Graco 25M713 User manual

For use on RoadPak™Line Striping Systems to lift the gun arm during spray operations.
Model 25M713
Important Safety Instructions
Read all warnings and instructions in this manual and in related manuals.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
Related Manuals:
3A5384 Operation
3A5405B
EN
Instructions
Winch Kit for RoadLazer™RoadPak™
RoadPak HD™Line Striping System

Installation
23A5405B
Installation
1. Assemble adapter bracket (1) to height adjustment
bracket on both sides. Fasten with bolts (6),
washers (7), and nuts (8). Torque to 28 ft-lb.
2. Use four bolts and lock washers (supplied) to
assemble winch (5) onto winch arm (2).
3. Use bolts, washers, and nuts (supplied) to
assemble cable guide onto winch arm bracket (3).
4. Slide winch arm bracket (3) into winch arm (2) and
secure into place by tightening extension clamp (15)
and inserting the safety pin.

Installation
3A5405B 3
5. Insert winch assembly into one of the adapter brack-
ets (1) and secure with pin (9).
6. Slide terminal boots (supplied) onto both ends of the
blue and yellow cables (25). Connect each cable to
the corresponding color-coded terminal on the
winch. Cover terminal with terminal boot.
7. Install split sleeving (26) over cables (25) and cut to
needed length.
8. Connect blue and yellow cables (25) from the winch
terminals to the blue and yellow color-coded termi-
nals on the winch switch terminal. Cover terminal
with terminal boot. See Wiring Diagram, page 4.
NOTE: If the winch runs in the opposite direction as indi-
cated on the control, swap the positions of the yellow
ans blue wire connections on the winch.
9. Plug in winch controller (19) to the connector at the
junction box. Properly protect and secure all wires to
keep from damaging them during every day use.
25

Wiring Diagram
43A5405B
10. Adjust the winch arm (3) so it is in line with the lifting
point on the gun arm. Ensure the winch arm is
secured by pinning it and tightening the extension
clamp (15).
11. Use the buttons on the controller (19) to lower the
winch. Connect the winch hook (22) to the lifting
point on the gun arm.
12. When transporting the RoadPak system, the gun
arm must be properly stowed (see manual 3A5384)
and the winch arm must be adjusted to fit within the
width of the vehicle.
Wiring Diagram

Parts List
3A5405B 5
Parts List
Ref. Part Description Qty.
1 16G688 BRACKET, adapter, winch, painted 2
2 24G839 ARM, winch, painted 1
3 24G841 BRACKET, arm, winch, painted 1
5 25M738 WINCH, RoadLazer 1
6 101147 SCREW, cap, hex HD 4
7 109570 WASHER, plain 8
8 801020 NUT, lock, hex 4
9 115473 PIN, hitch 2
10 186812 CHAIN, ground 3.5 HP 2
11 M71635 CLAMP, hose 2
12 100678 SCREW, cap hex HD 1
13 111040 NUT, lock, insert, nylock, 5/16 1
14 100023 WASHER, flat 6
15 238813 CLAMP, extension 1
19* 17U973 SWITCH, corded remote 1
22* 16H068 CARBINER, 1-3/8 in. eye dia. 1
23* 17U972 CABLE, 5/16 in. dia., black 1
25* 17U974 WIRE, assembly, winch 1
26 17X001 SLEEVING, split, 20 ft. 1
* Included in 25M738.
Ref. Part Description Qty.

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents
Original instructions. This manual contains English. MM 3A5405
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2016, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision B, March 2018