW, socket head 8
6 16Y163 BRACKET, left, bead dispenser 1
7 123304 BEARING, double sealed 2
8 114797 GASKET 2
9 15X274 GATE, poly 1
10 15X275 GATE, bar 1
11 SCREW, cap, shoulder
112310 Kit 17B587 3
112310 Kit 17B361 4
12 SHAFT, adjuster 1
16Y166 Kit 17B587
15X281 Kit 17B361
13 PLATE, slide, 1"
16U612 Kit 17B587 8
16U612 Kit 17B361 12
14 SPRING, compression
114708 Kit 17B587 8
114708 Kit 17B361 12
15 104034 WASHER, plain
Kit 17B587 16
Kit 17B361 24
16 119872 SCREW, shoulder
Kit 17B587 8
Kit 17B361 12
17 SHAFT, knurled 1
16Y161 Kit 17B587
16A333 Kit 17B361
18 16Y162 BRACKET, right, bead dispenser 1
19 16A805 SHAFT, short 1
20 HOUSING, dispenser 1
16Y160 Kit 17B587, 8” (20cm)
16Y172 Kit 17B361, 12” (30cm)
21 16Y168 GASKET, cover 1
22 16Y169 MANIFOLD, cover 1
23 106084 SCREW, machine, pan head 6
29 104705 SCREW, cap, shoulder 2
30 100050 SCREW, set, shoulder 4
31 113983 RING, retaining, ext. 1
32 16Y230 CLAMP, hose 2
33 17B456 BOX, double bead box 1
34 17B463 WHEEL, drive bead, assembly 1
35 17C509 HOSE, bead hose 20.5" 1
36 17B555 COVER, belt 1
37 514930 SCREW, cap, socket head 2
38 123526 BELT, outer 1
39 123527 BELT, inner 1
40 16A802 PULLEY, double 1
41 16A803 PULLEY, large 1
42 16A804 INSERT, bead box 2
4416A276 LABEL, ISO symbols warn & instru 1
45 16E335 LABEL, brand, GRACO 2
46 16X975 LABEL, brand, THERMOLAZ-
ER200TC, FR
1
47 16Y468 GASKET, beads box 1
Replacement Danger and Warning labels, tags, and
cards are available at no cost.
Ref. Part Description Qty.